Lepow Z1 Ultra Slim Portable Monitor User Guide
Power Issue
Power LED is not ON.
- Press the button to check if the monitor is in the ON mode.
- Check if the cable is properly connected to the monitor and the power outlet.
The power LED lights amber and there is no screen image.
- Check if the monitor and the computer are in the ON mode.
- Make sure the cable is properly connected between the monitor and the computer.
- Inspect the signal cable and make sure none of the pins are bent.
Cannot connect with my device.
- This monitor does not have a battery. Make sure you firstly power it with enough current (5V/2A or above). Then connect it with your monitor.
- Make sure the power button is ON.
Connection Issue
Screen shows “Power Saving Mode”/”No Signal” and cannot be connected:
- When there’s not enough power(5V/2A) above comes in, the screen shows “power saving mode” and “no signal
- When the monitor is not connected with available device using supported port, the screen shows “no signal
- If you use an adaptor to connect, the adaptor may not compatible with this monitor. Contact Lepow to get a free new one.
- If it shows “no signal” without using any adaptor, try to change a cable to connect. You can get free replacement(support@lepow.hk) if any official accessory is damaged under warranty.
Use Type-C port to connect Cell Phones but failed.
- Use only the left type-C port(full featured) on your monitor for connection. Type-C on right side does not support data transmission.
- Make sure your cell phone has a full-featured Type-C port.
- Make sure your cell phone can provide over 5V/2A power to this monitor.Otherwise, an external power source(5V/2A or above) is needed.
Can this monitor be connected with Android phone which only has a Micro USB port?
- Yes.You need to buy an adapter, while we don’t recommend it.
- The clarity of the picture will be affected, and the experience will be worse than that of the list supported cell phones(Page 21, User Guide)
How to connect with my iPhone?
- You need an Type-C to Lightning Adaptor.
- Make sure you connect the monitor with external power source(SV/2A or above). Most iPhone only delivers 5V/1A which is not enough to power the monitor.
Use Type-C port to connect Laptops/Computers but failed.
- Use only the left type-( port(full featured) on your monitor for connection. Type-( on right side does not support data transmission.
- Make sure your device has a full-featured Type-C port.
- Make sure your device can provide over 5V/2A power to this monitor.
Adaptor Issue
Device has a Lightning/mini Display/Thunderbolt port.
In this case, if you cannot successfully connect to the monitor via Type C or HDMI port, you will need an HDMI adaptor to get it done. Please check the frequently asked cases below:
The package doesn’t include an adaptor. How can I get one?
- If your device needs an adaptor, please email support@lepow.hk. Every order has the opportunity to get a free one.
Screen Issue
My monitor flickers from time to time, and what should I do?
- This could be caused by inadequate electricity or a defective port.
- To figure it out, firstly, please connect to an external power source and see whether the monitor stops flickering. Please ensure the power supply is of 5V/2A or above without connecting with an external power source in case of flickering.
- If nothing improved after the first step, the port on the monitor should be iffy, and please contact us about this problem.
The screen turns red:
- It is in the factory testing mode. Please press the power button for 5-1 O seconds to turn off and restart it.
The screen is broken:
- It may due to the transportation problem. Contact lepow (support@lepow.hk) immediately for free replacement.
The picture shows gray on computer, but it turns white on the monitor:
- You may choose the HDR mode. Please enter the OSD menu to turn off the HDR mode.
The power indicator light (above the power button) turns in red but the monitor still shows nothing?
- If it shows “no signal’; please wait 2-1 O seconds for the reaction;
- Please confirm if you connect to the monitor via the full-function Type C port on the left side· instead of the power supply one;
- Please also try with other devices so that to figure out it is a compatibility issue or product defect.
OSD Setting
I cannot adjust the settings on the OSD menu.
Please check the following things:
- ECO setting is in Standard Mode.
- Close the HDR mode and adjust the ratio rate to “4:3”. For more issue, please refer to 05D Function lntroduction(Page 12, User Guide).
The monitor appears a blue rectangle with Chinese on it:
- Please refer to the language setting(Page 16, User Guide) to correct the language mode.
- If customer cannot enter the 05D menu, please follow the steps below:
- Step 1: Connect an external power supply like Power Bank, Wall Charger, etc. [5V/2A above]
- Step 2: Confirm connect the power cable first, and then connect the signal cord (HDMI/Type C)
- Step 3: If it still doesn’t work, please hold the power button for 5-10 seconds.
- Step 4: Press the Roll Key to enter the OSD menu.
Brightness & Volume
Brightness setting goes back to the previous, and I have to adjust frequently:
- When adjusting the brightness, please connect to an external power source to ensure the monitor has enough electric current comes in and then press the roll key to confirm. The next time you turn on the monitor, it will memorize your setting.
No volume is coming out from the monitor:
- Please ensure the volume of the connected device and the monitor is not set to O or muted.
- Please adjust the Le pow monitor as the “audio output device “on your computer, laptop, or mobile phone.
Screen Protector Installation
Is there any instruction for installing the screen protector?
For clear guidance, you can refer to the screen protector installing videos on You Tube. We also have some instructions as below:
- Firstly, please clean the screen with a wet tissue and dry with the soft cloth.
- Then, tear off the protector and be careful not to touch the surface.
- Next, aim at the edge of the screen, press the slide from the middle of the monitor with your index finger to reduce the formation of bubbles.
- If you failed to install the protector and cause many bubbles, please email us for a new one.