SUNBEAM SFH7112 Heater Calefactor User Manual
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
- Read all instructions before using this heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Always unplug the heater when not in use.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions has been dropped, or is damaged in any manner. Discard the heater, or return it to the authorized service facility for examination and/or repair.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
- . Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from the traffic area so that it will not be tripped over.
- To disconnect the heater, turn the controls off, then remove the plug from the outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Always plug heaters directly into a wall outlet/ receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
- When unplugging, be sure to pull by the plug and not the cord.
- If the heater will not operate, see specific instructions on Auto Safety Shut-off.
- DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user-serviceable parts. All servicing should be performed by qualified personnel only.
- Discontinue use if the plug or outlet is hot. It is recommended that the outlet be replaced if the plug or outlet is hot to touch.
- The heater must not be located immediately below a socket outlet. Do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool.
ASSEMBLY INSTRUCTIONS
TECHNICAL SPECIFICATIONS
- Amps: 12.5
- Wattage: 1500W (+5% –10%)
- Working voltage: 120V AC/60Hz
NOTE: Low Heat setting may be 1000W on some models.
ASSEMBLY INSTRUCTIONS NOTE:
A Phillips screwdriver is required for assembly. Unpack your heater from the box, being careful to remove all parts from plastic bags and remaining packaging. Please save the carton for off-season storage. Some models are packed with separate bases and pedestals in the box. Carefully remove all parts from plastic bags. To prevent scratches, place all parts onto a cloth before assembly. Follow the below instructions for Pedestal/Base assembly:
Pedestal Assembly (if no pedestal is included in this model, move to Base Assembly)
- Step 1: Run the power cord through the center of the assembled pedestal. Snap the pedestal into the bottom of the heater housing. Refer to Figure 1,2. Insert the alignment post from the heater housing into the hole on the pedestal for proper alignment.
Base Assembly
- Step 1: If the base is in two halves, snap them together by sliding slots of one base half into slots of the second base half. Refer to Figure 3.
- Step 2: Run the power cord through the center of the assembled base. To assemble the base to the unit first make sure the side marked “Rear” is facing the back of the heater. Insert the alignment posts from the pedestal into the alignment holes on the base for proper alignment. Line up holes of the base with holes on the bottom of the pedestal (or heater housing if no pedestal is included), and secure with 4 provided screws. Refer to Figure 4.
- Step 3: Lace the power cord through the cord minders on the underside of the base. Refer to Figure 5. Step 4: Turn the heater right side up on a flat level surface before beginning operation.
FEATURES – OPERATIONS
OPERATING INSTRUCTIONS
- Make sure the unit is in the OFF ( ) position before plugging the heater into the outlet.
- Place the heater on a firm, level surface.
- Plug the heater into a standard outlet. Once plugged in, the Power Light will illuminate.
NOTE: Remove the plastic film from the control panel before using (if included). NOTE: Avoid overloading your circuit by not using other high-wattage appliances in the same outlet. At 1500 watts, this unit draws 12.5 Amps. Mode Control Turn the Mode Control to the desired setting.
If you want to shut off the heater at any time during operation, turn the Mode Control to the Off ( ) position. Power Light will remain lit until the heater is unplugged.
CLEANING MAINTENANCE
CLEANING/MAINTENANCE Always unplug the heater before cleaning and allow the heater to cool down.
- Clean the unit with a soft cloth moistened with a mild soap solution.
- NEVER use abrasive or flammable solvents to clean the unit.
- After cleaning, be sure to completely dry the unit with a cloth or towel.
- Store the heater in a cool, dry location.
- It is recommended that you store the unit in its original carton. TIP: Over time, dust may accumulate on the front grills. This can be removed by wiping the unit with a damp cloth.
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically advanced safety system that requires the user to reset the heater if there is a potential overheating situation. When a potential overheating temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit
RESET INSTRUCTIONS
If your heater shuts down:
- Turn Control to OFF ( ).
- Unplug the unit and wait 30 minutes.
- Plug in and operate normally
FOR MODELS WITH TIP-OVER PROTECTION
(Not applicable for SCH700/SFH700 and SCH800/SFH800 series heaters) Tip Over Shut-Off: When the unit is accidentally knocked over, it will instantly shut off. The unit may also shut off if it is moved or bumped. To reset, simply place the heater in an upright position and it will operate normally. NOTE: If the unit does not turn on when placed in the upright position, turn the Mode Control to the desired heat setting and the heater will resume operation.
TROUBLESHOOTING
General Information:
Environmental Factors – Many factors will affect your desired comfort level. These factors can include insulation, open or drafty doors and windows, and outside temperature. Please check and take action if any of these potential problems are affecting your heaters’ ability to adequately warm your room. Supplemental Heat – Portable electric heaters are intended for supplemental heating of rooms to heat the room in and turn down the central heat thermostat. They are not intended to replace central heating systems. Do NOT attempt to repair or adjust any electrical or mechanical functions on this heater. Doing so will void the warranty. The inside of the heater contains no user-serviceable parts. All servicing should be performed by qualified personnel only.
If you have any questions regarding your product or would like to learn more about other Sunbeam® products, please contact our Consumer Service Department at 1-888-264-9669 or visit our website at www.sunbeam.com.
Troubleshooting for your Heater
Trouble | Probable Cause | Solution |
• Heater Does Not Turn On. | ☛ Tip-over switch engaged (only applicable on models with tip-over protection). ☛ Manual user reset is activated. ☛ Not plugged in properly. ☛ Electrical outlet does not hold plug in securely. ☛ Thermostat set too low. ☛ Obstruction causing the heater not to operate. ☛ Circuit breaker trips. | ✔ Set heater upright on a level surface. ✔ Follow reset instructions listed in this manual. ✔ Ensure plug is properly inserted. Make sure electrical outlet and circuit breaker are working. ✔ Have outlet replaced by a licensed electrician. ✔ Turn Thermostat Control clockwise until the heater restarts. ✔ Unplug the heater and remove all obstructions. Position your heater 36 inches (91cm) away from all objects. ✔ Make sure no other high wattage appliances are operating on the same circuit and reset breaker if needed. |
• Not Enough Heat. | ☛ Heater is in Low Heat or 1 setting. ☛ Thermostat set too low. | ✔ Change setting to 2 (High Heat). ✔ Turn Thermostat Control clockwise until the heater restarts. |
• Heater Cycles ON and OFF Frequently. | ☛ The thermostat automatically turns the heater on and off to maintain selected comfort level. | ✔ To make this occur less frequently adjust the thermostat control clockwise to the highest setting. |
• Heater is Blowing Cold Air. | ☛ Mode Control is set to Fan only setting. | ✔ Turn Mode Control to the 1 (Low Heat) or 2 (High Heat) setting. |
• Fan Speed Doesn’t Change. | ☛ High Heat and Low Heat settings control the heat output of the heater and not the fan speed. Fan runs at the same speed on all settings. | ✔ Run heater in the “2” setting (High Heat) for maximum heat output. |
• Unexpected Noise. | ☛ You may hear a popping or crackling sound as the heater heats up. This is normal and safe operation. Once the heater heats up, the crackling sound will go away. | ✔ If the noise persists call Sunbeam® at 1-888-264-9669. |
• Unexpected Smell. | ☛ There may be an odor or vapor coming from the heater the first time you use it or after prolonged or seasonal storage. | ✔ This is normal and is the result of dust or other debris accumulating on the heating element. Make sure the heater is in a well ventilated area and continue running until the odor or vapor goes away. |
1-YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if, in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for one year from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component. If the product is no longer available, a replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty. This warranty is valid for the original retail purchaser from the date of the initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance.
JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or in any way change the terms and conditions of this warranty. This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair, or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover Acts of God, such as fire, flood, hurricanes, and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied, or statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. JCS disclaims all other warranties, conditions, or representations, express, implied, statutory, or otherwise. JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential,
or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against the purchaser by any other party. Some provinces, states, or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state, or jurisdiction to jurisdiction.
REFERENCE LINK
https://s7d9.scene7.com/is/content/NewellRubbermaid/DASH/S7_int/2020/SFH811_43_40149874.PDF