Twelve South 12-2021 HoverBar Duo for iPad User Manual
What’s in the Box
- A. iPad Clip
- B. Desk Base with attached arm
- C. Shelf Clamp
- D. Large Hex Wrench ( 4MM)
- E Small Hex Wrench (3MM)
- F. Shelf Clamp Collar
Getting Started Attach iPad Clip
- Position the Locking Washer at the end of the HoverBar Arm and align it with the back of the iPad Clip.
- Hand-tighten iPad Clip onto the end of the iPad Arm with a Locking Washer.
Getting Started Choose Desk Stand or Shelf Clamp
HoverBar includes both a freestanding, weighted Desk Stand and a Shelf Clamp. The Desk Stand comes pre-attached and is the easiest to move from place to place. The Shelf Clamp attaches the HoverBar Arm securely to a shelf or desk edge up to 1.5 inches thick for display in any orientation. Where and how you want to use your iPad will determine which option you choose. If you want to use the Desk Stand, simply clip in iPad (page 4) and you’re done. If you want to use the Shelf Clamp, proceed to install the Shelf Clamp.
Getting Started Clipping in iPad
- Holding the iPad horizontally, insert the bottom edge of the iPad into the clip and push down to open the iPad Clip.
- When the top of the iPad Clip is expanded beyond the top edge of the iPad, lean the iPad back into the iPad Clip.
- Carefully release the iPad and let the HoverBar iPad Clip hold the iPad.
- Rotate and position the iPad into the desired placement and orientation.
Note:
It is recommended that when adjusting the position of the iPad by a significant amount, remove the iPad first, reposition the HoverBar arms and iPad Clip to the approximate new location, then replace iPad and make final small adjustments with the iPad securely in place.
Getting Started Clipping in iPad
- Holding the iPad horizontally, insert the bottom edge of the iPad into the clip and push down to open the iPad Clip.
- When the top of the iPad Clip is expanded beyond the top edge of the iPad, lean the iPad back into the iPad Clip.
- Carefully release the iPad and let the HoverBar iPad Clip hold the iPad.
- Rotate and position the iPad into the desired placement and orientation.
Note:
It is recommended that when adjusting the position of the iPad by a significant amount, remove the iPad first, reposition the HoverBar arms and iPad Clip to the approximate new location, then replace iPad and make final small adjustments with the iPad securely in place.
Adjusting and Tightening HoverBar
All moving HoverBar joints can be adjusted and tightened as needed or desired. All hinges use one of two Hex Wrenches included with HoverBar.
- A. iPad Clip Adjustment Knob Loosen to adjust the orientation and angle of the iPad. Note: Utilize the notch opposite the adjustment knob to position the iPad parallel to HoverBar Arm.
- B. HoverBar Arm Elbow Use the Large Hex Wrench to adjust the height and angle of the Upper Arm. Base Hinge
- C. Rotation point for Lower Arm. To adjust, use Base Hinge Adjustment Screw.
- D. Base Hinge Adjustment Screw Adjust the tightness of the Base Hinge with a Small Hex Wrench.
- E. Arm Attachment Bolt Adjust the ease of rotation with Large Hex Wrench.
Getting Started Installing Shelf Clamp
Removing the HoverBar Desk Stand and installing the Shelf Clamp is a straightforward process. Pay close attention to not lose the individual washers and screws as you follow the steps to switch parts.
- Remove Arm Attachment Bolt from the bottom of the Base and release HoverBar Arm.
- Unscrew and remove the Shelf Clamp Adjustable Segment.
- Hold the HoverBar Arm upside down so the three locking posts are facing up.
- Place the Shelf Clamp Collar onto HoverBar Arm with the inner ring facing up.
- Place the Shelf Clamp onto HoverBar Arm and rotate until the Locking Plate nests into the three posts of the arm.
- Replace and tighten Arm Attachment Bolt.
- Replace the adjustable side of the Shelf Clamp and screw it into place with the Shelf Clamp Adjustment Knob.
Note:
Carefully store Desk Stand and extra Collar and Locking Plate to re-install Desk Stand at a later date.
HoverBar Tips & Tricks
Combine HoverBar with iPad to use as a second display for your Mac with Sidecar. With the SideCar feature, most newer Macs can turn most newer iPads into a second screen for applications pallets, email, small widgets, et cetera. Use HoverBar to position your Sidecar iPad right next to your Mac screen in vertical or horizontal position.
Learn more about SideCar here:
https://support.apple.com/en-us/HT210380
HoverBar and iPad – with an external keyboard & trackpad
The latest iPad lets you use external keyboards and pointing devices (such as a TrackPad or mouse) to control iPad. With iPad control on your desk – you are now free to position iPad anywhere you like with HoverBar.
Better Video chats
To look your best on FaceTime videos, Zoom calls, et cetera, it is always better to have your camera at eye level and, most often, in portrait mode. Use HoverBar to position your iPad at the perfect height for any video call. You can even hang it from a nearby shelf to keep your desktop nice and clear.