Bird-X Peller® Pro Electronic Bird Repeller User Manual
INSTALLATION
Important safety-related information:
- a) Do not install the device during rain or snow conditions.
- b) Installation shall be made in such a way that a power supply and the internal part of the control unit never be subjected to water or snow.
- c) Note that the power supply is intended for dry location use only.
- Point the unit toward the bird infestation. Expect maximum coverage of approximately 1 acre in a long dispersion pattern. St the unit on a flat surface c mount it to a wooden post using the mounting bracket and screws (included).
- Plug one end of the AC adapter into the POWER jack (located on the back of the unit). Plug the adapter into any standard electrical outlet. An optional battery cable may be used to connect the control unit to a 12-volt battery. If this is done, first connect the black battery clip to the negative terminal on the battery and then connect the red battery clip to the positive terminal. Both the connection to the electrical outlet (or battery) and the connection of the power cable inside the control unit must be prTurn the power switch (located in the upper right-hand corner of the faceplate) to INT/EXT. SPKR (ON position). (NOTE: The unit may take a couple of seconds before starting). Adjust the volume to the desired level. After turning the unit OFF, be certain to wait AT LEAST 60 SECONDS before turning it back on. Close the cover and latch shut. Ensure that the cover is properly latched closed and do not open the cover during rain or other conditions that would expose the inside of the control unit to water. protected from dripping or splashing water. Do not set an object filled with liquids on the control unit.
Continued
- Set the DIP switches located on the front metal faceplate of the unit, (see Switch Array #1 and Switch Array #2) to the desired settings. See the section “Programming your BirdXPeller PRO” for specific programming information.
- Turn the volume switch to LOW (Minimum).
- Turn the power switch (located in the upper right-hand corner of the faceplate) to INT/EXT. SPKR (ON position). (NOTE: The unit may take a couple of seconds before starting).
- Adjust the volume to the desired level.
- After turning the unit OFF, be certain to wait AT LEAST 60 SECONDS before turning it back on.
- Close the cover and latch shut. Ensure that the cover is properly latched closed and do not open the cover during rain or other conditions that would expose the inside of the control unit to water.
PROGRAMMING YOUR BIRDXPELLER
To program your BirdXPeller PRO unit you will need a small screwdriver, toothpick, or other pointed, rigid object to move the switches in the switch array (see FIG. 1). The switch arrays are the switch hanks located in the bottom right-hand corner on the
faceplate (inside the clear front cover). A switch is ON if the switch is moved to the right-hand side. The switch is OFF if the switch is moved to the left-hand side.
BIRD RECORDING SETTING SWITCHES
The Bird Recording Switches are the first eight switches (FIG. 2) in Switch Array #1. Each switch has a recording number to the left of it that corresponds with the bird descriptions listed on the foil label inside the cover on the front of the unit they are as follows:
- Pigeon I
- Pigeon Il/Bird Predator I
- Starling/Pigeon III
- Sparrow
- GullI
- Gull II
- Bird Predator II
- Bird Predator III
For best results, choose a combination of both predator calls AND bird distress recordings to create the most natural scenario.
MODE SETTING SWITCHES
The Mode Setting Switches are the last five switches (FIG. 3) in Switch Array #2. These set the various modes of operation: such as the amount of time between playing bird distress calls, when the unit will operate (day only, night only, or 24 hours), and whether the unit will operate in the random mode or normal mode.
DELAY SWITCHES
The two “Delay” or Time-Off Switches are located just below the Recording Switches (1-8) in the switch array (FIG. 4). The unit will delay a number of seconds or minutes between recorded sounds when the unit is set to one of the various Time-Off Modes. The TEST setting is appropriate for testing but is NOT recommended for long-term success. Please note that the unit will play all of the selected recordings (either sequentially or non-sequentially, depending on the Random Mode), then it will go into a delay.
The time the unit stays off depends on the Time-Off and the Random Mode Settings. If the unit is operating in Random Mode, the unit will delay anywhere from the minimum value to the maximum value for that Time-Off setting. If the unit is not in Random Mode, it will delay only the minimum value.
VOLUME CONTROL
The unit has a volume control dial on the front panel of the unit. Turning the dial toward LOW will reduce sound output and rotating the dial toward HIGH will increase sound output.
CAUTION:
Take care when turning the dial since the unit may be in an inactive state when the dial is rotated. It could then reactivate at a very high level of sound which could be painful to your ears.
POWER SWITCH (INT/EXT. SPKR)
The power switch enables the unit to operate. Slide the switch to the INT/EXT. SPKR (ON) position to start the unit. This will operate the unit, and generate sound out of the unit AND out of an optional extension speaker at the same time. If you wish to operate ONLY a remote extension speaker (optional), then move the switch to the EXT. SPKR ONLY position.
If you turn the unit OFF, be sure to leave it off for about 30 seconds before turning it back on to allow the electronics to properly reset. To fully disconnect the unit, unplug the power adapter from the electrical outlet or disconnect the battery cable from the 12-volt battery.
Successful Long-Term Behavior Modification
Product success takes time to build. Bird and pest habits may take several days or weeks to break. Follow all suggestions for maximum efficacy. “Instant” tests do not replicate natural conditions and give no indication of the unit’s success with the infestation.
Prepare for Successful Bird Control
Bird-X, Inc. has been recognized worldwide as the bird control x-parts for 40 years. We have become experts through extensive experience and research. As a result, we are happy to analyze problems and make recommendations based on each customer’s specific situation and needs. In addition, we provide the following recommendations for the greatest success, even before activating the repeller. Remove inducements. Clean the area of all evidence of birds: nests, fledglings, droppings, dead birds, and the residential scent.
Because birds and their droppings can carry many diseases, use extreme caution when removing them. Do not breathe or come into direct contact with them. If you have questions about how to do this safely, consult an expert. (Adult birds are likely to return to their young in order to protect them or to assist them in leaving the area.) Remove food spillage and garbage. nesting material and other appealing items.
Limited Warranty
This BirdXpeller Pro unit is warranted against defects in material and workmanship for six months from the date of purchase (extended warranty available). Bird-X will replace or repair, provided the defect occurs under normal use. Returns are accepted only with authorization from our Chicago office.
