Brinno SHC1000 Peep Hole Camera Visitor Log Cam User Manual

Brinno SHC1000 Peep Hole Camera Visitor Log Cam User Manual

Package Contents

1. PeepHole Camera
2. Base Flange
3. Tightening Tool
4. Washer (SHC1000 12 only)
5. Peephole
6. 4 AA Batteries
7. User Manual
8. Quick Start Guide

Install Batteries & Micro SD Card

1. Open the battery cover.
2. Install 4 AA batteries.
3. Insert Micro SD card.

Device Parts

1. Locking screw
2. Micro SD card slot
3. Micro USB port
4. LED Indicator: LED On: Battery low. Alert to replace the batteries. LED Flashing: The camera is capturing photos.
5. Live view/ Shutter button
6. Power switch
7. Playback/ Up button
8. Settings/ Down button
9. Extension port (For optional motion sensor)
10. Battery compartment

Menu Settings

Press DOWN BUTTON to enter”MENU SETTINGS”. (Press UP or DOWN BUTTON to browse setting options.)

Browse Images
Replay visitor photos (Details in Section 11- IMAGE PLAYBACK)

Knocking Sensor
Auto capture photos when someone knocks on your door. (Details in Section 12- ENABLE KNOCKING SENSOR)

Motion Sensor
Auto capture photos when someone is near your front door. Refer manual of motion sensor(MAS200) inside the package for details.

LCD Option
When LCD option is ON, the screen auto displays images if camera detects knocking on the door or motion outside the door (must with motion sensor). Setting LCD option OFF can save power and make battery last longer.

Before You Start

Take the motion sensor unit out of the door knocker casing.

1. Remove the knocker ring.
   
2. Open the front cover.
   
3. Take out the motion sensor unit.
   

Display Icons

1. Connected sensors: The icon turns white to indicate the device is successfully connected to the sensor.
   
2. The sensor in low battery: The icon turns red to alert the battery dropping low.
   

Device Parts

Receiver Unit:

1. Connector
2. LED Indicator

Motion Sensor Unit:

1. Motion Sensor Lens
2. Battery Compartment
3. Motion Sensor Pairing Channel Switch
4. Pairing Button
5. LED Indicator

Sensor Installation

Door Knocker Mode:
Insert motion sensor unit into door knocker casing included in the package.

Portable Mode:
Hide the motion sensor unit anywhere separately near your front door.

Transmission/Detection

Transmission Distance:
32 ft (10m) between the motion sensor unit and the receiver unit inside the camera. When you choose Portable Mode, make sure the two units are within the transmission distance.

Sensor Detection Area:
Detection angle: 90 degrees (horizontal). Detection distance: 13 ft (4 m) (centerline). (approx. 5 ft (1.5 m) on both sides of the centerline).

Specifications

• ModelMAS200
• Detection Angle 90° (horizontal)
• Splash-proof IPX4 Centerline: 13 ft (4 m)
• Detection Distance Side: 5 ft (1.5 m)
• Transmission Distance to Receiver
• Power Source 32 ft (10 m)
• Battery Life  1 CR2450 battery (included)
• Operating Temperature(32 ˚F ~ 113 ˚F (0˚C ~ 45˚C)

Pairing Channels

One camera supports up to 6 motion sensors. You make different channel combinations to identify each unique motion sensor. Motion Sensor Pairing Channel Switch:

Pairing Channel Combination:

FCC

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

DOWNLOAD PDF

Brinno SHC1000 Peep Hole Camera Visitor Log Cam User Manual

 REFERENCE LINK

https://brinno.com/