Dreo-Oil-Filled-Heater -image-10

DREO Pilot Max Tower Fan User Manual

DREO LOGO

DREO Pilot Max Tower Fan User Manual

 Dreo-Oil-Filled-Heater -image-9

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS.KEEP FOR FUTURE REFERENCE.
FOR HOUSEHOLD USE ONLY
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,electric shock, and injury to persons, including the following:

  • Read all instructions before using this heater.
  • This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use the handle when moving this heater.
  • Keep combustible materials, such as furniture, pillows,bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
  • Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.Always unplug heater when not in use.
  • Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/or repair.
  • Do not use outdoors.
  • This heater is not intended for use in bathrooms,laundry areas and similar indoor locations. Never locate
    heater where it may fall into a bathtub or other water container.
  • Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. To disconnect heater, turn controls to off, then remove plug from outlet.
  • Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
    electric shock or fire, or damage the heater.
  • To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces,like a bed, where openings may become blocked.
  • A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable
    liquids are used or stored.
  • Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
  • Always plug heaters directly into a wall outlet/receptacle.Never use with an extension cord or relocatable power tap (outlet/power strip).
  • A loose fitting outlet can cause the plug to overheat or cause a fire. Be sure plug fits tight in the outlet.
  • If there is a loose fit between the plug and the socket or the plug becomes very hot, the socket may need to be replaced. Check with a qualified electrician to replace the socket.
INSTRUCTIONS
  • It is normal for the plug and cord to feel warm to the touch. A plug or cord which becomes hot to the touch or becomes distorted in shape may be a result of a worn electrical outlet. Worn outlets or receptacles should be replaced prior to further use of the heater. Plugging the heater into a worn outlet / receptacle may result in overheating of the power cord or fire.
  • The output of this heater may vary and its temperature may become hot enough to burn exposed skin. Use of this heater is not recommended for persons with a high sensitivity to heat or an inability to react to avoid burns. should be replaced prior to further use of the heater.Plugging the heater into a worn outlet / receptacle may result in overheating of the power cord or fire.
  • Ensure the heater is on a stable, secure surface to eliminate the potential of tipping it over.
  • Make sure that no pieces of polystyrene or other packaging material have been left between elements of the appliance. It may be necessary to pass over the appliance with a vacuum cleaner.
  • Do not attempt to modify or repair the product by yourself. Doing so could void the warranty and cause damage or personal injury. Only a repair technician may disassemble or repair this product.
  • Choking hazard – This remote control unit contains a small battery. Keep the remote control away
    from children and do not swallow the battery. If the battery is swallowed seek medical advice at once.
  • If the machine is not working as it should, has received a sharp blow, has been dropped, damaged,
    left outdoors, or dropped into water, do not use and contact Customer Support.

NOTE: There may be a trace of smoke or odor when the unit is first operated. This indicates that a drop of oil fell on the heating coil during the manufacturing process. It will quickly evaporate and should not re-occur.

IMPORTANT – This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to rig this safety feature.

Package Contents

  • 1 x Oil-Filled Heater
  • 1 x Remote Control 4 x Casters
  • 1 x Thank You Card
  • 1 x User Guide

Product Diagram

 Dreo-Oil-Filled-Heater -image-1

Caster Setup Instructions

The heater is packaged with the casters unattached. You must attach them before operating the heater to prevent the heater from tipping over. The casters are inside the foam at the bottom of the package.

 Dreo-Oil-Filled-Heater -image-2

 Dreo-Oil-Filled-Heater -image-3

 Dreo-Oil-Filled-Heater -image-4

  • Tip-over hazard.
  • Do not operate without the casters attached.
  • Fire hazard.
  • Operate the heater in the upright position only.
  • Any other position can cause damage to this heater and even a fire hazard.

LED Display

 Dreo-Oil-Filled-Heater -image-5

Control Panel

 Dreo-Oil-Filled-Heater -image-6

Remote Control

 Dreo-Oil-Filled-Heater -image-7

Operations and Functions

Place the heater on a firm, level surface free from obstructions,and at least 3ft. (0.9m) away from any wall or combustible materials.Plug into an appropriate voltage AC 120V outlet, The unit will enter standby mode with a beep and power indicator on red.Your heater is ready for use now.

Power ON/OFF

  • When the unit is plugged in, press on the heater / remote control to turn the heater on with default settings: 95°F and high mode  on the LED display.
  • Press once again to turn the heater off.

Mode / Heat Level Settings
When the unit is on, repeatedly press on the heater to cycle through High -> Medium -> Low -> ECO modes, OR simply press or on the remote control for mode switch.

ECO Mode
When ECO mode is on, the heater will adjust the working mode automatically based on the ambient temperature.

Mute/Unmute
Press on the remote control to turn the buzzer on/off.

Temperature Adjustment
  • When the unit is on, press or on the heater / remote control to adjust the set temperature from 40 to 95°F in 1°F increments.
  • When the ambient temperature reaches the set temperature, the heating element will stop running and
    the indicator will go off.after the unit is turned off, the heater will continue radiating heat for a while because of the unique properties of diathermic oil.
  • When the ambient temperature is lower than the set temperature, the heater will start running
    again.

Timer

  • When the unit is running, press on the heater / remote control to enter timer setting.
  • Press or to select a time (00h-24h) and press again to start the timer.
  • When the timer ends, the heater will automatically shut off and go into standby.

Child Lock
When the unit is on, hold and at the same time for 2 seconds to enable/disable Child Lock.

Other Features

 

Memory Function

 

If you turn off the heater and keep it connected to the power source, the heater will return to its last status (working mode & temperature) once turned on again.

 

Note: not applicable to timer, mute, eco mode and child lock settings.

 

 

Overheat Protection

When the ambient temperature is above 122°F, the heater will stop heating, with 10 beeps and the error code “FF” flashing on the display.
Please unplug it from the power source and power it on again when the ambient temperature drops below 122°F.
 

 

Tip-over Protection

When the heater is tipped over, the heater will shut off automatically.
Please place the heater back on a flat, level and stable surface. Turn it on again.
Display Auto- Dimming 

The display will go dim automatically after 60 seconds if no action is taken by the user.

 

Replacement of Batteries in Remote Control

  1. Remove the battery cover in the direction indicated by the arrow.
  2.  Replace with two new AAA 1.5 batteries. Make sure that the positive(+) and negative(-) terminals are positioned correctly.
  3. Push the battery cover back into place.

 Dreo-Oil-Filled-Heater -image-8

CAUTION:

  • Replace with new batteries of the same type when replacement is required.
  • Remove the batteries when the remote control is unused for long period of time.
  • Do not attempt to dismantle the batteries.
  • Do not dispose the batteries in fire, batteries may explode or leak.

Specifications

ModelDR-HSH005
Input120V~ 60Hz
 

Rated Power

1500W (High)

900W (Medium) 600W (Low)

Remote Control Battery 

AAA 1.5V

Troubleshooting

The following troubleshooting guide addresses the most common problems. If your problem is not listed or still
persists, please contact our Customer Support at support@dreo.com.

ProblemPossible CausesSolution
 

 

 

 

 

 

Malfunction Codes on LED Display

 

E2 – Temperature sensor short circuit

Unplug it from the power source and contact Customer Support.
 

E1 – Temperature sensor open circuit

Unplug it from the power source and contact Customer Support.
 

FF – Overheat Protection (Ambient temperature above 122°F)

Unplug it from the power source and power it on again when the ambient temperature drops below 122°F.
 

Heater does not start

 

Power cord is not properly plugged in.

 

Connect the plug to a powered electrical outlet.

 

Turn the heater OFF,
unplug it and allow it
to cool.
Check and remove
Overheat Protection has been activated.any objects on or adjacent to the heater.
Wait 5-10 minutes
before plugging the
unit back in.
Heater does not start
Ensure that your circuit breaker or fuse
No power is passingis working properly.
through the unit.Ensure your heater is
placed on a flat and
even surface.
 

The set temperature

Make sure the thermostat is set at
is lower than thea higher temperature
ambient temperature.than the ambient temperature.
Turn off the unit and
 

 

The heater suddenly stops during heating

The temperature exceeds the threshold of the thermal cutoff.unplug it from the power outlet. Allow it to cool, and then plug it into the electrical outlet again.
The heater is tippedPlace it on a flat, level
over.and stable surface.

REFERENCE

https://www.dreo.com/support/product/dreo-pilot-pro-tower-fan

https://www.dreo.com

Buy Related Product on Amazon

Buy on Amazon

Leave a Reply