ROCATT Syn Pro Air Wireless Gaming Headset User Manual
PACKAGE CONTAINS
HEADSET CONTROLS
LED INDICATIONS
Connection Status LED
- Solid White = Headset Connected
- Pulsing Red = Low Battery
- Solid Red = Headset Charging
- Pulsing White = Headset On/Full Battery
- Double Blink White = Headset Pairing
Connection Status LED
- Solid White = Headset Connected
- Double Blink White = Headset Pairing
- Pulsing Red = Microphone Muted
CHARGING
The Elo 7.1 Air uses a 24+ hour rechargeable battery. Make sure to charge it regularly.
Headset Storage
Always charge your headset before storing it for any extended period of time (greater than 3 months). Never store the unit in temperatures above 113°F/45°C.
USB-A COMPATIBILITY
The ELO 7.1 Air also works great with other platforms with USB-A ports, including the PS5 & PS4 and Nintendo Switch, in docked mode.
- Plug the Transmitter in a USB-A on your device
- Hold the Power Button for 2 seconds to turn on the headset
- In your device’s settings, make sure the Elo is selected on your device.
When connecting the transmitter to a PS5 or PS4, the master volume must be adjusted from the Settings Menu. *Software capabilities are only available on PCs.
PC/MAC® SETUP
- Plug the Elo 7.1 Air Transmitter into a USB slot on your PC
- Hold the Power Button for 2 seconds to turn on the headset (the transmitter and headset are automatically paired)
- Right-click the speaker icon in your toolbar and select “Open Sound Settings”
- Select “Elo 7.1 Air” from the “Choose Your Output Device” drop-down menu
- Open the driver software to customize your settings.
TECH SPECS
- Direct wireless connection via USB-A transmitter
- 20Hz – 20kHz speaker frequency response
- 2.4GHz transmitter frequency response
- Audio controls: power button, master volume wheel, mic mute, mic monitor wheel
- Rechargeable 24h battery (average 1+ week playtime based on typical ~3h use per day)
- 50mm speakers with neodymium magnets
- Removable unidirectional microphone
- Leatherette headband with foam cushioning
- Over-ear design featuring memory foam
SYSTEM REQUIREMENTS
- Windows® 7, 8, and 10 (software support)
- USB 2.0 (or higher)
- Internet connection (for driver software)
Should you need assistance … Our support team is ready to help you with any technical questions. Just send an e-mail to support@roccat.com or visit our website at: WWW.ROCCAT.COM/SUPPORT
REGULATORY COMPLIANCE STATEMENTS FOR THE ELO 7.1 AIR RX & TX
LOCAL RESTRICTIONS ON RADIO USAGE Caution:
Due to the fact that the frequencies used by wireless devices may not yet be harmonized in all countries, these radio products are designed for use only in specific countries and are not allowed to be operated in countries other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country of use.
Any deviation from the permissible power and frequency settings for the country of use is an infringement of national law and may be punished as such. To determine whether you are allowed to use your wireless network device in a specific country, please check to see if the radio type number that is printed on the identification label of your device is listed in the manufacturer‘s OEM Regulatory Guidance document at the following URL http://www.turtlebeach.com/homologation or contact Turtle Beach directly.
FEDERAL COMMUNICATIONS COMMISSION (FCC) COMPLIANCE NOTICES
This section includes the following FCC statements for the Elo 7.1 AIR:
- FCC IDs: XGB-TB18140 & XGB-TB15143
- Class B Interference Statement
- RF Radiation Exposure & Hazard Warning
- Non-Modification Statement
CLASS B INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF RADIATION EXPOSURE & HAZARD STATEMENT
To ensure compliance with FCC RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.) from all persons. Using higher gain antennas and types of antennas not covered under the FCC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
NON-MODIFICATION STATEMENT
Use only the supplied internal antenna. Unauthorized antennas, modifications, or attachments could damage the Elo 7.1 AIR RX & TX Models and violate FCC regulations. Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment. Please contact Turtle Beach for a list of approved 2.4 GHz antennas. This product is compliant with the Consumer Product Safety Improvement Act of 2008, Public Law 110-314 (CPSIA)
RF RADIATION EXPOSURE & HAZARD STATEMENT
To ensure compliance with RSS-102 RF exposure requirements, this device must be installed in a location such that the antenna of the device will be greater than 2 cm (0.8 in.) away from all persons. Using higher gain antennas and types of antennas not covered under the IC certification of this product is not allowed. Installers of the radio and end users of the product must adhere to the installation instructions provided in this manual. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
REFERENCE LINK
https://www.roccat.com/products/syn-pro-air-headset