Baby Brezza BRZ00139 Smart & Safe Electric Baby Bottle Warmer User Manual
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should be followed, including the following:
- Read all instructions before using.
- Do not touch hot surfaces. Use handles.
- To protect against electric shock and injury to persons do not immerse cord, plug, water tank or appliance in water or other liquid.
- Close supervision is necessary when any appliance is used by or near children.
- Unplug from outlet when not in use and before cleaning. Allow to cool before inserting or removing parts, and before cleaning the appliance.
- Do not operate this appliance with a damaged cord or plug. If the appliance malfunctions or has been damaged in any manner, contact Elfe Juvenile Products at 1-800-667-8184| or by email at: service@elfe.ca.
- The use of accessory attachments not recommended by the appliance manufacturer may cause fire, electric shock or injury.
- Use on level surface and be sure there is no debris under the unit and the rubber pads are touching the surface.
- Household use only. Do not use outdoors.
- Do not let cord hang over edge of table or counter, or touch hot surfaces.
- Extreme caution must be used when moving an appliance containing hot liquids.
- Do not place on or near hot gas or electric burner, or in a heated oven.
- Do not use appliance for other than intended use.
- This appliance has a polarized plug (one blade wider than the other). To reduce risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
- To disconnect, turn appliance off, then remove plug from wall outlet.
- Make sure machine is turned off before unplugging.
- A short power-supply cord is provided to reduce risks of becoming entangled in or tripping over a longer cord. Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If using the machine with an extension cord, make sure the cord is the proper electrical rating for the machine.
- The extension cord should be arranged so that it does not drape over a counter top or tabletop, where it can be pulled on by children or tripped over unintentionally.
- Before serving make sure food is at safe temperature for baby.
- Unplug cord from wall outlet before serving milk or food warmed in appliance.
- Do not leave cord within child’s reach.
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION:
- To maintain the compliance with the RF exposure guideline, place the unit at least 8in/20cm from nearby persons.
- If E1, E2, E3, or E4 error messages appear on the bottle warmer screen, please contact customer service before any continued use of the bottle warmer. Save these instructions
SAFE+SMART BOTTLE WARMER® PARTS
TOUCH DISPLAY CONTROLS
APP INTERFACE
Once connected, the setup screen will display on your mobile device. *
FEATURES
- Features 2 Warming Modes: Steady Warm Mode: A warm water bath gently heats milk to body temperature, preserving essential nutrients found in breast milk, which can break down at high temperatures. Quick Warm Mode: Steam is used to safely & efficiently heat formula or milk fast.
- Simple Defrost: Safely defrost frozen breast milk pouches.
- The easy-to-use control panel allows you to set up your warmer whether starting with cold or room temperature milk.
- The Baby Brezza App lets you control the warmer from your smartphone and alerts you when your bottle is ready.
- Works with all bottle types. Remember, bottles made of different materials and construction heat at different rates. Try a higher or lower setting if your bottle is too cold or too warm. Always remove venting systems when warming. Bottles with bottom venting systems may leak when heating.
USING THE SAFE+SMART BOTTLE WARMER® MOBILE APP
The bottle warmer can bet set up straight from your smart phone or tablet. Download and install the Baby Brezza Bottle Warmer App available on the app store & Google play. Bluetooth * is required on your mobile device to connect to the Safe+Smart Bottle Warmer.
CHOOSE A HEATING MODE: STEADY OR QUICK
STEADY WARM
- Fill the bottle warmer with water until it matches the level of the milk inside the bottle. Always use room temperature water for best heating results. Using warm, hot or cold water will result in inaccurate or dangerous bottle temperatures.
- Close the bottle warmer cover.
- Press to turn on machine.
- Use the setting guide on the back of this manual to determine the setting for your bottle. Make sure to select the correct bottle size and material.
- Identify the starting temperature of your bottle.
- If your bottle is room temperature (approximately 70°F/21°C) press repeatedly to select your setting.
- If your bottle is cold refrigerated 39°F/4°C) press # repeatedly to select your setting.
- Press SS to begin heating.
- Warmer will beep when bottle is ready. Remove bottle immediately after warming is complete, swirl bottle gently and check temperature before feeding baby.
QUICK WARM
- Fill the measuring cup (included on the back of the warmer) with room temperature water. Do not use warm, hot or cold water, which will result in inaccurate or dangerous bottle temperatures.
- Close the bottle warmer cover.
- Press to turn on machine.
- Use the setting guide on the back of this manual to determine the setting for your bottle. Make sure to select the correct bottle size and material.
- Identify the starting temperature of your bottle.
- If your bottle is room temperature (approximately 70°F/21°C) press repeatedly to select your setting.
- If your bottle is cold (refrigerated 39°F/4°C) press repeatedly to select your setting.
- Press 17 to begin heating.
- Warmer will beep when bottle is ready. Remove bottle immediately after warming is complete, swirl bottle gently and check temperature before feeding baby.
Please note: the quick warm mode uses steam to warm bottles. Please use caution when opening the lid after warming cycle is complete. Always use the orange bottle tray to remove the bottle from the warmer and avoid touching any hot areas of the bottle warmer. Outside of warmed bottle may be hot immediately after warming.
DEFROSTING FROZEN MILK POUCHES
To use the defrost setting, place a frozen milk pouch into the warmer and fill water to the line of the milk in the pouch. Press the * temperature setting until the “F” icon is displayed on the LCD screen, Then press to begin heating.
CLEANING THE BOTTLE WARMER
Always allow warmer to cool before cleaning
TROUBLESHOOTING
Condition
Unit will not power on.
Lid will not close.
Machine will not sync to
mobile device or is
disconnected.
Warmed bottle is too hot.
(Quick warm setting)
Warmed bottle is too hot.
(Steady warm setting)
Warmed bottle is too cold.
(Quick & Steady warm
settings)
“ES” error displays on machine
or “Error” message displays on
app.
E1, E2, E3, or E4 error displays
on machine.
Possible Cause
Possible Remedy
Unit is unplugged.
Ensure that plug is securely inserted into the power outlet.
is held for too long.
Press to turn on the unit. Do not hold down the
button.
Bottle Tray is misaligned inside bottle warmer.
Ensure that bottle tray is lined up with bottle tray
slots in the bottle warmer.
Elete th connectivity in mobile device is not
Turn on the Bluetooth connectivity in your mobile
device before syncing to the unit.
Mobile device is out of range.
Mobile device needs to be within 20ft of the bottle
warmer.
Not enough water added to bottle warmer.
Add water to the marked Quick Warm fill line.
Setting time 1s to long or incoret seting
Not enough water added to bottle warmer.
Try a lower setting according to your preference.
Add water until it matches the height of liquid in your
bottle.
Setting time is too long or incorrect setting
chosen.
Too much water added to bottle warmer.
Try a lower setting according to your preference.
Reduce water in bottle warmer to the required height
based on your setting. (Refer to page 5).
Setting time is too short or incorrect setting
Try a higher setting according to your preference.
chosen.
Little or no water has been added to the machine.
Internal malfunction in machine.
Add cold water to the machine and let it sit and cool for
5 min. Empty out cold water and restart the bottle
warmer. Make sure to add the appropriate amount of
water needed for warming.
Please contact customer service before continuing to
use your machine.
If you can not remedy problems with the machine by using the troubleshooting chart above, do not return your warmer to the store.
please contact Customer Service at: 1-800-667-8184 or by email: service@elfe.ca
CUSTOMER SERVICE
If you are experiencing problems with your Baby Brezza Safe + Smart Bottle Warmer, please call our Customer Service department at 1-800-667-8184 or by email at: service@elfe.ca before returning the product so that we can offer you our best service customized to your particular situation.
LIMITED 1-YEAR WARRANTY
The limited warranty is valid only on products bought through authorized resellers and used in Canada. Buying through an unauthorized reseller or using this product outside of Canada automatically voids this warranty. This warranty is available to consumers only. You are a consumer if you own a Baby Brezza Bottle Warmer that was purchased at retail for personal, family or household use. Except as otherwise required under applicable law, this warranty is not available to retailers or other commercial purchasers or owners. We warrant that your Baby Brezza Bottle Warmer will be free of defects in material or workmanship under normal home use for one year from the date of original purchase. Customer will be required to present original proof of purchase in order to obtain the warranty benefits. In the event that you do not have proof of purchase date, the purchase date for purposes of this warranty will be the date of manufacture. If your Baby Brezza Bottle Warmer should prove to be defective within the warranty period, we will repair it or, if we consider it necessary, replace it. To obtain warranty services, please call Customer Service at: 1-800-667-8184 or by email at: service@elfe.ca
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
REFRENCE LINK
