Taotronics TT-BA09 Pro Bluetooth Wireless Adapter User Manual

Taotronics TT-BA09 Pro Bluetooth Wireless Adapter User Manual

PACKAGE CONTENTS

1. 1 x TaoTronics Wireless Adapter (TT-BA09 Pro)
2. 1 x 3.5mm Audio Cable
3. 1 x 3.5mm Female to RCA Male Cable
4. 1 x Optical Cable
5. 1 x USB-C Charging Cable
6. 1 x User Guide

PRODUCT DIAGRAM

1. A for 1st Device
2. B for 2nd Device
3. Codec Indicators
4. Transmitter (TX) / Receiver (RX) Mode Switch
5. Power ON/OFF/Pairing
6. Power Indicator

BUTTON CONTROL

LED INDICATOR STATUS

Indicators
Power
Indicator AB
SBC
APTX
LL

Function
Power ON
Power OFF
Standby Mode
Battery Low
Charging
Fully Charged
Pairing
Connected
Re-connect
Pairing
Connected
Connected using the SBC codec
Connected using the Apt-X® codec
Connected using the
Apt-X Low Latency® codec Status
Flashing twice
Flashing twice
Flashing every 5 seconds
Solid on
Solid on
Off
Flashing quickly
Solid on
Flashing slowly
Flashing quickly
Solid on
Solid on
Solid on
Solid on

• SBC: SBC codec, supported by most Bluetooth® devices
• APTX: Apt-X® codec, the Bluetooth® device shall support Apt-X® codec. Prior than SBC.
• LL: Apt-X Low Latency® codec, the Bluetooth® device shall support Apt-X low latency®. Prior than SBC and Apt-X®.

HOW TO USE

Charging

• Connect the charging port with any USB charging adapter or active computer USB port.
• The Power indicator will stay solid on during charging. Once fully charged, it will turn off.

Note:

• You can use the adapter during charging, however, there might be background buzz noise.
• We recommend charging the unit for at least 2 hours before using it for the first time.

Use in TX Mode | Initial Pairing

• Successfully paired: “A” solid on, the Codec indicator for the current streaming codec will light up

Note:

• If you want to experience LIP SYNC, make sure your Bluetooth® device supports apt-X Low Latency® codec. After connected, the Codec indicator “LL” will light up to indicate the low latency streaming codec.
• The default input mode is SPDIF. When the AUX cable is plugged in, it will switch to AUX mode automatically.
• Please do not connect TT-BA09 Pro to an amplifier output in TX mode, which may cause over-voltage and damage the adapter.

Pair with the 2nd Bluetooth® Device

Note:

• After connecting with two Bluetooth® devices, the Codec indicator for the highest codec supported by both devices will light up (e.g., if device “A” supports SBC and Apt-X codec, while device “B” supports SBC codec, then Codec indicator “SBC” will light up).
• After disconnecting with one of the devices, the Codec indicator for the highest codec supported by the remaining device will stay on.

• Use in TX Mode | Automatic Re-connect
  TT-BA09 Pro can remember the devices paired previously, and will attempt to pair with the last connected devices (up to 2 devices) automatically once it is turned on.
  Use in TX Mode | Clear Pairing History
  When the adapter is off, clear the pairing history by sliding the Mode switch to “RX”, then power it on.

Use in TX Mode | Use with your TV

Check your TV output options before the set up

• Ensure your TV speaker is set to “External Speaker”.
• Ensure TV audio format is set to “PCM” or “Dolby/DTS” is OFF (This is IMPORTANT).
• Ensure the optical audio cable is plugged in “SPDIF IN” port on TT-BA09 Pro.

Note:

Setting menu may be different depending on different TV brands and models.

TVs with AUX 3.5mm audio out

TVs with RCA audio out (Red/White ports labeled “AUDIO OUT”)

Use in TX Mode | Use with your PC/Laptop

Use in RX Mode | Initial Pairing

Pair with the 1st Bluetooth® Device

• Slide the Mode switch to “RX” mode.
• Press and hold the Power button for 3 seconds to turn on the adapter.
• For the first use, TT-BA09 Pro will enter pairing mode automatically with indicator “A” flashing quickly.
• Activate the Bluetooth® function on your phone/tablet, find “TaoTronics TT-BA09 Pro” in the search results and tap to connect. Once connected, the indicator “A” will turn solid on.

Pair with the 2nd Bluetooth® Device

• After connecting with the 1st Bluetooth® device, press the Power button twice, the indicator “B” will flash quickly.
• Place your 2nd Bluetooth® device close to the adapter (within 3 feet / 1 meter). Activate the Bluetooth® function on your phone/ tablet, find “TaoTronics TT-BA09 Pro” in the search results and tap to connect. Once connected, the indicator “B” will turn solid on.
• Use in RX Mode | Automatic Re-connect
  TT-BA09 Pro can remember the devices paired previously, and will attempt to pair with the last connected devices (up to 2 devices) automatically once it is turned on.
• Use in RX Mode | Clear Pairing History
  When the adapter is off, clear the pairing history by sliding the Mode switch to “TX”, then power it on.

TROUBLESHOOTING

Problem
No audio input
Audio delay
Pair with a new
Bluetooth® device
Can’t reconnect with the last connected device

Solutions
Make sure that you have followed the instructions for cable connections and settings on TV/PC/Laptop.
Make sure your Bluetooth® device supports apt-X Low Latency® codec.
After connected, the Codec indicator “LL” will light up to indicate the low latency streaming codec.
When TT-BA09 Pro is powered on, press the Power button twice to enter pairing mode before reconnecting to the paired device.
Each time you switch the modes, the pairing history will be cleared. Please re-pair with your Bluetooth® device as instructed.

WARRANTY AND SERVICE

Thank you for choosing the TaoTronics TT-BA09 Pro Wireless Adapter. If any problems occur, please contact the TaoTronics Customer Care Centre in your country via the contact information listed in this User Guide.

REFRENCE LINK