Philips TAT4506 Headphones 4000 Series User manual
Important safety instructions
Hearing Safety
To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.
- Be sure to observe the following guidelines when using your headphones.
- Listen at reasonable volumes for reasonable periods of time.
- Be careful not to adjust the volume continuously upwards as your hearing adapts.
- Do not turn up the volume so high that you can’t hear what’s around you.
- You should use caution or temporarily discontinue use in potentially hazardous situations.
- Excessive sound pressure from earpieces and headphones can cause hearing loss.
- Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving.
- For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.
General information
To avoid damage or malfunction:
Caution
- Do not expose headphones to excessive heat
- Do not drop your headphones.
- Headphones shall not be exposed to dripping , splashing water.
- Do not allow your headphones to be submerged in water.
- Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
- If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
- The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like.
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
- Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas;
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
About operating and storage temperatures and humidity
- Store in a place where temperature is between -20°C (-4°F) and 50°C (122 °F) (up to 90% relative humidity.
- Operate in a place where temperature is between 0°C (32°F) and 45°C (113 °F) (up to 90% relative humidity.
- Battery life may be shorter in high or low temperature conditions.
- Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types);
Your True wireless earpieces
Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/support. With this Philips True wireless earpieces, you can:
- enjoy convenient wireless handsfree calls;
- enjoy and control wireless music;
- switch between calls and music.
What’s in the box
Other devices
A mobile phone or device (e.g. notebook, PAD, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the earpieces (see ‘Technical data’ on page 10).
Overview of your True wireless earpieces
Get started
Charge the battery
Note
- Before you use your earpieces for the rst time, place the earpieces in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime.
- Use only the original USB-C charging cable to avoid any damage.
- Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces o.
Charging Box
Connect one end of the USB cable into the charging box, and another end into the power source.
- The charging box starts charging.
- Charging process is verified by the blue LED light on the front panel.
- When the charging box is fully charged, the blue light goes on.
Tip
- The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it supports 3 times full recharge cycle for the earpieces.
Earpieces
Place the earpieces in the charging box.
- The earpieces start charging.
- Charging process is verified by blue LED light on the earpieces.
- When the earpieces is fully charged, the blue light goes o.
Tip
- Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable.
Pair the earpieces with your Bluetooth device for the first time
- Make sure that the headphones is fully charged and powered o.
- Open the top cover from charging box.
- The LED on both earpieces ash in white & blue alternately.
- The earpieces are now in pairing mode and is ready to pair with a Bluetooth device (e.g. a mobile phone)
- Turn on the Bluetooth function of your Bluetooth device.
- Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.
Note
- After powering on, if the earpieces cannot nd any previously connected Bluetooth device, it will automatically switch to pairing mode.
The following example shows you how to pair the earpieces with your Bluetooth device.
- Turn on the Bluetooth function of your Bluetooth device, select Philips TAT4506.
- Enter the earpieces password “0000” (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.
Single earpiece (Mono mode)
Take either right or left earpiece out from charging box for Mono use. The earpiece will power on automatically. There will be a voice “Power on” from earpiece.
Note
- Take the second Earpiece from the charging box and they will pair each other automatically.
Pair the earpieces with another Bluetooth device
If you have another Bluetooth device that you want to pair with the earpieces, make sure the Bluetooth function in any other previously paired or connected devices is turned of. Long touch over 5 seconds both left & right side simultaneously with earpiece on ear, release when Pairing voice prompt is heard.
Note
- The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.
Use your earpieces
Connect the earpieces to your Bluetooth device
- Turn on the Bluetooth function of your Bluetooth device.
- Open the top cover from charging box.
- The blue LED ashes.
- The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earpieces will enter pairing mode.
Tip
- The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
- If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.
Note
- If the earpieces fail to connect to any Bluetooth device within 5 minutes, it will turn of automatically to save the battery life.
- In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually.
Control ANC (active noise cancelation)
Enable ANC
Different ANC mode can be toggled via double tap on the right earpiece.
- ANC function is auto active when put into the ear.
- Touch the MFB button twice, it will change to Awareness mode.
- Touch the MFB button twice again, it will turn the ANC function o.
Tip
By removing the earpiece, it will automatically change to sleep mode. When put earpiece back, it will return to active mode.
ANC LED indicator status
Power on/off
Manage your calls and music
LED indicator status
Charging Box (4 blue LED)
Tip
- When USB is of, the LED is lit for 30s after case open or closed
Battery LED indicator on Bluetooth device
It will show a battery indicator on Bluetooth device after connected to earpieces.
Voice Assistant
How to wear
Reset the earpieces
If you encounter any pairing or connection issue, you can follow the following procedure to reset your headset.
- On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT4506 from the device list.
- Turn off the Bluetooth function of your Bluetooth device.
- Return earpieces to charging box & open the lid.
- Short press twice on casing button.
- Follow steps in “Use your earpieces Connect the earpieces to your Bluetooth device.”
- Pair the earpieces with your Bluetooth device, select Philips TAT4506
Technical data
- Music time: 6 hours
- Talk time: 6 hours
- Standby time: 200 hours
- Charging time: 2 hours
- Lithium-ion battery 50 mAh on each earpiece, Lithium-ion battery 500 mAh on charging box
- Bluetooth version: 5.0
- Compatible Bluetooth profiles:
- HFP (Hands-Free Profile)
- A2DP (Advanced Audio Distribution Profile)
- AVRCP (Audio Video Remote Control Profile)
- Supported audio codec: SBC
- Frequency range: 2400-2483.5 MHz
- Transmitter power: < 10 dBm
- Operating range: Up to 10 meters (33feet)
- Auto power or
- USB-C port for charging
- Low battery warning: available
Note
- Specifications are subject to change without notice.
Notice
Declaration of conformity
Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can and the Declaration of Conformity on www.p4c.philips.com.
Disposal of your old product and battery
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
This symbol on a product means that the product is covered by European Directive 2012/19/EU.
This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.
Remove the integrated battery
If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.
- Make sure the earpieces is disconnected from the charging box before removing the battery.
- Make sure the charging box is disconnected from the USB charging cable before removing the battery.
Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (butter) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Notice of compliance
The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Trademarks
Bluetooth
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.
Google and Google Play are trademarks of Google LLC.
DOWNLOAD PDF LINK
https://www.usa.philips.com/c-p/TAT4506BK_00/true-wireless-headphones
