Sharper Image-Power-Washing-Showerhead-Feature

Sharper Image Power Washing Showerhead User Manual

Sharper-Image-logo

Sharper Image Power Washing Showerhead User Manual

Sharper Image-Power-Washing-Showerhead-IMG

Specs

Battery: 1800 mAh Lithium Ion
Frequency Range: 100hz-20Khz
Speaker: 40mm x 2
Speaker Power: 3W x 2
Supports Bluetooth®: 5.1
Weight: 520 g.
Size: 158 x 95 x 91mm

Sharper Image-Power-Washing-Showerhead-Fig1

What’s in the Box

Sharper Image-Power-Washing-Showerhead-Fig2

Quick Start Guid

For more detailed installation instructions and how-to videos, go to install-shower-power.ampere.shop or scan the QR code below.

Sharper Image-Power-Washing-Showerhead-Fig3

Before you begin, identify your shower fitting. 

Fixed

The showerhead attaches to a fitting that comes straight from the wall at an angle. The fitting is male and the showerhead is female.

 

Sharper Image-Power-Washing-Showerhead-Fig4

Rain

The showerhead attaches to a fitting that comes straight down from the ceiling. The fitting is male and the showerhead is female.

Sharper Image-Power-Washing-Showerhead-Fig5

*Installation is basically the same for handheld and rain.

Handheld

The showerhead attaches to a hose that comes from a fitting lower down on the wall. The hose is female and the showerhead is male.

Sharper Image-Power-Washing-Showerhead-Fig6

Tip

You can install Shower Power on either end depending on your preference. It can be at the base of the hose OR at the end of the hose, attached to the showerhead.

Sharper Image-Power-Washing-Showerhead-Fig7

Step 1 – Unbox Shower Power and remove the speaker from the dock

Rotate the speaker 90 degrees counterclockwise to separate it from the dock. Set the speaker and dock aside.

Step 2 – Remove your showerhead from the fitting

Unscrew the showerhead. You can usually do this by hand but may need a pair of pliers if it was installed too tightly.

Step 3 – Install the male-male connector on the appropriate side

Sharper Image-Power-Washing-Showerhead-Fig8

Determine which side of Shower Power is input and which side is output. There is a sticker that indicates the input side (this can be removed after the first use). For additional confirmation, an future checks, the hole on the input side is smaller. As such, the turbine will be more visible on the output side.

Rain and Fixed

For these shower types, the male-male connector will go on the output side (the side that connects to the showerhead). First, screw in the male-male connector by hand and then tighten it with the hex key.

Handheld

For these shower types, the male-male connector will go on the input side (the side that connects to the hose). First, screw in the male-male connector by hand and then tighten it with the hex key.

Step 4 – Connecting your showerhead to the shower dock

Attach your showerhead to the shower dock. Connect securely but don’t overtighten. If you noticed that your showerhead/fitting already used sealing tape, you may want to use it at this stage of the installation process.

Tip for handheld showers

If the showerhead is not oriented in the direction you want then you can add a rubber O-ring inside the output threads on Shower Power. Use the thinner rings for smaller adjustments and the thicker rings for larger adjustments. You can use multiple if necessary.

Step 5 – Connect shower dock + showerhead to the shower fitting

Finally, connect the shower dock, with the showerhead now attached, to the shower fitting.

Tip for rain and fixed showers

If the showerhead is not oriented in the direction you want then you can add a rubber O-ring inside the output threads on Shower Power. Use the thinner rings for smaller adjustments and the thicker rings for larger adjustments. You can use multiple if necessary.

Step 6 – Connect the speaker (aka Droplet Pro) to the shower dock

Align the bump in the underside of the shower dock with the groove on the top of the speaker (Droplet). The Ampere logo will be facing the same direction as flow of water when and you should feel the bump go into the groove. Then, rotate the speaker 90 degrees. You will feel it “lock” into place and the Ampere logo will be perfectly centered along the side of Shower Power.

Sharper Image-Power-Washing-Showerhead-Fig9

Troubleshooting

It’s leaking! What do I do?

The first thing to check is if you screwed in Shower Power tight enough. The next solution is to try adding rubber O-rings to the female ends of the connection. Another solution is to use the included thread sealing tape to make the connection tighter. Wrap the sealing tape around the threads in a counterclockwise direction for a better seal.

What do I do if Shower Power is not pointed in the direction I want?

If the showerhead is not oriented in the direction you want then you can add a rubber O-ring inside the output threads on Shower Power. Use the thinner rings for smaller adjustments and the thicker rings for larger adjustments. You can use multiple if necessary. You can also use the included thread sealing tape to prevent leakage and screw to your preferred direction.

Using Shower Power

Charging

Hydroelectric Charging:

Charging a Bluetooth speaker has never been easier–all you have to do is take a shower. Shower Power will charge whenever there is flowing water. Under “normal use conditions,” Shower Power will never need to be charged. We consider “normal use conditions” to be water pressure between 30-50 PSI, water temperature of less than 120°F (50°C), and only using Shower Power while the water is running. If you use Shower Power without water running, then you will be using the reserve battery power.  Continued use will result in needing to use the USB-C port to charge the Shower Power.

USB-C Charging:

Remove Droplet (the speaker) from the Shower Dock and make sure it is completely dry before plugging in. You can charge Droplet with almost any adapter from a reputable brand. Droplet is compatible with QC and PD adapters.

Low Power Notifications:

When the battery level reaches 20% Shower Power will beep three times. When the battery reaches 10% it will beep three times. When you hear this “low battery” sound, we recommend not using Shower Power without water running. Alternatively, you can use the USB-C port to bring it back up to 100%.

Pairing

  • When Shower Power is turned on, it will enter Bluetooth pairing mode automatically. The “searching sound” will play for one minute but it will remain in pairing mode for three minutes. If no device is paired within three minutes, Shower Power will automatically turn off.
  • To pair your device, open the Bluetooth pairing tab on your device and select “Shower Power.” Play your favorite audio from your device. You can pause, play, skip, change volume, etc from your device, via the button pad, or the Shower Power remote control.

Button Pad

Sharper Image-P0ower-Washing-Showerhead-Fig10

Sharper Image-Power-Washing-Showerhead-Fig11

Shower Power Accessories

  • Droplet/Droplet Pro
    When sold with the Shower Dock, the speaker and Shower Dock together are called Shower Power (and Shower Power Pro). When purchased separately, the speaker component is referred to as Droplet (and Droplet Pro). Regardless of whether you bought the speaker component as part of “Shower Power” or separately, it will work with any Shower Power Shower Dock.
  • TWS Pairing
    Before pairing your device, turn on two Ampere speakers (Droplet, Droplet Pro, Shower Power, Shower Power Pro) and allow the two speakers to connect. When they connect successfully, you’ll hear a pairing sound. Single press the pairing button to enter TWS pairing mode. After two speakers are connected, single press on one to disconnect it. After disconnecting the TWS, if you would like to re-pair, turn Droplet off and turn on again.If you are having trouble getting the speakers to  connect, make sure that there are no devices nearby that have paired to either speaker. If so, go into your Bluetooth settings and “forget” all Shower Power-related Bluetooth devices. If you are still having trouble connecting two speakers, hold down the pairing button for ten seconds to reset the Bluetooth pairing settings. You’ll hear a “reset” sound. Then, turn off both speakers. Turn them back on and press the bluetooth button once on both speakers.
  • Shower Power Remote
    The Shower Power remote works just like the button pad on Shower Power itself. If it’s hard to reach, the remote allows you to control all the functionality from up to 10 meters away. The only difference is that the power button on the remote does not turn Shower Power on. Shower Power will turn on automatically when water starts to flow.

Cleaning and Care

  • Just like any showerhead, over time, the Shower Dock may become stained or dirty. This could be a buildup of limescale, or metals and minerals (like iron and manganese), or bacteria. It is fine to clean the Shower Dock with the same cleaners that you use for your showerhead. That could include vinegar, baking soda, or gentle bathroom cleaning spray.
  • Before you begin, remove the speaker (Droplet) from the speaker dock and set it aside. When cleaning the shower dock, pay close attention when cleaning the inside as not to damage the pogo pins. Be very careful with any cleaning agents around the pogo pins and try to keep them as dry as possible.
  • To clean the speaker component (Droplet), remove it from the speaker dock and clean with a damp cloth. Do not leave the pogo pin connection wet or submerged in water.

Warnings

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 20mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out.

CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

The product shall only be connected to a USB interface of version USB 2.0 Adapter shall be installed near the equipment and shall be easily accessible. The plug considered as disconnect device of adapter The device complies with RF specifications when the device used at 20mm form your body This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference

  • this device may not cause harmful interference, and
  • this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the  equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference

  • this device may not cause harmful interference, and
  • this device must accept any interference received, including interference that may cause undesired operation

REFRENCE LINK

https://www.sharperimage.com/view/product/Power+Washing+Showerhead/208166

Leave a Reply