Lasko CT16550 Electronic Ceramic Heater Manual

Lasko CT16550 Electronic Ceramic Heater Manual

IMPORTANT SAFETY INSTRUCTIONS

• PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT PLUG THE HEATER INTO ANY OTHER CORD-CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET ADAPTER, CORD REEL, OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON THE SAME CIRCUIT AS THE HEATER.
• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT THE HEATER PLUG FITS TIGHTLY INTO THE OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID-STATE SPEED CONTROL DEVICES
• Make certain that the power source conforms to the electrical requirements of the Heater.
• Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended. Never leave children unattended when the heater is on or plugged in.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use a Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres.

CAUTION

• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the Heater or other objects are not resting on it. DO NOT run the Power Cord under the carpeting. DO NOT cover the Power Cord with throw rugs, runners, or similar coverings as this may cause the cord to overheat. Arrange the Power Cord away from room traffic and where it will not be tripped over.
• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use the handle when moving this Heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.
• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
• DO NOT use the Heater outdoors.
• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry, or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
• This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations.

MODEL CT16550

OPERATION Figure 1 

1. Carefully remove the Heater from the plastic bag and the carton.
2. Place the Heater on a firm and level surface. Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors.
3. Plug the cord set into a 120-volt outletP lug the cord set into a 120-volt outlet. Be sure that the plug fits tightly into the outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater.
4. When the Heater is plugged in, the Power Light will come on indicating that there is power to the unit. The Power Light will remain lit until the Heater is unplugged from the electrical outlet.
5. Turn the Heater ON by pressing the Power Button.
6. When initially turned on, the Heater will be in High heat (1500 Watts) on Max. (The High light will be steady and the Max light will be blinking).
7. Press the Power Button once and the Heater will be in Low Heat, indicated by the steady light beside Low.
8. Pressing the Power Button a third time will turn the Heater OFF.
9. When the Heater is turned OFF, the red light on the Heater will remain lit until the Heater is unplugged from the electrical outlet.

Temperature Function

The automatic temperature function will only operate on “High” heat. You cannot set the temperature automatically when the unit is in low heat mode.

1. To set the room at a specific temperature, press the Temperature Button to the desired setting. The light under the chosen temperature will continue to blink until the room reaches the desired temperature. The Heater will cycle off and on to maintain the room temperature. When set on MAX, the Heater will run continuously.

Remote Control (Figure 2):

1. . Install two “AAA” batteries (not included).
2. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
3. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY
   EXPLODE OR LEAK.
4. Press the power button on the remote to turn the heater on and off.
5. Press the “high” button to put the heater into high heat.
6. Press the “low” button to put the heater into low heat.
7. The oscillation button on the remote works identically to the oscillation button on the heater.
8. Press the plus or minus sign on the temperature control button  to select the desired temperature setting.

If you lose your remote control, please call Customer Service to order a replacement at 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m. and 5:00 p.m. EST

.

SAFETY FEATURE

1. A thermal overload protector is built in to prevent overheating.
2. If an overheating temperature is reached, the Heater will automatically shut off. It can only resume operation when the unit is reset. (See reset instructions below).
3. A Tip-Over Switch is built in to prevent operation if the Heater is tipped over.

To Reset Heater:

1. Unplug the Heater and wait 10 minutes for the unit to cool down.
2. After 10 minutes, plug the Heater in again and follow the OPERATION INSTRUCTION described in this instruction manual.

TROUBLESHOOTING TIPS
If your heater shuts off unexpectedly or fails to operate, the previously mentioned safety feature may have been activated to prevent overheating.

1. Be sure the power cord is plugged into a working electrical outlet.
2. Check your Temperature setting. The Heater may be off because it has reached the desired temperature setting.
3. If your Heater runs for several minutes and shuts off repeatedly, your Heater may require cleaning.

See the Maintenance section below. If you have a problem that can not be resolved by the steps listed above, contact Technical Assistance at 1-800-233-0268, Monday through Friday, between the hours of 8 am and 5 pm EST.

MAINTENANCE

Warning
To reduce the risk of electrical shock and fire please observe the following instructions. Cleaning the Heater regularly will help to maintain its efficiency.

• Always unplug the cord before moving, servicing, or cleaning.
• NEVER place the Heater in or near water. DO NOT IMMERSE THE HEATER IN WATER.
• Clean the Heater only with a vacuum equipped with a brush attachment; the vacuum will remove the lint and dirt from the surface of the Heater.
• Vacuum intake grills every two weeks; this will help to maintain the optimum Heater performance.
• Use a toothbrush or other soft bristle brush to gently loosen any dirt not removed by the vacuum.
• NEVER attempt to take apart the Heater.
• Clean the body of the Heater with a soft cloth only.
• NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.

SERVICING:
For servicing, other than general user maintenance, please contact Customer Service at 800-233-0268, Monday through Friday, from 8 am-5 pm Eastern.

STORAGE:
Store the Heater with these instructions in the original carton in a cool, dry place. DISPOSITION: Corrugated packaging materials are recyclable. For environmentally responsible disposal of this product, contact your local waste service provider or visit www.1800recycling.com®.

LASKO PRODUCTS, LLC LIMITED WARRANTY

WHAT THIS WARRANTY COVERS:
This product is warranted against defects in workmanship and/or materials. HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for three (3) years from the date of original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.

WHAT LASKO WILL DO:
Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model. For all warranty claims, the product must be returned to Lasko Products, LLC at customer expense with proof of purchase within the warranty period. Contact the Lasko customer service department to obtain a Return Authorization (“RA”). DO NOT return products without an RA or the warranty claim will not be processed.

WHAT THIS WARRANTY DOES NOT COVER:
This warranty does not apply if the product was damaged or failed because of the accident, improper handling or operation, shipping damage, abuse, misuse, unauthorized repairs made or attempted, or the use of the product for commercial or nonresidential service. This warranty does not cover shipping costs for the return of products to Lasko for repair or replacement. Lasko will pay return shipping charges from Lasko following warranty repairs or replacement.

CUSTOMER SERVICE:
Toll-Free (800) 233-0268. Email: producthelp@laskoproducts.com Our Customer Service team is available to assist you with product and service questions, and replacement parts. They can be reached Monday through Friday, 8 am-5 pm Eastern. Please have your model number available, as well as the type and style (located on the underside of your product). Customer Service Dept., 820 Lincoln Ave., West Chester, PA 19380 (Please do not send the product to this location) www.laskoproducts.com

REFERENCE LINK

DOWNLOAD LINK

Lasko CT16550 Electronic Ceramic Heater Manual