YAMAHA R-N2000A Network Receiver User Guide

YAMAHA R-N2000A Network Receiver User Guide

PREPARATION

Checking the included accessories
Check and make sure that you have all the following items

Items marked with * are not explained in this guide. See the User Guide for more information. Be sure to fill in the correct date of purchase and the name of the store of purchase in the warranty, and then keep it in a safe place.

This guide requires the following items
Have the following items on hand, in addition to the product.

1. This is used for connecting to the Internet in your home.
2. Have one ready that is already connected to your wireless router.

Items marked with * are not required in some cases. Have them ready if needed.

Connecting Speakers
Connect the speakers as illustrated. Connect a subwoofer if needed

1. Peel back about 10 mm of insulation from the end of the speaker cable and twist the core wires tightly.
2. Turn the knob of the speaker jack to the left to loosen it, and insert the core wires of the speaker cable into the hole of the jack.
3. Turn the knob back to the right to tighten it.

Flipping up the wireless antenna

Flip up the wireless antenna as illustrated.

NOTICE

• Do not exert excessive force on the wireless antenna. Doing so may damage it.

Connecting the power cord
Connect the included power cord.

OPERATION

Turning the power on
Turn the product on.

Put the z (Power) switch in the up position to turn the power on.
The power indicator lights up.

After the following message appears on the front display, press RETURN on the front panel to clear the message. It may take about 30 seconds for the message to appear. The portion shown as * differs depending on the device. After the following message appears on the front display, press RETURN on the front panel to clear the message. It may take about 30 seconds for the message to appear. The portion shown as * differs depending on the device.

Wireless WAC Display The WAC (Wireless Accessory Configuration) function is for applying the wireless settings of an iOS device to another device and wirelessly connecting to the network. Because it is explained on a later page how to connect to networks with the MusicCast Controller app, how to cancel WAC is explained here.

Automatic adjustment of speaker settings (YPAO)

Use the included YPAO microphone and run YPAO. YPAO is a function that detects speaker connections and the distance from the listening position, then automatically adjusts the speaker settings, such as volume balance and tone.

Turn your subwoofers on and adjust the volume to its midpoint.
If the crossover frequency can be adjusted, set it to the maximum.

This step is not necessary if a subwoofer is not connected.

Put the included YPAO microphone in the listening position and connect it to the YPAO MIC jack on the front panel.

The following message appears on the front display.

NOTE
Secure the YPAO microphone in place so it does not move. If a camera tripod is used for the microphone, its screws can be used to secure the microphone.

Press SELECT on the front panel to start the automatic adjustment of speaker settings with YPAO.
Adjustment starts automatically after about 10 seconds. It takes about 1 minute. Do not make any unnecessary noise until the adjustments are complete.

Check the results on the front display. After all adjustments are complete, the results are shown on the front display. Follow the instructions that are displayed, and use the SELECT buttons to complete adjustments.

If there are no errors or warnings:

If an error message or warning message appears on the display, refer to the User Guide.

Save the YPAO results.
Check the following display, and press SELECT to save the adjustment results.

To cancel or readjust (Retry), turn SELECT to choose the desired item.

Remove the YPAO microphone from the YPAO MIC jack.
After checking the following display, disconnect the YPAO microphone.

This completes the YPAO settings.

Configuring network settings.

After installing the dedicated smart-device app, “MusicCast Controller”, connect the product wirelessly to your
network from the screen of the app

1. Prepare your smart device. Refer to the Wi-Fi settings of the smart device and confirm that it is connected to the network of your wireless router.
2. Install the “MusicCast Controller” on your smart device.
   Search for “MusicCast Controller” on the App Store or Google Play to download the app.
3. Start the app and start configuring settings as directed by the app.

NOTE

• You can also connect to the network via a wired connection. See the User Guide for more information.
• If you want to cancel the configuration before it is complete, press RETURN on the front panel.
• If the connection fails, quit the app, and then try again from Step 3.

Playing Internet radio
Use the app to confirm that you can play Internet radio.

1. Select “Net Radio” on the app’s screen.
   
2. If you are connected to the Internet, a list of Internet radio stations appears. If it does not appear, reconnect to the Internet.
3. Choose the desired station.
   Choose the desired station from the list of Internet radio stations.
4. Adjust the volume.
   Adjust with the volume slider in the app. You can also adjust it with VOLUME on the front panel.

This completes the initial setup. For detailed explanations of how to connect various external devices or to configure advanced settings of the product, refer to the User Guide.

REFERENCE LINK

https://usa.yamaha.com/products/audio_visual/hifi_components/r-n2000a/index.html