Lockly Vision PGD628F Peek-Proof Smart Lock User Manual
Welcome!
This guide will walk you through step-by-step how to install and get your Lockly Secure up and running. Installation generally takes less than 30 minutes. If you have any questions please reference our online support at: Lockly.com/support or call (669) 500-8835 for help.
Preparation
To complete the installation you will need:
Drilling is not required to install the lock and is optional. However, if you are installing your lock on a brand-new door, a drill is required if there are no holes prepared for lock installation.
Remove existing door hardware, latch, or deadbolts before installing the new lock. Use the provided template to bore new holes if needed.
- Measure and confirm your door is between 1-3/8″ ~ 2″ (35mm – 50mm).
- Measure and confirm the hole in the door is 2-1/8″ (54mm) .
- Measure and confirm that the backset is between 2-3/8″ (60mm) to 2-3/4″ (70mm).
- Measure and confirm that the hole in the door edge is 1″ (25mm).
IMPORTANT NOTICE
You are not required to drill an extra hole in your door. We have provided double-sided adhesive tape for you to help stabilize the lock during installation. Only drill a hole if you wish to have added stability. Please refer to the provided template for drilling if needed. Use goggles to protect your eyes if you need to drill door holes.
INSTALLING THE LOCKSET
Measure the distance between the center of the front door hole to the edge of your door. Push the shaft (a) to adjust the lockset to 2-3/8″(60mm) or 2-3/4″(70mm).
Facing the door exterior, install the lockset according to the in-swing or out-swing opening direction of your door.
Secure the lockset with provided G screws.
CHANGING HANDLE FOR RIGHT OR LEFT SWING DOORS
The lock ships with a handle default for the right in-swing or left out-swing door. Check the diagram below if you are unsure of your door orientation.
Changing the Exterior Handle Orientation
Insert the key and rotate the lock face so that the two white dots align as shown.
Use the provided pin insert R to push the metal pin located at the 3 o’clock of the base handle, then the other pin at the 9 o’clock position. Remove the handle once the pins are compressed.
Rotate the handle 180° to the other side of the lock. Using your fingers, press the two pins located on the left and right side of the lock to insert the handle back into the lock.
Confirm that your installation was complete by checking if the pins are flush against the handle, and have popped out. Adjust the handle accordingly to make sure the pins are fully decompressed and sit flush against the surface.
Check that your handle works smoothly by giving it a turn-up and down.
Twist the key back to a horizontal position. The key can be taken out once it goes back to the horizontal position.
Changing the Interior Handle Orientation
Remove the screw by turning counterclockwise and rotate the handle 180° in the direction of the arrow as shown. Make sure the screw hole is aligned with the marker as illustrated. Securely screw clockwise as shown to complete your handle orientation change.
If you drilled a hole in Preparation, use Slotted Barrel Extension U and securely tighten with a flathead screwdriver by turning it clockwise onto the lock. If you did not drill a hole in Preparation, you can leave this pole removed.
Install the exterior lock as shown to the left by aligning the lock straight and passing the cable and attached rods through the lockset.
Pass the Spindle C through the center of the lockset, and the round rods through the sides in their respective holes. The cable should run underneath the lockset.
Align the lock straight and press hard (if you use the Adhesive tape in step 3.4) to secure the top of the lock.
INSTALLING THE LOCK (INTERIOR)
Insert Positioning Rods V into the holes to the left and right of the Spindle C. The holes are located at the 3 o’clock and 9 o’clock positions.
Interior Mounting Plate LK will go against the interior side of your door. Remove the paper layer of the Adhesive Tape and align the positioning rods on the bottom of the plate to the corresponding left and right holes. Install the side with the black plastic seal against the door.
Pull the cable from the locked exterior through the rectangular hole underneath the positioning rods and spindle. Secure the hole above the spindle with screws O.
Remove the position rods V and replace them with screws O Tighten clockwise until the mounting plate is secure. * If you have drilled a hole on the top in Preparation, please secure the hole with screw M1 or M2 depending on your door thickness. Skip this if no hole was drilled in Preparation.
DOWNLOAD THE LOCK APP
Congratulations! You have completed the Lockly Secure physical lock installation. To complete your setup, download the Lockly app from the App Store or on Google Play and follow the on-screen instructions.
Add more Smart to your Home
Secure Link Wi-Fi Hub
Add the optional Lockly Secure Link Wi-Fi Hub, together with the free Lockly app, it’s easier than ever to securely control and manage your door from anywhere, anytime.
Real-time, monitoring, & status
Monitor open/closed door status with real-time alerts sent to your smartphone, no matter where you are.
FCC Warning：
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
NOTE 2:
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The Secure Link Wi-Fi Hub complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator & your body.
INSTALLATION OVERVIEW & PARTS LIST
This lock can be installed for both right swing and left swing doors. The lock ships ready for a right swing door installation. If you wish to change the orientation of the lock for a Left Swing door, follow instructions on Installation Guide (Step 2) or the BILT App (Step 10).
Copyright 2022 Lockly All rights reserved
CHINA ZL 2013 1 0487970.4 | HONG KONG HK1194496 | TAIWAN 621028 | EUROPE EP3 059 689 B1 | AUSTRALIA 2013403169 | RUSSIA RU2665222 | KOREA 10-1860096 | INDONESIA IDP000064051 | Other Patents Pending The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. , and any use of such marks by Lockly is under license. Other trademarks and trade names are those of their respective owners. Google, Android, Google Play, and Google Home are trademarks of Google LLC. , Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc., or its affiliates.
REFERENCE LINK
https://lockly.com/products/lockly-secure-advanced-smart-lock-door
