You are currently viewing UBIQUITI UAP AC Lite Unifi Dual Radio Manual

UBIQUITI UAP AC Lite Unifi Dual Radio Manual

Views: 74
Table of contents show

UBIQUITI LOGO

UBIQUITI UAP AC Lite Unifi Dual Radio Manual

UBIQUITI UAP AC Lite Unifi Dual Radio Product image

Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi® AP. This Quick Start Guide is designed to guide you through installation and includes warranty terms.

Package Contents

UBIQUITI UAP AC Lite Unifi Dual Radio FIG 1

Hardware Overview

LED

UBIQUITI UAP AC Lite Unifi Dual Radio FIG 2

UBIQUITI UAP AC Lite Unifi Dual Radio FIG 3

Wall Mount

  1. Position the Mounting Bracket at the desired location on the wall with the arrow pointing up.
  2. Use a pencil to mark the four mounting holes. Use a 6 mm drill bit to drill the mounting holes.
    UBIQUITI UAP AC Lite Unifi Dual Radio FIG 4
  3. If your Ethernet cable feeds through the wall, then cut or drill a circle approximately 18 mm in diameter. Then feed the CAT5/6 cable through the hole.
    UBIQUITI UAP AC Lite Unifi Dual Radio FIG 5
    Note: 25 mm is the distance from the center of the bottom mounting hole to the center of the cable hole.
  4. Insert the Screw Anchors into the 6 mm holes. Secure the Mounting Bracket to the wall by inserting the Screws into the anchors.
    UBIQUITI UAP AC Lite Unifi Dual Radio FIG 6
  5. If the Ethernet cable runs along the mounting surface, remove the Cable Feed Plug.
    UBIQUITI UAP AC Lite Unifi Dual Radio FIG 7
  6. Connect the Ethernet cable to the Ethernet port.
    UBIQUITI UAP AC Lite Unifi Dual Radio FIG 8
  7. Align the arrow on the UniFi AP with the arrow on the Locking Tab of the Mounting Bracket.
    UBIQUITI UAP AC Lite Unifi Dual Radio FIG 9
  8. Ensure that the UniFi AP is firmly seated on the Mounting Bracket. Turn the UniFi AP clockwise until it locks into place and the Locking Tab fits securely into the Locking Notch.
    UBIQUITI UAP AC Lite Unifi Dual Radio FIG 10

Connecting Power over Ethernet

The single-pack of the UAP-AC-LITE includes one Gigabit PoE adapter. For multi-pack units, we recommend using a UniFi Switch with PoE.

  1. Connect the Ethernet cable from the device to the adapter’s POE port.
  2. Connect an Ethernet cable from your LAN to the adapter’s LAN port.
  3. Connect the Power Cord to the adapter’s power port. Connect the other end of the Power Cord to a power outlet.

UBIQUITI UAP AC Lite Unifi Dual Radio FIG 11

Mounting the POE Adapter (Optional)

  1. Remove the POE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes.
  2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included).
  3. Align the adapter’s slots with the tabs of the POE Mounting Bracket, and then slide the adapter down.

Specifications

UBIQUITI UAP AC Lite Unifi Dual Radio FIG 13

Electrical Safety Information

  1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not
    followed.
  2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS’ sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term.

Limited Warranty

ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions.

Safety Notices

  1. Read, follow, and keep these instructions.
  2. Heed all warnings.
  3. Only use attachments/accessories specified by the manufacturer.
    WARNING: Hot Surface. Do not touch.
    WARNING: Do not use this product in a location that can be submerged by water.
    WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Electrical Safety Information

  1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
  2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.

FCC

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Industry Canada

CAN ICES-3(A)/NMB-3(A)
This Class A digital apparatus complies with Canadian ICES-003.

CE Marking
CE marking on this product represents the product is in compliance with all directives that are applicable to it.

RoHS/WEEE Compliance Statement

European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

Online Resources

©2018-2019 Ubiquiti Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and UniFi Protect are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. Apple, the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android, Google, Google Play, the Google Play logo and other marks are trademarks of Google Inc. All other trademarks are the property of their respective owners.

REFERENCE

https://www.amazon.com/Ubiquiti-UAP-AC-LITE-802-11ac-Gigabit-Dual-Radio/dp/B01DRM6MLI

DOWNLOAD PDF

UBIQUITI UAP AC Lite Unifi Dual Radio Manual

Tags: , , , ,

Leave a Reply