XMARTO-Wire-Free-Security-Camera-User-Manual-prduct-img

XMARTO Wire-Free Security Camera User Manual

Views: 102
Table of contents show

XMARTO-DT3034-PTZ-Dome-IP-Camera-User-Guide-Image-1

XMARTO Wire-Free Security Camera User Manual

XMARTO-Wire-Free-Security-Camera-User-Manual-prduct-img

What’s in the Box

DISCLAIMER:
The exact components of your camera, images and quantities may vary depending on your model number. While this QSG will address the setup of your camera.

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-1

NOTE:
For best results, use the included accessories. Third-party accessories may not work properly.

Before You Start

Before setup of the camera, we strongly recommend recharging the camera overnight to make sure it has 100% power.

  1. Use a 5V DC phone charger (not included) and a USB cable (included) to charge the camera.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-2
  2. The indicator blinks in green while charging; the indicator turns off when it’s fully charged.

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-3

NOTE:
Please use only a 5V DC power charger to recharge the camera. Chargers that do not meet the standard may damage the batteries. Please charge the battery at room temperature to avoid damage.

Working Diagram

The camera works standalone

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-4

Pair the camera to WiFi NVR

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-5

Camera Introduction

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-6

Set up the Camera – Work as a Standalone Camera 
Download and Install Application

  1. Download the WallPixel app from the App Store or Google Play Store and install the application on your device. NOTE: Setup is the same for Smartphones and tablets.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-7
  2. Create an account using an email address or phone number as the username; and a password between 6-20 characters.
Add the Camera to the App

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-8

  1. Bring the camera and your smartphone close to your WiFi router.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-9
  2. Open the rubber cover beneath the camera, and hold the ON/OFF button for 2 seconds to turn on the camera. You should hear ‘starting paring’ from the camera, and the indicator blinks in red. That means the camera enters pairing mode.
    NOTE: If the camera did not enter pairing mode, hold the reset button for 5 seconds to bring the camera into pairing mode.
  3. Run Wallpixel APP Tap + to start adding a camera, select camera type Solar/Battery Camera, follow the on-screen guide to setup the camera.

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-10

NOTE

  • The camera works with 2.4G WiFi ONLY.
  • If the camera was not added successfully, press and hold the reset button for 5 seconds and do it again. Make sure to provide a CORRECT WiFi hotspot and password.

Pair the Camera to a WiFi NVR (optional)

If you want to manage cameras and videos from an NVR, you can pair this camera to a compatible WiFi NVR or camera system.

  1. Bring the camera close to your WiFi NVR.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-11
  2. Open the rubber cover beneath the camera, and hold the ON/OFF button for 2 seconds to turn on the camera. You should hear ‘starting paring’ from the camera, and the indicator blinks in red. That means the camera enters pairing mode.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-12NOTE: If the camera did not enter pairing mode, hold the reset button for 5 seconds to bring the camera into pairing mode.
  3. With the NVR connected to a TV/Monitor, click the + icon at the bottom and follow the on-screen guide to pair your camera to the NVR. For bigger NVR, right-click and click Add Cam by WiFi.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-13
  4. Once the camera is paired to NVR, you’ll see it displays video on the monitor. You can then go ahead to mount the camera. NOTE: Please mount the camera within NVR’s WiFi range.
  5. If you failed to add the camera to NVR, press and hold the camera reset button for about 5 seconds to reset the camera, then pair it to NVR once again.

Install the Camera

  • Install the camera 2-3 meters (7-10 ft) above the ground. This height maximizes the detection range of the motion sensor.
  • For dome cameras, they MUST be installed upside down for better waterproof performance and better motion sensor efficiency.
  • For better motion detection performance, please install the camera angular.

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-14

Mount the Camera Mount the Camera

  1. Unscrew the bracket from the camera. Use a pencil to mark screw holes on the wall.
  2. Fix the bracket on the wall with 3 screws.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-15
  3. Attach the camera to the bracket and adjust the view angle.

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-16The PIR sensor is sensitive to heat changes, please note:

  • Avoid installing a camera that has complicated air flows. For example: the air vent of an air conditioner, the side of a fan, etc.
  • Please do not install the camera against glass or a mirror.
  • While installing, avoid lining up the camera with a path. Keeping some angle will help the camera to sense people.
  • Do not install the camera upside down. (PIR sensor is the downside.)

Mount the Solar Panel

Connect your solar-powered camera to this solar panel with a 3m connection cable (included) to get non-stop power.

  1. Please select a position with the maximum sunlight exposure throughout the year for your solar panel. Mount your solar panel facing due south (in the northern hemisphere) or due north (in the southern hemisphere) and tilt it to the appropriate angle for your latitude.
    XMARTO-Wire-Free-Security-Camera-User-Manual-fig-17
  2. Mount the bracket with the screws provided in the package.
  3. Slot the solar panel into the bracket and make sure that it’s secure.
  4. Loosen the adjusting control on the bracket and adjust the angle of the solar panel to make it receive direct sunlight exposure, then tighten the adjusting control to fix the solar panel.
  5. Connect the solar panel to the camera with the included USB cable.

XMARTO-Wire-Free-Security-Camera-User-Manual-fig-1718

NOTE:

  1. Make sure that there is NO blocking on the solar panel. The energy harvesting efficiency drops drastically even when a small portion of the solar panel is shaded by other objects.
  2. Please don’t install the solar panel completely horizontally. Other- wise, your solar panel might accumulate dust and other debris easily. It’s advised to install the solar panel angularly to make it receive direct sunlight exposure.
  3. Wipe the solar panel regularly to remove the dust and debris.
  4. Make sure that the camera is plugged in all the way and that the waterproof wire cover protects the interface between the camera and the solar panel.

Safety Instructions for Battery Usage

The camera is not designed for running 24/7 at full capacity or around-the-clock live streaming. It’s designed to record motion events and to live view remotely only when you need it.

  1. The battery is built-in, so do not remove it from the camera.
  2. Charge the rechargeable battery with a standard and high-quality DC 5V phone charger or solar panel. Do not charge the battery with solar panels from any other brands.
  3. Charge the battery when temperatures are between 0°C and 45°C and always use the battery when temperatures are between -20°C and 60°C.
  4. Keep the USB charging port dry, clean, and free of any debris.
  5. Do not charge, use, or store the battery near any ignition sources, such as fire or heaters.
  6. Do not disassemble, cut, puncture, short-circuit the battery, or dispose of the battery in water, fire, microwave ovens, and pressure vessels.
  7. Do not use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal in any way. If the battery is being used or charged, turn off the power switch remove the charger immediately, and stop using it.

Troubleshooting

TroubleSolution
 

 

1

 

Uлsuccessful лetwork coлfiguratioл

1, Make sure your phoлe, camera, aлd router are close eлough,

2, Note that the camera caллot support coллectioл to a 5G WiFi,

3, Make sure to provide correct WiFi aлd password,

 

 

2

 

 

Device oVliлe

1, Check your router’s Iлterлet coллectioл,

2, Check the coллectioл betweeл the camera aлd the router, If you chaлged the WiFi лame or password, you лeed to reset the camera aлd setup agaiл,

3, Check if the camera is out of battery, Recharge the camera wheл лeeded,

3No live viewRestart the app aлd try agaiл,
 

4

 

No push лotificatioл

1, Make sure the app has лotificatioл permissioлs, 2, Make sure the Motioл detectioл alert of camera

settiлg, aлd Push лotificatioл of App settiлg are both turлed oл,

 

 

5

 

 

No recordiлg

1, Please iлsert aл SD card to the camera before power oл; check SD card status iл camera settiлg, If it is abлormal, try to format the SD card,

2, Make sure the camera PIR switch is turлed oл,

3, Make sure the camera recordiлg switch is turлed oл,

 

Frequently Asked Questions

Does the camera work 24/7?
Yes, but we do not recommend it. Battery/solar-powered cameras are designed to work on motion-triggered bases. We strongly suggest letting the camera work in Event Recording Mode. If you need a 24/7 working camera, please purchase a plug-in power Wi-Fi camera. Here is the way to make this battery camera work 24/7: Use a 5V 1A/2A phone charger and a USB cable to keep the camera plugged into a power outlet, so the camera has constant power. Then open the WallPixel app, go to camera settings – Record Setting, and change the Record Mode to Continuous Record Mode.

Why do my cameras run out of batteries fast?
a) Make sure to fully charge your cameras before you mount them. It shall take 4-6 hours to fully charge them. b) When you are using solar panels as the power source, make sure the camera is in Event Record Mode. If you want the cameras to work in Continuous Record Mode, plug the cameras into wall outlets with 5V power chargers. c) Make sure your solar panel is properly installed to obtain solar power.

Why Need a Solar Panel?
Connecting battery camera to solar panel, you will be able to get non-stop power for your camera all day and all night. Also, you don’t need to take time to charge your cameras yourselves anymore. It will save you a lot of time.

Please contact XMARTO Support at support@xmarto.com if you have any question.

REFERENCE LINK

https://xmarto.com/

Tags: , , , , ,

Leave a Reply