KLIPSCH The Three-II Best Wireless Shelf Stereo User Manual
INSIDE
- DC Power Cord
- 3.5mm AUXILIARY
- USB Cable
- Remote Control
CONTROLS
- Power Switch
- Source
- Volume Dial
REMOTE CONTROL
- Power ON/OFF
- Volume Up
- Track Backward
- Play/Pause
- Bluetooth
- Phono
- Mute
- Track Forward
- Volume Down
- Auxiliary
- LED Lights ON/OFF
POWER SWITCH
POWER ON / STANDBY
- PRESS ONCE TO POWER ON
- PRESS AGAIN TO ENTER STANDBY MODE
POWER OFF
SOURCE CONTROL DIAL
BLUETOOTH® WIRELESS TECHNOLOGY
PAIR
- Phone White / Flashing
Example only. Your device may differ.
CONNECTIONS – ANALOG RCA – INPUT
CONNECTIONS – TURNTABLE – INPUT
CONNECTIONS – USB AUDIO – INPUT
CAUTION:
Install the dedicated driver software before connecting the computer to this unit via USB. For instructions about driver installation procedures, please access the support section of the web page http://www.klipsch.com/heritage-wireless
FACTORY RESET
DISCONNECT POWER
PRESS and HOLD while RE-CONNECTING POWER
*NOTE* Factory Reset will clear the Bluetooth® pairing history.
CARE AND CLEANING
- USE MICROFIBER CLOTHS ONLY
IMPORTANT SAFETY INSTRUCTIONS!
- READ these instructions.
- KEEP these instructions.
- HEED all warnings.
- FOLLOW all instructions.
- DO NOT use this apparatus near water.
- CLEAN ONLY with a dry cloth.
- DO NOT block any ventilation openings. Install per the manufacturer’s instructions.
- . DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- DO NOT defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
- PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.
- To completely disconnect this apparatus from the AC Mains, disconnect the power supply wall wart from the AC receptacle.
- The mains plug/appliance coupler is used as a disconnect device, the disconnect device shall remain readily operable.
- DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or fire.
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to a person
WARNING:
Do Not Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel. Place the equipment near a main power supply outlet and make sure that you can easily access the power breaker switch.
This product is intended to be operated ONLY from the AC Voltages listed on the back panel or included power supply of the product. Operation from other voltages other than those indicated may cause irreversible damage to the product and void the product’s warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate. If the product is equipped with a detachable power cord, use only the type provided with your product or by your local distributor and/or retailer. If you are unsure of the correct operational voltage, please contact your local distributor and/or retailer.
EU COMPLIANCE INFORMATION
Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2014/35/ EU; European Union EMC Directive 2014/30/ EU; European Union Restriction of Hazardous Substances Recast (RoHS) Directive 2011/65/ EU; European Union WEEE Directive 2012/19/ EU; European Union Eco-Design Directive 2009/125/EC; European Union Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) Directive 2006/121/EC;
European Union Radio Equipment Directive (RED) 2014/53/EU. Hereby, Klipsch Group Inc. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You may obtain a free copy of the Declaration of Conformity by contacting your dealer, distributor, or Klipsch Group, Inc.’s worldwide headquarters. Contact information can be found here: http://www.klipsch.com/Contact-Us
WEEE NOTICE:
This mark applies only to countries within the European Union (EU) and Norway. This appliance is labeled per European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling. W52 and W53 bands are restricted to indoor
FCC EMC COMPLIANCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital Device. Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this device.
FCC WIRELESS TRANSMITTER COMPLIANCE INFORMATION
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
CANADA EMC COMPLIANCE INFORMATION
Innovation, Science and Economic Development Canada statement: This device complies with ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation.
CANADA WIRELESS TRANSMITTER COMPLIANCE INFORMATION
Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
