UBIQUITI UVC-G3-Flex 1080P IP Camera Manual
Package Contents
Installation Requirements
- Phillips screwdriver
- Drill and 6 mm (1/4″) bit for drywall anchors and 3 mm (1/8″) for screws)
- Category 5e (or above) Ethernet cable
Note: When using the Outdoor Cover, use an Ethernet cable without a strain-relief boot on the connector. This will prevent unnecessary tension on the cable ends during installation.
Outdoor Installation Requirements
IMPORTANT: When installed outdoors, the camera must be installed in the upright postion only.
- Mount the camera in the upright position only. Please see diagram below.
- Shielded Category 5e (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial‑grade, shielded Ethernet cable from Ubiquiti Networks.
- Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH‑SP‑G2, one near the UVC‑G3‑Flex and the other at the entry point to the building. The ETH‑SP‑G2 will absorb power surges and safely discharge them into the ground.
Before You Begin
The UVC G3 Flex camera is designed to work with Ubiquiti’s new integrated management system, UniFi Protect. UniFi Protect is a flexible and powerful IP video surveillance system that can manage UniFi Protect cameras and the UniFi Protect mobile app.
For more information on UniFi Protect, visit us on the web at: unifi-protect.ui.com
Hardware Overview
Microphone Microphone for recording audio
Camera Lens Lens for viewing/recording video
Light Sensor Sensor for ambient light detection
LED Status indicator for the following:
Swivel Base Allows you to change the viewing angle of the camera by adjusting left or right. Useful if mounted on a wall or other permanent surface.
Bottom View
Ethernet Port The Ethernet Port is a 10/100 Mbps port used to supply power from a PoE 802.3af‑compliant switch to the camera. The switch should be connected to a LAN running DHCP services and the UniFi Protect Controller software.
Reset Button The Reset Button is used to reset the camera to factory defaults.
Desktop
- Remove the Base Mount from the base of the camera.
- Insert one end of the RJ-45 cable into the Ethernet Port and the other end into a PoE 802.3af-compliant switch.
- Attach the camera to the Base Mount by lining up the notches with the slots in the base of the camera.
Note: Ensure the Ethernet cable is seated in the notch between the Base Mount and base of the camera. - Place the camera on a desk or table in its upright position.
- Tilt the lens up or down to adjust the angle vertically.
- Turn the camera body left or right to adjust the angle horizontally.
Installation complete.
Specifications
Safety Notices
- Read, follow, and keep these instructions.
- Heed all warnings.
- Only use attachments/accessories specified by the manufacturer.
WARNING: Hot Surface. Do not touch.
WARNING: Do not use this product in a location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Electrical Safety Information
- Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
- There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions.
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Industry Canada
CAN ICES-3(A)/NMB-3(A)
This Class A digital apparatus complies with Canadian ICES-003.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are applicable to it.
RoHS/WEEE Compliance Statement
European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
Online Resources
- Support help.ui.com
- Community community.ui.com
- Downloads downloads.ui.com
©2018-2019 Ubiquiti Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and UniFi Protect are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple, the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android, Google, Google Play, the Google Play logo and other marks are trademarks of Google Inc. All other trademarks are the property of their respective owners.
REFERENCE
https://store.ui.com/collections/unifi-protect-cameras/products/unifi-video-g3-flex-camera
