Dr. Infrared Heater DR-238 Carbon Infrared Outdoor Heater User Guide

Dr. Infrared Heater DR-238 Carbon Infrared Outdoor Heater User Guide

IMPORTANT SAFETY INSTRUCTIONS

1. Read all instruction before using this heater.
2.  Remove the unit from its packaging and check to make sure it is in good condition before using.
3.  Do not let children play with parts of package (such as plastic bags).
4.  Check the household voltage to ensure it matches the heater’s rated specification.
5.  Check the power cord and plug carefully before used, to make sure that they are not damaged.
6. Before unplugging the power cord, be sure to turn off the power, when energizing the unit, be sure your hands are dry to prevent from electric shock.
7.  Do not use flammable objects near or point the heater like furniture, pillows. bedding, paper, clothes and curtains at least 3 feet (1 meter) from the front of the heater and keep them always the sides and rear.
8.  Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
9.  To protect against electric shock, do not immerse cord or plug in water or any other liquid.
10.  Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the heater.

Accessories Parts

1. L shaped bracket 4pcs
2.  Plastic anchor 4pcs
3. Screw M5*25mm 4pcs
4.  Nut M6 2pcs
5.  Screw M6*12mm 2pcs

Installation

Mounting step

1.  L shaped Bracket installation Fasten the L shaped braket using the screws and nuts provided (no.4 and no.5)
2. Mark holes on the place where the heater to be mounted with a pencil.
3.  Drill holes with a smaller diameter drill bit than the plastic anchors
4. Insert the point end of plastic anchor into the holes, Tap the anchor with a hammer until the anchor is flush
5. Using a screwdriver attach the mounting bracket to the holes which with plastic anchor inside.
6. Fasten the heater on the L shaped bracket by the black screws on the back of heater.

• • The supplied mains cable must not contact the top surface of the heater during operation. The mounting height and intensity should reflect the intended use of the heater.

FUNCTION & OPERATION

OPERATING
Product Key Function:

1. Turn on the power, the product is standby mode display (- -);
2. Press key function: press the button, then press the heat levels (L1-L2-L3- standby – off)

Remote Control Instructions:

1. POWER BUTTON: Turn the heater off.
2. UP BUTTON: Increase timer and level.
3. DOWN BUTTON: Decrease timer and level.
4. LEVEL BUTTON: Use to adjust the heat levels(L1-L3). Press the Level button then use the up and down buttons (buttons 2 and 3) to increase or decrease the heating level.
5. TIMER BUTTON: To set the timer from 0H-9H, which is the number of hours it will run. 0Hwill
   display and then adjust to the number of hours you would like to set, using the up and down buttons (2 and 3).

PUSH BUTTON: on the right of heater, it could be manual operated without remote control.

Inserting Batteries (no included)
Insert 2 AAA/ Alkaline type batteries into your remote control

1.  Flip the backside of your remote control and pull out battery cover. Insert the batteries in accordance with the instructions and polarity the batteries.
2. Change the batteries in the same way depicted above

MAINTENANCE

Attention! Careful and regular maintenance of your heater considering our instructions assume great importance so as to attain a long efficient operation of your appliance.

1. Check the filthiness of the Reflector and IR-Filament at least once a month. If necessary, apply cleaning and maintenance instructions.
2. The number of checks may be increased considering the amount of the dust in the environment.
3. Check the deformation of the Reflector, Wire and Frame visually while cleaning the appliance. In case of deformation, consult to your technical service.
4. Check the Power Cord and Plug visually while cleaning the appliance. In case of deformation, consult to your technical service.

CLEANING

Regular and careful cleaning helps your infrared heater operate efficiently for many trouble-free years. To clean your heater, follow steps below:

1. Unplug the power cord for your safety before cleaning your appliance.
2. Make sure the heater is cool before continuing.
3. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth.
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
5. DO NOT immerse the heater in water
6. Wait until the heater is completely dry before use. Storage: Store the heater in a cool, dry location when not in use to prevent dust and dirt buildup. Use packaging carton to store.

ATTENTION:

1.  Always disconnect the heater from the electricity supply and allow it to cool before attempting to work on it.
2. If the heater has collected dust or dirt inside the unit or around the heating element, have to unit cleaned by a qualified service agent. Do not operate the heater in this condition.
3. The only maintenance required is cleaning of the external surfaces of the heater.

Troubleshooting

1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the main fuse is working
3. Check to see if the power button on the back of heater is power on.
4. Error code shows on display

• E1 Error on Display: Control unit overheat. Check installation clearances. Let heater cool for 15 minutes and restart heater.
• L1,2,3,show sin display, but no heat: Bulb is damaged. Arrange for replacement bulb with local
  Dealer.

REFERENCE LINK

https://drheaterusa.com/