Polar Speed Sensor Bluetooth Smart User Manual

Polar Speed Sensor Bluetooth Smart User Manual

INTRODUCTION

Polar Speed Sensor is designed to measure speed and distance when cycling. The sensor is compatible with devices that support Bluetooth® Cycling Speed Service. You can use your sensor with dozens of leading fitness apps, as well as with Polar products using Bluetooth® technology. Check the compatible products at support.polar.com/en.

The latest version of this user manual can be downloaded at support.polar.com/en

GET STARTED

SPEED SENSOR PARTS

1. Speed sensor (pictures 1 A and 2 A)
2. Spoke magnet (picture 2 B)

INSTALLING THE SPEED SENSOR

To install the speed sensor and spoke magnet, you need cutters and a cross-head screwdriver.

1. It is recommended to install the speed sensor on the front fork of your bicycle (as in picture 1 A).
2. Attach the rubber part to the speed sensor (picture 3).
   
3. Pass the cable ties over the speed sensor and rubber part (picture 2 A). Adjust the sensor to the front fork so that the POLAR logo faces outwards. Adjust the ties loosely. Do not tighten them fully yet.
4. Attach the magnet to a spoke at the same level as the speed sensor (picture 2). There is a small caved dot on the backside of the sensor (picture 3 A), which indicates the spot the magnet should be pointing at when passing the sensor. Fasten the magnet to the spoke and tighten it lightly with a screwdriver. Do not tighten it fully yet.
5. Fine-tune the positioning of both the magnet and the speed sensor so that the magnet passes close to the sensor but does not touch it (picture 2). Move the sensor towards the wheel/spokes as close as possible. The gap between the sensor and the magnet should be under 4 mm/0.16’’. The gap is correct when you can fit a cable tie between the magnet and the sensor.
6. Rotate the front tire to test the speed sensor. The flashing red light on the sensor indicates that the magnet and the sensor are positioned correctly. If you keep rotating the tire, the light will stop flashing. Tighten the screw to the magnet with a screwdriver. Also, tighten the cable ties securely and cut off any excess cable tie ends.

Before you start cycling, set the wheel size of your bicycle into the receiving device or mobile application.

PAIRING
Your new sensor must be paired with the receiving device to receive data. For more information, see the user guidance material of the receiving device or mobile application. To ensure a good connection between the sensor and the receiving device, it is recommended to keep the device in a bike mount on the handlebar.

IMPORTANT INFORMATION

CARE AND MAINTENANCE
Keep the sensor clean. Clean it with a mild soap and water solution, and rinse off with clean water. Dry it carefully with a soft towel. Never use alcohol or any abrasive material, such as steel wool or cleaning chemicals. Do not immerse the sensor in water. Your safety is important to us. Make sure the sensor does not disturb pedaling or using the brakes or gears. While riding your bike, keep your eyes on the road to prevent possible accidents and injury. Avoid hard hits as these may damage the sensor. Replacement magnet sets can be purchased separately.

CADENCE SENSOR BATTERY
The battery cannot be replaced. The sensor is sealed to maximize mechanical longevity and reliability. You can purchase a new sensor from the Polar online store at www.polar.com or check the location of the nearest retailer at www.polar.com/en/store-locator. The battery level of your sensor is displayed on the receiving device if it supports Bluetooth® Battery Service. To increase battery life, the sensor goes into standby mode in thirty minutes if you stop cycling and the magnet is not passing the sensor.

FREQUENTLY ASKED QUESTIONS

What should I do if the cadence reading is 0 or there is no cadence reading while cycling?

• Make sure the position and distance of the cadence sensor to the crank magnet are appropriate.
• Check that you have activated the cadence function in the receiving device. For further information, see the user guidance material of the receiving device or mobile application.
• Try keeping the receiving device in a bike mount on the handlebar. This may improve the connection.
• If the 0 reading appears irregularly, this may be due to temporary electromagnetic interference in your current surroundings.
• If the 0 reading is constant, the battery may be empty.

..there are irregular cadence or heart rate readings? 

• Disturbance may occur near microwave ovens and computers. Also, WLAN base stations may cause interference when training with the Polar Cadence Sensor. To avoid erratic reading or misbehaviors, move away from possible sources of disturbance.

I want to pair the sensor with the receiving device before installation.

• Follow the instructions in the user guidance material of the receiving device or mobile application. Instead of rotating the crank, activate the sensor by moving it back and forth close to the magnet. The flashing red light indicates that the sensor is activated.

TECHNICAL SPECIFICATION

Operating temperature:

• -10 °C to +50 °C / 14 °F to 122 °F

Battery life:

• Average 1400 hours of use.

Accuracy:

• ±1 %

Material:

• Thermoplastic polymer

Water resistance:

• Splash proof

FCC ID: INWY6
Speed Sensor Bluetooth QD ID: B021136 Copyright © 2021 Polar Electro Oy, FI-90440 KEMPELE. All rights reserved. No part of this manual may be used or reproduced in any form or by any means without prior written permission of Polar Electro Oy. The names and logos marked with a ™ symbol in this user manual or the package of this product are trademarks of Polar Electro Oy. The names and logos marked with a ® symbol in this user’s manual or the package of this product are registered trademarks of Polar Electro Oy. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Polar Electro Oy is under license.

REFERENCE LINK

https://www.polar.com/en/products/accessories/speed_sensor_bluetooth_smart