Shark SV1107 Rotator® Freestyle User Guide

Shark SV1107 Rotator® Freestyle User Guide

IMPORTANT SAFETY INSTRUCTIONS

1. DO NOT use or charge the unit outdoors.
2. DO NOT use or charge the unit on wet surfaces.
3. DO NOT immerse the vacuum cleaner, charging base, or charging adapter in water or other liquids.
4. DO NOT handle the vacuum, charging base, or charging adapter with wet hands.
5. DO NOT use the charging adapter if the power cord has been damaged.
6. DO NOT abuse the charging adapter cord. NEVER carry the charging adapter or charging base by the cord.
7. DO NOT unplug the charging adapter by pulling on the cord; to unplug, grasp the plug, not the cord.
8. DO NOT use a charging adapter with an extension cord. Plug the adapter directly and only in a standard (120V., 60Hz) electrical outlet.
9. DO NOT run the vacuum over the charging adapter cord.
10. Keep the charging adapter cord away from heated surfaces.
11. DO NOT attempt to use this charging adapter with any other product nor attempt to charge this product with another charging adapter.
12. Only use the charging adapter provided with the vacuum. It is marked “For SV1100 series models only”.
13. Always turn the vacuum off before connecting or disconnecting the motorized floor brush.

ASSEMBLY

VACUUM COMPONENTS

• A Main Body
• B Handle
• C Screw
• D Dust Cup
• E Dust Cup Release
• F Upper Dust Cup Door Release
• G Lower Dust Cup Door Release
• H Motorized Brush
• I Power Button
• J Charging Adapter
• K Charging Base

ASSEMBLY

1. Insert the vacuum body into the motorized brush. (fig. 1a)
2. Insert the handle pole into the top of the main body. (fig. 1b)
3. Use a screwdriver to secure the handle assembly in place with the bolt (taped to the handle during shipping). (fig. 1c)
4. Ensure that the dust cup is securely in place. (fig. 1d)

CHARGING

1. The charge adapter plug will fit into the charging base only one way. Insert the charging adapter plug by aligning the arrow on the plug with the arrow next to the charging jack on the back of the charging base. (fig. 2)
2. Place the vacuum on the charging base to charge. Charge the unit for 6 hours before using the vacuum for the first time. (fig. 3)
3. This unit is equipped with a precision charger that monitors the batteries to ensure a full charge for every use and to extend the life of the batteries. Depending on usage, the time for a full charge is 3 to 6 hours.
4. One-half of the blue LED light around the power button will illuminate while the unit is charging. When the charge is complete, the complete oval will be illuminated for one (1)hour. (fig. 4) After one (1) hour, the LED light will turn off but the unit will remain fully charged.

USING YOUR SHARK ® CORDLESS VACUUM

• Place your foot lightly on the top of the motorized brush and tilt the handle back to release the unit from the locked upright position.
• Lightly press the power button on the motorized floor brush with your foot to turn the vacuum on to a high speed optimized for carpet cleaning. In this setting, the vacuum will run for approximately 15 minutes.
• Press the button again to switch to a lower speed optimized for bare floor cleaning. In this setting, the vacuum will run for approximately 21 minutes. The LED lights around the power button will indicate your speed.
• Press the button again to turn the unit off.

IMPORTANT:
The indicator light around the power button will flash if the brush roll stops due to a jam. This feature is designed to protect the Lifetime Belt that powers the brush roll.

MAXIMIZING THE LIFE OF YOUR BATTERY

1. To enhance battery life, this vacuum is equipped with an advanced feature that will shut off the vacuum when the battery is almost fully discharged. If the vacuum shuts off while in use, charge the unit until the complete oval around the power button is illuminated, indicating a full charge.
2. Charge the vacuum for 6 hours before initial use. After initial use, each recharge will take 3 to 6 hours. A complete oval around the power button will illuminate when the charge is complete.
3. The precision charger monitors the batteries so you don’t have to. A complete charge can take as little as 3 hours but may take up to 6 hours because the charger monitors battery properties to extend battery life. Leaving the unit in the charger past the complete charge time will NOT harm the batteries.
4. If the vacuum has never been used or has not been used for an extended period of time, it will take 3 to 5 complete charge and run-down cycles to realize the full operational time of the vacuum.
5. Do not store or charge in areas of high temperature or humidity.
6. Use only the charge adapter supplied with this unit, marked with “For SV1100 series Models Only”. If other chargers are used, the battery can fail causing damage to the battery, to the vacuum, or to personal property.

BATTERY REMOVAL, REPLACEMENT, AND DISPOSAL

The cordless vacuum is powered by Ni-Mh batteries, which must be recycled or disposed of properly in accordance with state, federal, and local laws. If uncertain as to how to remove the battery pack, we suggest that you take your vacuum to a reputable small appliance service technician to have this service performed.

BATTERY REMOVAL 

1. Ensure that the unit is Off.
2. Never open the battery compartment except to replace or dispose of the battery pack.
3. The battery door is on the bottom of the floor nozzle. Turn the unit over and push the sliding tab located next to the battery door to the unlock position. Slide and lift the battery door off of the nozzle.
4. Remove the battery pack by pulling on the battery strap.
5. Grasp the white connector terminals and push down on the lever with your thumb. Pull to disconnect.

BATTERY REPLACEMENT 

1. Push the connector terminals together until they click into place.
2. Replace the new battery pack into the battery compartment, taking care to tuck the wiring completely in so that the wiring does not interfere with the battery access door.
3. Place the battery door onto the bottom of the nozzle, slide it back into place, and move the sliding tab next to the door to the lock position.

CARE AND MAINTENANCE

EMPTYING THE DUST CUP
To maintain the best performance of your vacuum, empty the dust cup after every use or as debris approaches the “MAX FILL” line. Never operate the vacuum without the dust cup and filter in place.

1. Turn off the vacuum before removing the dust cup.
2. Press down on the dust cup release button (fig. 5) and pull out the dust cup.
3. Holding the carry handle, place the dust cup inside a trash receptacle and press the lower dust cup door release button. Gently tap the dust cup to dislodge and release dust and debris. (fig. 6) Important: If the Dust Cup Door does not swing open after pressing the release button, push the door open using the bottom door tabs.
4. Snap the door back in place.
5. If you notice the hair or other debris wrapped around the metal screen in the upper chamber of the dust cup, press the upper dust cup door release to open the top of the dust cup. Lift out the metal screen, clear any debris, and replace it. Snap the door back into place. (fig. 7)
6. Replace the dust cup by first seating the lower part of the dust cup, then pushing in the top part until it clicks. (fig. 8)

CLEANING THE FILTER

Your vacuum has a high-efficiency dust cup to maintain strong suction by preventing debris from collecting on the filter. To maintain strong suction, it is important to clean the foam filter every month, under normal use.

1. Turn off the vacuum and remove the dust cup.
2. Remove the foam filter (fig. 9) and rinse under water until the water runs clear. (fig. 10) Squeeze the excess water out of the filter and let it air dry for 24 hours before replacing it.

NOTE:
It is normal for your foam filter to discolor over time; it will not affect the filter performance.

BRUSH BAR REMOVAL 

1. For easier cleaning, the brush roll can be removed from the nozzle. Using a coin, turn the dial next to the brush roll access door to the unlock position. (fig. 14) Remove the brush roll access door. (fig. 15)
2. Slip the black belt off of the white gear and lift out the brush roll. (fig. 16)

BRUSH BAR INSERTION

1. To reinsert the brush roll, first slip the black belt onto the white gear (fig. 17a), then align the white square on the opposite side of the brush roll into the square slot. (fig. 17b)
2. Align the white square on the belt side and position it into its slot. (fig. 18) 3 Replace the door, inserting the wheel side first. Use a coin to move the dial to the lock position.

RESTARTING AFTER A JAM
If the indicator light around the power button flashes, the brush bar has jammed and will cease to operate.

1. Turn the unit off and allow it to cool down for 10 seconds.
2. Ensure that nothing is blocking the motorized brush or wrapped around the brush bar.
3. Turn the power on and the unit should operate normally.

TROUBLESHOOTING GUIDE & REPLACEMENT PARTS

REFERENCE LINK

https://support.sharkclean.com/hc/en-us/articles/4402199356690-SV1107-Series-Shark-Rotator-Freestyle-Owner-s-Guide

DOWNLOAD LINK

Shark SV1107 Rotator® Freestyle User Guide