Monster Pure DNA Fit Bluetooth Earbuds User Manual
Please Note:
This Bluetooth earpiece shall be charged by the supplied charging unit only.
Caution:
The batteries in this product are not replaceable. During use, storage, or transportation the battery should not be subjected to extremely low temperatures or low air pressure at high altitudes. If the batter is exposed to extremely high temperatures it could result in an explosion or the leaking of flammable liquid or gas. Please take care when disposing of the unit: disposal in a fire, oven, or mechanically crushing or cutting machine could cause an explosion.
Warning:
Do not dispose of the unit in fire or water. Never attempt to disassemble and reassemble. Waste electrical products should not be disposed of with household waste, please recycle where facilities exist. Check with your local authority for recycling advice. Keep your device and all accessories out of the reach of children and animals. Small parts may cause choking or serious injury it swallowed. avoid exposing your device to very cold or very hot temperatures (Below 00 or above 450 C).
Extreme temperatures can cause deforming of the device and reduce the charging capacity and life of the vour device. Do not allow your device to get helicoids can cause serious damage. do not hancio vour device with wot nanos. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth& SIG. Inc. IPhone. iPad and Mac a trademarks of Apple Inc. registered in the U.S. and other countries.
Product Specs:
- Model No: Monster DNA Fit
- Version: 5.2 Bluetooth& Chipset
- Support profiles: A2DP/AVRCP/HFP/ HSP/SPP
- Frequency response: 20hz-20kHz
- Impedance: 320
- Driver size: 13mm
- Sensitivity: 12243d8
- Audio coding formats: CVSD, mSBC, SBC, APT-X.
- AAC SNR: > 98dB
- Effective range: up to 10 meters
- Earbud battery capacity: 2 x 50mAh
- Playing time: 7-8 hours (with ANC: 5-6 hours)
- Charging case battery capacity: 500mAh
- Earbud charging time: Max. 1.5 hour
- Charging case charge time: Approx. 1.5 hours
- Charging port: Type-CT
- Input voltage: DC5.OV / 14
- Ingress protection: IPX5 (Earbuds only)
- Wireless charging: Yes
Monster DNA FIT
Earphone Function Operation Power on:
When you take the earphones out of the charging case, the earbuds will automatically power on. alternative lait the earbuds are cowered off. press and hold the (MB) button for 2 seconds and they will power ON Power oft: Put parches cack into the charging case and ensure the case is powered they will be automatically powered OFF, Or you can press and hold the (MFB) button on either earphone or y seconds both earphones will de turned oFF.
Toggle ANC/Transparency Modes:
Press either the “MF8” button twice to cycle 1. ANC On 2. Transparency On 3. ANC Off Play/Pause: Press the (MFB) button once or when the vendor Previous Track: Press and hold the “Volume for seconds Next Track: Press and hold the “Volume + Volume Jp.
Answer Call:
Press either “MIFE button once. (if answering a call while on another call, the ill be placed on hold) Reject Call: Press and hold either “MB” button twice. End Call: Press either “MF8* button once. Activating Phone Assistant: ess citie (does not work during a call) Pairing: For first-time use pairing – take the earbuds out of the case and they will automatically enter Bluetooth8 pair It the earbuds are disconnected from the device. the ear All go into pairing mode automatically. If the earbuds are already connected to a device. press the (MFB) button for 3.
Bluetooth® Pairing:
Go to “Bluetooth” Setting on your Bluetooth® device (Phone, Tablet, etc.) Turn the Bluetooth& ON, on your device. Open the case and remove the earbuds and they will automatically enter Bluetooth® pairing mode. Make sure that the earbuds are not already paired to another device. On your Bluetooth device, select the pairing name of your earphones on the list of available devices, The pairing name is Monster DNA Fit.
Troubleshooting tip
If the earphones do not connect to your device, turn the earphones OFF, turn your device’s Bluetooth& OFF and then back ON, then repeat the pairing process. Your earphones are designed to automatically sync to each other when they are turned ON, however if they ever fail to sync. please put both earphones back into the charging case and try a factory reset. Factory Reset: Place both earbuds in the case.
Press and hold the “Charging Case” Button for 15 seconds until the LED indicator flashes red and green. LEDs will flash red and green three times, then the factory settings will be restored. Delete the device from your phone’s Bluetooth list Phone Calls: If there is an incoming call on your Bluetooth® device, the earphones will pause the playback and ring to alert you of the call.
Charging the Case
Connect the USB-C™ charging cable to the socket on the charging case. Plug the cable into a standard USB-C™ 5V / 1A output. (The indicator will flash red or green depending on the battery level once the charging cord is disconnected.) *If you do not have a USB-Ci I WAII adapter or available computer USB-C7 port, there are USB-C7 ferale to Use- male caio ers avando ed vounoca consumer electronics re dies The LED indicator on the case will pulse red while charging when the case is between 0%-50% battery power.
The LED indicator will pulse green when the case is between 50%-99% battery power. The LED indicator on the case will have a steady green LED when it is 100% charged. You can also charge your case via a wireless charger pad; a full charge will take around Shours Warning: To avoid damage to the charging case, please only use a 5V / lA charger. Charging the Earphones: To charge the earbuds, place the earbuds into the case. The LED on the earbuds will pulse with a white color.
When fully charged, the LEDs will turn off. Note – the case LED will not operate when charging the earbuds. (Note the earphones come with a built-in rechargeable battery. Before using them for the first time, we recommend you fully charge the battery. A full charge takes approximately 1 hour). Warning: The earphones can only be used with the provided ChareIne case.
Checking the Case’s Battery Level:
Open the case, and press the case’s button once:
- 0-10%: red LED flashing
- 10%-50%: red LED pulse 5 seconds
- 50%-99%: green LED pulse 5 seconds
- 100%: green LED solid light 10 seconds;
Quick Guide
Green Light:
Greenlight will pulse to indicate that the case is charged above 50% unit lit reaches loon at which point the case sDw chow a sold green LED
Red Light:
The red light will pulse to indicate that the case has less than 50% power remaining. The red LED will flash red to indicate the remaining case After the first time you pair your earbuds, they will automatically reconnect to your device when removed from the case, providing your device is near and the coin function is enabled. In order to achieve the best possible Active Noise Cancellation (ANC). make sure that the ear tips are snug in your ears. We include several size ear tips to make sure you have the best fit possible. If either the left or right side disconnects, please place both earbuds back into the charging case to reset them.
