Feit Electric SEC3000 LED Smart Security Flood Lights With Camera Guide
LED Smart Security Flood Lights With Camera
WARNING:
This product may represent a possible shock or fire hazard if improperly installed or attached in any way. The product should be installed following the owner’s manual, current electrical codes, and/or the current National Electric Code (NEC).
- J-Box (not included)
- Mounting Bar
- J-Box Screws (2 pieces)
- Spacers (2 pieces)
- Mounting Gasket
- Mounting Plate
- Terminal Block
- Mounting Plate Screws (2 pieces)
- Mounting Bar Screw (1 piece)
- Fixture Body
- Mounting Holes
- Rubber Washers (2 pieces)
- Decorative Nuts (2 pieces)
- LED Flood Lights
- Camera Lens and Photocell Sensor
- Speaker
- Motion Sensor
- Mic
- Indicator light
PARTS INCLUDED (not drawn to scale)
ADJUSTING FIXTURE
RESETTING THE UNIT & ACCESSING THE SD CARD
To access the Reset Button and microSD™ card, remove the cover using a small screwdriver (included). To reset the unit, (the unit must be connected to power) press the Reset Button for 15 seconds or until you hear an audible tone. To remove the microSD card, push the card in with your finger and release it. The card will eject halfway.
PRE-INSTALLATION
Remove the Mounting Plate (6) by unscrewing and removing the Decorative Nuts (13) and Rubber Washers (12).
EXTERNAL J-BOX INSTALLATION
- Turn the main power Off at the circuit breaker or fuse box.
- Install Mounting Bar (2) to an External J-Box (1) using provided J-Box Screws (3). Add Spacer (4) to eliminate gap between the Mounting Bar and the Mounting Plate. NOTE: Spacer (4) may or may not be needed.
- Extend and feed J-Box wires through openings on the Mounting Gasket (5) and Mounting Plate (6).
NOTE: Tear away at perforation on Mounting Gasket (5) - Secure Mounting Gasket (5) and Mounting Plate (6) to Mounting Bar (2) using Mounting Bar Screw (9). Do not over-tighten.
- Connect power supply wires directly to Terminal Block (7). Secure wires to Terminal Block by using a small flat-head screwdriver. See detail. CONNECT Black wire to”L” input. Ground wire to “GND” input. White wire to “N” input.
- Position and align the Mounting Holes (11) on Fixture Body (10) to the Mounting Plate Screws (8). Secure Fixture Body (10) to Mounting Plate (6) using Rubber Washers (12) and Decorative Nuts (13).
- Turn the power On at the circuit breaker or fuse box. Turn On the wall switch if connected to one. Ensure lights work before proceeding to step 8.
- Once the fixture is tightly secured to J-Box, apply silicone sealant around the base of the fixture to prevent moisture from reaching the connections.
FLUSH J-BOX INSTALLATION
- Turn the main power Off at the circuit breaker or fuse box.
- Install Mounting Bar (2) to a Flush J-Box (1) using provided J-Box Screws (3). Add Spacer (4) to eliminate the gap between the Mounting Bar and the Mounting Plate. NOTE: Spacer (4) is only needed if J-Box is recessed too deep.
- Extend and feed J-Box wires through openings on the Mounting Gasket (5) and Mounting Plate (6).
NOTE: Do not tear away at perforation on Mounting Gasket (5) - Secure Mounting Gasket (5) and Mounting Plate (6) to Mounting Bar (2) using Mounting Bar Screw (9). Do not over-tighten.
- Connect power supply wires directly to Terminal Block (7). Secure wires to Terminal Block by using a small flat-head screwdriver. See detail. CONNECT Black wire to”L” input. Ground wire to “GND” input. White wire to “N” input.
- Position and align the Mounting Holes (11) on Fixture Body (10) to the Mounting Plate Screws (8). Secure Fixture Body (10) to Mounting Plate (6) using Rubber Washers (12) and Decorative Nuts (13).
- Turn the power On at the circuit breaker or fuse box. Turn On the wall switch if connected to one. Ensure lights work before proceeding to step 8.
- Once the fixture is tightly secured to J-Box, apply silicone sealant around the base of the fixture to prevent moisture from reaching the connections.
- POSITION MOTION SENSOR AND CAMERA
For optimal performance, the base of the motion sensor should be placed parallel and 9 feet above the ground. The camera can be angled in a different direction than the lights.
TROUBLESHOOTING TIPS – Q & A
The camera will not connect to my Wi-Fi network
- Make sure the LED is blinking blue. If the LED is blinking red, you will need to press and hold the Reset Button located behind the cover on the side of the camera (see the Resetting Unit & Accessing SD Card section).
- Make sure the Wi-Fi network is a 2.4GHz network, device will not connect to a 5GHz network.
- Test your Wi-Fi network with other devices such as your phone or computer to make sure it is operating properly.
- The Wi-Fi connection may be out of range during pairing. Use your phone to check the range, it is recommended to have at least 2 signal bars showing for proper connection.
- Your Wi-Fi network password is case-sensitive, make sure you are entering it correctly.
The camera is off-line
- There could be a temporary issue with your internet connection (e.g., service disruption). Please try again in a few minutes.
- Make sure your Wi-Fi router is turned On.
- The camera may not have power to it, make sure the wall switch and breaker is in the On position.
- Cycle the power Off and On. You will hear an audible tone and the status LED should blink red then to a solid blue in about 1 minute. If it does not turn blue after a minute, please go through the setup process again to reconnect to your Wi-Fi signal.
- Make sure the camera is getting a good signal from your Wi-Fi router. Use your phone to check the range, it is recommended to have at least 2 signal bars showing for proper connection.
- The camera may have been disconnected from your Wi-Fi network, press and hold Reset the Button (see the Resetting Unit & Accessing SD Card section) until you see a blinking blue LED and hear an audible tone.
Live video stream is slow to load
Camera streaming issues may be caused by any of the following:
- Your phone’s cellular connection, which is reliant on mobile coverage and signal reception is slow.
- Limited internet bandwidth at home, for example, other video streaming services running at the same time on your network can cause congestion slowing down the internet upload and download speeds.
- Wi-Fi reception may not be stable or work reliably if the camera’s Wi-Fi signal strength is less than 2 signal bars. You may need to install a Wi-Fi repeater or extender to boost the Wi-Fi signal.
The camera is not recording?
- Make sure the Record Switch is turned On in the app, under SD Card Settings. This is located in the Settings menu in the upper right corner of the control panel.
- Make sure that the microSD card is installed correctly. To confirm the camera is recognizing the microSD card, go to the SD Card Settings in the Settings menu and make sure microSD Card Capacity menu shows Total Capacity, Used and Free Space. If this does not appear you may consider reformatting the microSD card. WARNING: Reformatting the microSD card will delete all videos stored on card. Please go through the troubleshooting section before doing so or contact our Customer Support Team.
FCC Rules.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).
- The device has been evaluated to meet general RF exposure requirements.
- The device can be used in portable exposure conditions without restriction.
- The device can be used in mobile (min 7.87 in.) exposure conditions without restriction.
Limited Warranty
This product is warrantied to be free from defects in workmanship and materials for up to 1 year from the date of purchase. If the product fails within the warranty period, please visit feit.com/help for instructions on replacement/refund or call 866.326.BULB. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED
Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.
