TaoTronics TT-AD002 Aroma Diffuser User Manual
Product Diagram
- Mist Nozzle
- Cover
- Base
- LIGHT Button
- MIST Button
- DC Socket
- Air Inlet
- Max Water Level Line
- Air Outlet
- Essential Oil Tube
Package Contents
- 1 x TaoTronics Aroma Diffuser (Model: TT-AD002)
- 1 x Power Adapter
- 1 x Cup
- 1 x User Guide
Specifications
Model
Operate Voltage
Power
Water Tank Volume
Working time
Max Humidity Increase
Ultrasonic Frequency
TT-AD002
DC 24V
13W max
300 ml / 10 oz
8 hours max
About 30 ~ 70 ml / 1 ~ 2 oz per hour
2.4 MHz
How to Use
Caution
- Please add water to the tank first, then pour essential oils up to the marking on the tube or until dispensing starts. If there’s no fragrance, the water-oil balance may be off. Please add enough essential oil as instructed then.
- If you are using a glass essential oil tube, please handle with care to avoid breakage.
- It is recommended to use purified or distilled water.
Add and Drain Water
- Remove the tank cover, add water into the tank no higher than the max water level line. Drizzle a few drops of essential oil into the tube until dispensing starts. Put the tank cover back on.
- Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside the tank.
Operations and Functions
Connect to a power source. Once connected the diffuser will enter standby mode. Please make sure there is enough water inside the tank.
Power On
Press the Mist Button to turn on the unit. Change the Mist Output Press and hold the Mist Button to enter high mist with one beep and low mist with two beeps.
Change the Light Color
- Press the Light Button once to automatically cycle through different colors.
- Press again to stay on the current color. Keep pressing to cycle through all the colors. When the cycle is done, press one more time to turn off the light.
- Or press and hold the Light Button for 2-3 seconds to turn off the light.
Set the Timer
When the mist is on, press the Mist Button to set 1 / 3 / 6 hour timer or turn off the timer. The timer indicator will light up accordingly. When the ON indicator is on, the timer is off.
Power Off
When the timer is off, press the Mist Button once to turn off the unit.
Cleaning the Water Tank
- Unplug the power cord and remove the cover.
- Drain any reaming water from the tank.
- Add some warm water into the tank and mix with mild detergent, wash with a cleaning cloth.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
- Empty the tank from the water outlet.
- Add 3-5g (approx. one teaspoon, based on scale of the residues) baking soda / NaHCO3 to the tank.
- Fill the tank halfway full with warm water (100-150ml / 3.38-5.07floz, 50°C / 122°F), stir it to fully dissolve.
- Soak for 3-5mins, wipe down the tank and tank cover using a small brush or soft cloth with baking soda solution. (For better cleaning, remove the muting cover and wipe it down thoroughly).
- Drain the solution and rinse the tank under tap water.
- Rub the inside and outside dry with a dry towel or clean cloth.
- Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or when the mist output is low due to grime build-up.
- Empty the tank from the water outlet.
- Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh lemon to the tank.
- Fill the tank halfway full with warm water (100-150ml / 3.38-5.07floz, 50°C / 122°F), stir it to fully dissolve.
- Soak for about half an hour.
- Thoroughly clean the grime at the bottom and atomizer (slot at the center) of the tank with a small brush.
- Wipe down tank cover using a small brush or soft cloth with baking soda solution. (For better cleaning, remove the muting cover and wipe it down thoroughly).
- Drain the solution and rinse the tank under tap water.
- Wipe off the soda residues if any.
- Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
- You may use dishwashing detergent when baking soda is unavailable. But it works better for oil removing instead of odor and mineral buildup.
- Do not rinse the base directly with water; try to avoid wetting the buttons, light holes, air inlets and underneath to avoid short circuit.
- It is not recommended to clean the unit with white vinegar since its direct and indirect contact with the atomizer will damage it permanently
REFRENCE LINK
