UBIQUITI UVC-G4-PRO 4K Unifi IP Camera Manual
- Pole-mounting: Two metal straps (not included)
- Shielded Category 5 (or above) cabling with drain wire should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable.
- Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP, one near the camera and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.
- Remove the Mounting Base from the camera by turning the Tilt/Mount Ring counterclockwise.
- Mark the mounting holes on the wall or ceiling.
Note: If you are running the cable along the wall or ceiling, position the Cable Slot towards the direction you want the cabling to run. For outdoor installations, position the Cable Slot downward.
- Use a 7 mm (¼”) drill bit to drill the mounting holes in the wall or ceiling.
- Insert a Screw Anchor into each mounting hole.
- If you are feeding the Ethernet cable through the wall or ceiling, do so now and feed it through the Mounting Base.
If not, feed the Ethernet cable through the Mounting Base and place the cable in the Cable Slot.
IMPORTANT: If you are installing your camera outdoors, create a drip loop for the cable below the camera to prevent water ingress.
- Fasten the Mounting Base to the wall or ceiling using two Self-Tapping Screws.
- Remove the camera from the Adjustable Base by turning the Camera Ring in the direction shown.
- Remove the Cable Gland from the Adjustable Base.
- Feed the Ethernet cable through the Cable Gland and Adjustable Base. Seal the Cable Gland in place by firmly pressing around its edges. the cable to the Ethernet Port on the camera.
IMPORTANT: For proper weather sealing, the Cable Gland must fit securely within the Adjustable Base when the camera is mounted. Ensure that the Cable Gland is securely seated during installation and cable routing.
- Connect the camera back to the Adjustable Base by turning the Camera Ring in the direction shown.
- Orient the camera to the desired position while connecting the Adjustable Base to the Mounting Base.
- Proceed to the Connecting Power over Ethernet section.
The UniFi Protect auto-management feature should automatically detect your new camera(s). To manage the camera:
- Log in to UniFi Protect. Enter the username and password credentials used to set up the system and click Submit.
- Click Add Cameras.
Note: The green number icon on the Add Cameras button will display the number of cameras UniFi Protect has automatically detected.
- Select the camera you would like to manage. You can rename the camera by typing into the box displaying the device. Click Add Selected Cameras.
- The camera will appear on the Devices tab. The Camera Details window will be displayed on the right side of the screen. Check the camera view and proceed to the Adjusting the Camera View section.
UniFi Protect App
Download the UniFi Protect app to add this camera to your UniFi Protect system.
When you first launch UniFi Protect, the app will prompt you to enable Bluetooth and other features necessary to provide the best user experience possible. Please allow these features and permissions for proper app functionality
Connecting Power over Ethernet
The UVC G4 Pro supports 802.3af and 802.3at and can be powered by any 802.3af/802.3at compliant switch, such as an UniFi PoE Switch. Connect the Ethernet cable from the camera directly to a PoE port on the switch.
Electrical Safety Information
- Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label.
- 2. There are no operator-serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. This device complies with part 15 of the FCC Rules.
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
RoHS/WEEE Compliance Statement
European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
018-2019 Ubiquiti Inc. All rights reserved. Ubiquiti, the Ubiquiti U logo, the Ubiquiti beam logo, UniFi, and UniFi Protect are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc, registered in the U.S. and other countries. Android, Google, Google Play, the Google Play logo, and other marks are trademarks of Google, LLC. All other trademarks are the property of their respective owners.