DYMO SP5 5 lb Digital Postal Scale User Manual

DYMO SP5 5 lb Digital Postal Scale

Digital Postal Scale

Your new Digital Postal Scale weighs items up to five pounds (2.2 kg) in 0.1 ounce (1 g) increments. This User Guide provides instructions for using the scale.

Unpacking the Scale
The scale is shipped with a protective ring under the scale platform. You must remove this ring before using the scale.
To unpack the scale

1.  Unpack the scale.
2.  Set the scale on a firm, flat surface.
3.  Remove the protective ring from under the scale platform.
4.  Remove the protective film from the scale display.

Inserting the Battery
The scale uses one 9-volt alkaline battery.

To insert the battery

1.  Turn the scale over.
2.  Remove the battery compartment cover.
3.  Insert a 9-volt battery into the battery
   compartment as shown.
4.  Make sure to insert the battery correctly. Inserting the battery backwards can damage
   the scale and cause smoke or burning.
5.  Replace the battery compartment cover.
   Remove the battery if the scale will not be used for a long period of time.

Turning On the Power
The scale has an Auto Shut Off feature which turns the scale off automatically after thirty seconds of inactivity. You can turn off this Auto Shut Off feature.

To turn the scale on

•  Press the ON/TARE button on the front of the scale. When the scale is first turned on, wait a few seconds for the scale to stabilize before weighing items. The display shows 0.0 when ready.

To turn the scale off

•  Press the OFF button on the front of the scale.

To turn off Auto Shut Off

1.  Make sure that the scale is off.
2.  Press the ON/TARE button.
3.  When the display shows SP5, press the oz/g button.
4. The display shows SHOF and then 0.0 when ready. The scale now remains on until manually turned off.
5. Turning off the Auto Shut Off feature is temporary. You need to repeat this procedure each time you turn on the scale.

Weighing an Item

Always wait for 0.0 to display before placing an item on the scale platform.
After placing an item on the scale, wait for several seconds for the weight to appear. When the scale is ready, a o appears in the upper-left corner of the display.

To weigh an item

•  Place an item on the scale platform.

Using the Tare Feature
You can weigh small items or items that cannot be easily placed on the scale platform by placing the items in a container and using the Tare feature to eliminate the weight of the container. Pressing the ON/TARE button always returns the scale to zero.

To use the Tare feature

1.  Place an empty container on the platform.
2.  When the scale is ready, press the ON/TARE button.
   The display is set to zero.
3.  Place the items to be weighed in the container.
   The display shows the weight of the items, without the weight of the container.
4.  After removing the container, press the ON/TARE button to reset the scale to zero.

 Changing the Units of Measure

Your scale can display weight in English (pounds) or metric (kilograms) units. The default unit of measure is English.

To change the units of measure

•  Press the oz/g button to toggle between English and metric units.

Caring for the Scale
With proper care and handling, your scale will give you years of service. Keep the following in mind when using your scale:

•  Your scale works best when operated and stored at normal room temperature. Avoid lengthy exposure to extreme heat or cold.
•  Only operate the scale on a stable, vibration free surface.
•  Exposure to dust, dirt, moisture, vibration, and air currents; and proximity to other electronic equipment can affect the   reliability and accuracy of your scale.
•  Using the scale in proximity to wireless devices, such as mobile phones, can cause the scale display to fluctuate when the device   is in use.
•  Although this scale is designed to be quite durable, gently place items to be weighed on the platform. Avoid rough treatment, as   this may permanently damage the internal sensor and void your warranty.
•  You can permanently damage the scale by placing significantly overweight items on the scale platform.
•  Avoid shaking, dropping, or otherwise shocking the scale. This is a precision instrument and
  MUST BE HANDLED WITH EXTREME CARE.
•  The scale has been calibrated at the factory and will not need to be calibrated again.

Technical Specifications

For information about our other scale products, visit www.dymo.com.

Troubleshooting

Warranty

Your DYMO® Scale comes with a warranty against defects in materials, design, or workmanship, for one year from the original date of purchase, when used in accordance with all operating instructions. Normal wear and tear is not covered, nor is excessive use, abuse or damage caused by a user either intentionally or accidentally.

EXCEPT AS PROVIDED HEREIN, DYMO MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, AND DYMO SPECIFICALLY
EXCLUDES WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. DYMO’S LIABILITY UNDER
THIS WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE SCALE. DYMO SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER OR NOT FORESEEABLE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY.

In the event of a product failure, please visit www.dymo.com/support or contact DYMO Technical Support to obtain a Return Material Authorization (RMA) number and further instructions to return your product.

Declaration of Conformity – FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity – Industry Canada
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions; (1) this device digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions;

1.  this device may not cause harmful interference, and
2.  this device must accept any interference received, including interference that may cause undesired operation.

DOWNLOAD PDF LINK

https://download.dymo.com/dymo/user-guides/Scales/Pelouze/SP5_UserGuide_en-US.pdf