Adidas ZNE 01 True Wireless Earbuds User Manual
GETTING STARTED
- Open the charging case.
- Press and hold the button on the bottom of the case until the LED turns to a slow blue pulse.
- Select adidas Z.N.E. 01 from your sound device’s Bluetooth® list.
TOUCH CONTROLS
Touch the left or right earbud to control your music, phone calls and more. The long touch behaviour can be customised in the app.
- touch to play/pause or receive/end a call
- touches to skip forward or reject a call
- touches to skip backward
CHARGING THE EARBUDS
Put your earbuds back in the case and close the lid to turn them off and begin charging.
CHARGING THE CASE
Use a wireless charger or plug the case into a USB power source to charge it. The case is fully charged when the front-facing LED is steady green. To charge the case using a wireless charger, follow the instruction below.
- Place the charging case with its back flat against the wireless charging pad.
- Make sure that the front LED lights up to indicate that the case is charging.
- Once the LED light has turned steady green the case is fully charged.
LED INDICATOR
The LED shows the case battery charge, from red through yellow to green (0–100%). It pulses blue while in Bluetooth pairing mode.
PAIRING A NEW DEVICE
adidas Z.N.E. 01 remembers up to 6 previously paired devices and will try to reconnect if not connected, starting with the last connected device.
- Place the earbuds in the case and keep the lid open.
- Press and hold the button on the bottom of the case until the LED turns to a slow blue pulse.
- Select adidas Z.N.E. 01 from your sound device’s Bluetooth list.
Note: The earbuds can be connected with one sound device at a time. Make sure to disconnect from the current device before reconnecting with a different device.
ADJUSTING THE EARBUD FIT
The earbuds silicone sleeve can be removed for a looser fit. To reatach the sleeve, simply pull the silicone sleeve over the earbud.
Note: Make sure the holes in the sleeve are aligned with the sensors and ports on the earbud.
RESETTING THE EARBUDS
If your earbuds become erratic or unresponsive, follow the instructions below.
- Place the earbuds in the case and close the lid to restart the earbuds. If the problem persists, perform a factory reset.
Note: This will delete all user settings and the earbuds will need to be paired again.
- Place the earbuds in the case and keep the lid open.
- Press and hold the Bluetooth pairing button for 10 seconds, until the LED turns purple, to reset the earbuds to factory settings.
- Remove of adidas Z.N.E. 01 from your sound device’s Bluetooth list before pairing again. If the problem persists, perform a hardware reset.
Note: This will delete all user settings and the earbuds will need to be paired again.
- Place the earbuds in the case and keep the lid open.
- Press and hold the Bluetooth pairing button for 15 seconds to reset the earbuds.
- Remove adidas Z.N.E. 01 from your sound device’s Bluetooth list before pairing again.
CLEANING YOUR ADIDAS Z.N.E. 01
Earbuds come in close contact with your skin oftenb and sometimes for long periods of time. This will over time cause build-up of dirt and grease that can affect performance and may cause skin irritation. Clean your earbuds regularly to keep them fresh and make them last longer. Unplug any cables before cleaning the case. Make sure everything is completely dry before using the earbuds, putting the earbuds back in the case, or plugging in a USB charger. Use a disinfectant wipe or a lint-free cloth, slightly damp with 70% isopropyl alcohol or 75% ethyl alcohol to gently clean the exterior surfaces of the earbuds and the case. Avoid getting moisture in any openings or in the speaker mesh. Carefully clean those areas with a dry and soft brush, or a cotton swab.
- Do not use any sharp objects.
- Do not use compressed air.
- Do not use products containing bleach or hydrogen peroxide.
- Do not submerge the earbuds in any cleaning agents.
REFRENCE LINK
https://www.adidas.com/us/adidas-z.n.e.-01-true-wireless-earbuds/EY5116.html
