Eufy Security Space View Baby Monitor User Manual
WHAT’S IN THE BOX
FEATURE INTRODUCTION
Monitor Features:
- Volume controls
- Screen
- Power button
- Press to switch on / off the monitor screen
- Press and hold for 2 seconds to power on / off
- Menu button
- Navigation buttons
- OK button
- Press to confirm the selection
- Press to switch camera display if more than 2 cameras added
- Return to previous level of menu / Talk button
- Press and hold to speak to the camera
- When menu is opened, press to return to the previous level of menu
- Monitor Antenna
- Support stand
- Micro USB charging port
- LED indicator
- Red: charging
- White: Fully charged
- Microphone
- Speaker
Camera Features:
- Standard camera lens 4 Speaker
- Microphone 5 Micro USB port
- Power LED Status indicator 6 Pairing button
SETTING UP THE CAMERA AND MONITOR
Charge the Monitor
Fully charge the monitor before use. To charge:
- Connect one end of the micro USB cable to the baby monitor, and the other end to the power adapter.
- Plug the adapter into a power outlet.
- Press and hold the power button for 2 seconds to turn the baby monitor on.
Charge the Camera
- Connect one end of the micro USB cable to the baby camera, and the other end to the power adapter (5V 2A)
- Plug the adapter into a power outlet.
The new baby monitor and camera will set up automatically. You are all set to use the products after monitor and camera are charged.
ADDING A CAMERA TO THE BABY MONITOR
The baby camera and baby monitor are paired out of the box. Refer to the following steps when adding extra baby cameras or after resetting a baby camera. Make sure the baby monitor’s version is the same as the baby camera’s.
- Enter menu settings, go to Camera -> Add Camera, then follow onscreen instructions to start the pairing.
- Press and hold the pairing button on the rear of the camera for 1 second until a notification prompt is heard.
When more than 2 cameras are added, you can manually switch among cameras. Press the OK button, the screen will be switched to the next camera’s screen. The icon of the camera you select will appear. You can also select the “Cycle Camera” option. The screen cycles through the list of connected baby cameras according to preset intervals.
When the volume is set to high, monitor will emit a loud noise if placed close to the camera. This is a normal phenomenon and can be resolved when camera is moved away from the monitor.
PLACING THE CAMERA (WALL MOUNT & CORNER MOUNT)
- Use the monitor to test the viewing angle from your desired mounting spot.
- Mark the screw holes with a pencil.
- Drill 1/5” holes into the wall and then insert the anchors into the holes.
- Insert the screws through the mounting holes of the wall mount and screw into the anchors.
- Place the camera on the wall mount.
You can select the way you like to install the camera.
MONITOR MENU SETTINGS
Press and hold the power button to power on the monitor. Press the menu button to open Menu Settings.
The interval duration between each sound alert is 30 seconds. It will not alert during this interval even if there is alert trigger condition.
Menu option is subject to change without notice.
On-screen Menu Icons
REPLACING THE CAMERA LENS
NOTICE
Warning
Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.For the declaration of conformity, visit the Web site https://www. eufylife.com/. This product can be used across EU member states. Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so called power USB is prohibited. A statement regarding the AC/DC adapter as disconnect device is missing in the user manual. The statement shall require a socket outlet that is installed near equipment and that shall be easily accessible. The adapter shall be installed near the equipment and shall be easily accessible. Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for T8300-M and accessories is -20°C 45°C. The suitable temperature for T8301-C and accessories is -20°C-40°C. When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 5°C~25°C.
This product is designed and manufactured with high quality materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DOWNLOAD PDF LINK
