Cobra Dual Pro 360° Radar User Manual
Congratulations
Take the freedom of the road back with the Cobra Dual Pro 360, equipped with 360° high definition protection, threat direction arrows, and intelligent GPS technology to eliminate false alerts.
Go to Cobra.com for full featured Owner’s Manual.
Dual Pro 360 Features
- Dual Pro 360’s HD Performance accurately identifies real threats sooner than other detectors, and with threat direction arrows, provides you with location information about these threats.
- Updatable IVT Filter™ automatically reduces false alerts from moving In-Vehicle Technology sources such as collision avoidance systems and adaptive cruise control.
- GPS location-based intelligence automatically locks out false alerts and allows you to mark locations for future reference.
Access to the DEFENDER Database, which warns you of verified speed traps, speed cameras, and red light cameras. - Built in Bluetooth® technology gives you access to iRadar.
The real-time ticket-protection network which warns you of upcoming alerts received and reported by other users in the area, and gives you access to local speed limit data for over-speed alerts.
Installation
Your new detector comes with our latest EZ Mag Mount™. Simply slide the detector onto the mounting bracket fully and that’s it. To remove the detector from the mount, simply pull the detector off the mount.
Mounting Tips:
- Center of windshield between driver and passenger.
- Ensure clear view of road ahead and sky above.
- Avoid windshield wipers and heavily tinted areas.
To mount the detector in your vehicle:
- Remove backing from EZ Mag Mount.
- Firmly press EZ Mag Mount onto windshield and flip locking clamp to secure.
- Slide the detector onto the mounting bracket until it’s fully engaged. The magnet inside holds the detector in place.
- To adjust view, loosen thumb wheel and adjust angle of mounting bracket. Tighten thumb wheel to secure.
- To remove detector, simply pull the detector device off the mount bracket.
- To remove mount from windshield, release locking clamp and pull tab on top of EZ Mag Mount.
EZ Mag Mount Care Instructions:
To clean your EZ Mag Mount, simply rinse under warm water, gently wipe off any debris and allow to air dry.
Connect detector to your smartphone via Bluetooth®
- Power on Dual Pro 360.
- Install and run the Cobra iRadar app on your smartphone.
Note: the first time you run the app, you will be prompted to register a new account. - In the iRadar app. press the Settings button then select “Devices”.
- Select “Dual Pro 360 ” from the list.
- Dual Pro 360 will display “Connected” when it has paired. Press the settins button then Home to return to the Map screen.
Controls & Features
Using Dual Pro 360
- Plug small end of SmartCord into modular jack on Dual Pro 360 and large end of SmartCord into your car’s lighter/accessory socket.
- Dual Pro 360 should power on automatically. If not, press the device’s power button.
NOTE: You can easily access and customize all of your Settings and Preferences by pressing and holding the MRK and SEN buttons. See Settings and Preferences for details.
Using Smart Cord USB
Mute Button:
- Press to mute the audio for a specific alert.
- Press three times to lock out a false alert.
- Press twice while receiving a locked-out alert to unlock.
- – When connected to i Radar press and hold the mute button on unit or cord to manually report to other users a verified X or K-band alert, or a police officer observing traffic.
- Alert Light: Blinks red when receiving a laser alert.
- Power Light: Lights green when device is powered on.
- USB Charging Port: Charge smartphones, tablets and other USB chagred devices.
GPS Filter/Locking Out False Alerts
Dual Pro 360 is equipped with a True Lock GPS Filter to lock out and store in its memory false alerts. To lock out a false alert (X band, K band or laser only), press the MUTE button on the detector or the SmartCord three times durring an alert. Pressing the first time will silence the audio. Pressing a second time will generate a prompt on the display that will read “Lockout?” Press a third time to confirm you want to lock this signal out by location and frequency.
A “Stored” message will be displayed. Once a signal has been stored, Dual Pro 360 will reject the signal the next time you approach this area and will display the locked out alert. To unlock a signal that has already been stored, simply press and hold the detector or SmartCord MUTE button while receiving the locked out alert.
The display will read “Unlock?” press and hold the detector or SmartCord MUTE button again to unlock it from memory. The display will then read “Unlocked” to confirm your action. For details on how to turn the GPSfilter off, refer to the Settings and Preferences section. NOTE: When the GPS filter is set to OFF, you do not have access to Dual Pro 360’s other GPS-enabled features (e.g., Database alerts, marking locations, etc).
Speed Alert
With Dual Pro 360, you can set the Speed Alert to notify you when you are traveling over a specified speed (factory default is 70 mph; see Settings and Preference for details). When you travel above the speed threshold you have set, the background display for your current speed will turn red to alert you that you have exceeded the specified speed.
Software Updates
800.964.3138 • Cobra.com Dual Pro 360’s red light and speed camera database is easily updated using our exclusive detector software tools found on our web site. Firmware, or the operating software for the detector, can also be updated using these tools. In order to have access to these updates, you must register your Dual Pro 360 at www.Cobra.com. Once registered, you will receive email notifications that updates are now available for your database or firmware. To handle your software and DEFENDER updates you need to connect your Dual Pro 360 to a computer first. You can connect Dual Pro 360 to a computer via USB/USB Mini B cable.
Restore Factory
Settings To restore Dual Pro 360 to it’s original factory settings, press and hold MRK and BRT while turning the power on. A Restored message will display, acknowledging the reset. Notes for Programming To view serial number and software revision press MRK and MUTE while powering on detector.
