XTU J1-V5.1.1 WiFi Video Doorbell Camera User Manual

XTU J1-V5.1.1 WiFi Video Doorbell Camera User Manual

What’s in the box
Please consult the below checklist for all the components.

Meet the doorbell

1. 2MP camera
2. Motion sensor
3. Speakers
4. Doorbell button
5. LED indicator
6. Charging indicator
7. Micro-USB port
8. Reset hole
9. Security screw hole
10. Microphone
11. Power contacts
12. Hardwire terminals
13. Micro-SD card slot
14. 18650 Battery pack
15. Security screw
16. Mounting screw holes

Meet the chime

1. Speakers
2. Reset
3. LED Indicator
4. USB Port (Type-A/M)

Battery installation

The batteries are pre-installed in the doorbell, with an insulation film inserted in the positive poles. Please remove the film and insert the battery pack back into the compartment, with positive poles upwards! NOTE: Improper battery installation will cause damage to the internal components and may result in serious injury.

Battery charging

The batteries inside the doorbell are not fully charged under transportation safety regulations. Please charge the batteries with a USB-compatible wall charger (not included) and the provided USB cable for about 8~10 hours before installation.

Download the app

Download and install the ‘CloudEdge’ App from Google PlayTM or the App StoreTM. The App is also available by scanning the QR codes on the right, using your QR code scanner on your smartphone. NOTE: Google PlayTM is a trademark of Google Inc. App StoreTM is a service mark of Apple Inc.

Wi-fi set up

Before you start the Wi-Fi configuration, please note below:

1. The doorbell works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi.
2. Avoid using special characters or symbols like )(@~!#$%^&*…, either in your Wi-Fi name or password.
3. Perform the configuration near your Wi-Fi router.

Launch the ‘CloudEdge’ App and register an account with your mobile phone number or email ID. Start the Wi-Fi configuration, by following the in-app instructions or referring to the following guiding steps.

Guiding steps:

Run a test
After setup, tap on the live view window in the App for a test. Then take your doorbell outside to the installation spot and run a test there. Make sure the installation spot is covered by a strong 2.4 GHz Wi-Fi signal. Note: If the video quality from the doorbell outside is not as good as it was indoors, you may need to move your router closer to your installation spot, or invest in a Wi-Fi extender.

Live viewing

1. Quit live viewing
2. Setting menu
3. Volume on/off
4. HD/SD switch
5. Full-screen display
6. Stream bit rate
7. Wi-Fi signal status
8. Battery status
9. Screenshot button
10. Speak to the visitor
11. Record on the phone
12. Motion detection on/off
13. Photo Album
14. Video Playback
15. Cloud storage service

Note:
Live viewing will not trigger video recording.

Playback
If the Micro-SD card is properly installed, you can playback the video clips taken after detected motions or visitor calls. (Live viewing will not trigger device recording). You can also back up video clips to the cloud, only if you have activated the cloud storage service (7-Day-Free Trial available).

leave Voice messages
Maximum 3 voice messages (Max. 10 seconds each) can be pre-recorded into the doorbell, which enables you to quickly respond to your visitors when you are not convenient to answer the doorbell call.

Share Your device

Sharing my account searching
Steps: Settings>>Device Share>>Tap on “Add ”>>Tap on “Account”>>Type in account ID>>Confirm Sharing.

Sharing by QR code scanning

NOTE:

1. Guide your family members to download and install the CloudEdge App, and register an account before device-sharing.
2. There is no limitation on the number of users sharing one device.
3. Only the administrator got access to the settings menu. Other users can only live view & playback.
4. All users will receive doorbell calls and alarm notifications.
5. Many users can access the doorbell simultaneously, to live view or playback.

Connect the chime

Supply power to the chime
The chime can be powered by a USB-compatible phone charger (DC5V 1A). You can also plug the chime into the USB port on your PC/notebook to supply power.

Click reset button

Click the RESET button on the wireless chime only once, and you will see the LED indicator flashing blue, indicating the chime is in pairing mode.

Press the doorbell button

Press the doorbell button, and the Chime will sound to react. Pairing succeeds, and the indicator on the chime will be in solid blue.

Chime settings
You can enter the chime setting page below the setting steps, to mute the Chime Reminder, select ringtones, adjust the chime volume, or unbind the connection with the doorbell.

NOTE:

1. Your doorbell communicates with the chime via Radio Frequency, but not WiFi. You can even do the pairing before the doorbell configuration.
2. You can add many chimes to one doorbell, and vice versa.
3. Press and hold the RESET button on the chime for 5 seconds till the indicator flashes blue 3 times, and you can also release the connection between the chime and its connected doorbell

Installation

Select location

Your doorbell has a 166-degree view angle and a 120-degree human detection range. It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance.

Hardwire your doorbell (Optional)
The doorbell works with both 12V ~ 24V AC and 12V DC hardwire power sources. Either wire can be connected to either terminal. The cable order doesn’t matter.

Go wireless installation

Note:

1. When hardwiring your doorbell, please operate under the guidance of the professionals.
2. The doorbell works with 12V – 24V AC and 12V DC power sources. And either cable can connect to either terminal. The connecting order doesn’t matter.
3. If your doorbell is powered solely on batteries, you may need to charge your doorbell once in a while. Lab-tested battery life: 12-month standby, 6 months regular use (activate 20 times per day. (The actual battery life may be different due to different activation freqency).

Specification

Video Doorbell

• Image Sensor 1/2.7” CMOS (2.0MP)
• OS Lite-OS
• Resolution 1920 × 1080 px
• Stream HD/SD dual stream
• Infrared LED High power IR LED with ICR
• Lense 1.7mm/F2.0
• The angle of view is 166°
• Min. illumin. Color: 0.01 Lux; B&W: 0.001Lux
• WDR Digital WDR
• Audio 2-way audio with noise cancellation

Storage

• Storage Type Micro SD Card (Max 128G)
• Cloud storage Support
• Recording Triggered by PIR motion sensor

Network

• Wifi Frequency 2.4 GHz ~ 2.4835 GHz
• Standards IEEE 802.11 b/g/n
• Live View Speed Within 3 ~ 4 Sec

Software

• App Name CloudEdge
• OS iOS, Android
• Remote View Within 2~4 sec
• Notification Push notification within 2~4 sec

General

• Working Temp. & Humidity -20℃ ~ 50℃; <90% (No condensation)
• Power Source Lithium 18650 Battery (3.5V, 3350mAh ) × 2/ AC 12V – 24V hardwire power/ DC 12V hardwire power
• Standby Current 300μA
• Working Current 250mA
• Standby Time 4 ~ 6 Months
• Working Time 2 ~ 3 Months (20 times wake up per day)
• Battery Charging DC5V 1A ~ 2A (Micro USB Port)
• Firmware Upgrade OTA (Over-The-Air)
• Dimension (mm) 61× 41 × 144
• Weight (g) 145 + 90 (Battery weight)

Troubleshooting

Q1: Why did I fail to set up Wi-Fi for the doorbell?
A1: ①.The device works with 2.4GHz Wi-Fi only but does not support 5GHz Wi-Fi. ②.The Wi-Fi network is not good, try to keep the camera near the Wi-Fi router when setting up. ③.The Wi-Fi password is wrong. Please check if there are special characters in the password, or if the network is specially encrypted.

Q2: How do I know if I have 2.4G or 5G wifi?
A2: Please check the user manual of your Router or call the network operator for help.

Q3: It has to be on the same WiFi to see the camera, or is it over the internet from anywhere?
A3: You can view the camera from anywhere if your camera is well connected to the internet.

Q4: Do any of the recordings get saved to the cloud? Or is it mainly saved in the built-in SD card?
A4: It supports SD card recording as well as cloud storage. You can activate the cloud storage service in the App.

Q5: What happens when the SD is full?
A5: When the memory card is full, the camera automatically erases the oldest footage.

Q6: Does it work with Google Home or Alexa?
A6: Sorry, this model does not support Google Home or Alexa.

Q7: Why does it lose wifi connection?
A7: Please check the network connection of your phone and the Wi-Fi router. If the network signal is not strong, you may need to move your router closer to the device or invest in an extender.

Q8: Can motion detection be disabled?
A8: Yes, sure. A recording is triggered by detected motions. You can set up the sensitivity or disable motion detection in the settings menu.

Q9: Do we get the charger for the batteries?
A9: Battery charger is not included. Please charge the batteries with a USB-compatible charger(DC5V 1A~2A) for about 8-10 hours.

Q10: Can we have 2 or more doorbells at the same residence?
A10: Yes, you can add more than one device at the same residence.

REFERENCE LINK

https://www.xtucam.com/