Faber VEGA Electric Silver Fireplace Silver User Manual
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2, and EN60555-3 which cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC.
OVERVIEW
Important Safety Advice:
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: If the appliance is damaged, check with the supplier before installation and operation. Do not use outdoors. Do not use it in the immediate surroundings of a bath, shower, or swimming pool. Do not locate the appliance immediately below a fixed socket outlet or connection box.
This appliance is not intended for use by children or other persons without assistance or supervision if their physical, sensory, or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance. In the event of a fault unplug the appliance. Unplug the appliance when not required for long periods. The appliance must be positioned so that the plug is accessible. If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person to avoid a hazard.
General
Unpack the appliance carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier. Before connecting the appliance check that the supply voltage is the same as that stated on the appliance. Please note: Used in an environment where background noise is very low, it may be possible to hear a sound that is related to the operation of the flame effect. This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED This appliance must be used on an AC ~ supply only and the voltage marked on the appliance must correspond to the supply voltage. Before switching on, please read the safety warnings and operating instructions
Transportation fixings – see Fig. 8
The transport bracket must be removed from the fire prior to installation, remove the 2 screws and the bracket. Warning: This bracket must be removed before installation; failure to do this will result in having to uninstall the product to replace a defective bulb.
Installation – see Fig.1
Ensure when building your fire into the surround that the front glass can be removed at all times. (Refer to ‘Lamp Replacement section’) As when this is removed it allows the customer to change the bulbs and in the unlikely event that a service engineer needs to access the interior components of the fire. The fire is fixed from the rear. The 4 fixing brackets need to be fixed to the rear of the fire, using the screws provided. There are slots in these brackets to allow for adjustment of the fire in position. Please use 4 suitable wood screws to firmly fix the fire to the surround.
Controls – see Fig. 2
Manual & Remote Operation. The Standby switch must first be turned ‘ON’ to operate the fire manually or by remote control. To turn the flames on, press the I button. To turn the flames off, press the O button. To increase or decrease the brightness of the flames, use the dimmer button or the buttons on the Remote Control. To turn off the power the Standby Switch must be turned ‘OFF’.
Controls – see Fig. 2
Manual & Remote Operation. The Standby switch must first be turned ‘ON’ to operate the fire manually or by remote control. To turn the flames on, press the I button. To turn the flames off, press the O button. To increase or decrease the brightness of the flames, use the dimmer button or the buttons on the Remote Control. To turn off the power the Standby Switch must be turned ‘OFF’.
Warning:
It takes time for the receiver to respond to the transmitter. Do not press the buttons more than once within two seconds for correct operation.
Battery information – see Fig. 7
- Slide open the battery cover on the back of the remote control
- Install AAA batteries into the remote control
- Replace the battery cover. Discard leaky batteries. Properly dispose of batteries according to provincial and local regulations. Any battery may leak electrolyte if mixed with a different battery type if inserted incorrectly if all the batteries are not replaced at the same time, if disposed of in a fire, or if an attempt is made to charge a battery not intended to be recharged.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Lamp Replacement – see Fig. 3, Fig. 4 and Fig. 5
To gain access to the lamps first slide the outer glass up using the suction cups and then lift the glass out from the bottom and slide it out (Fig. 3). Warning: The fuel effect is fragile, and should be handled with due care. Remove the fuel effect from the fire by removing the fixing screws from the fuel bed and the 9-way connector and the fuel bed will slide out of the fire. (Fig. 4). Remove the rotisserie by carefully sliding the rubber connector off the motor shaft. (Fig. 5) Remove the defective lamp by unscrewing it as shown in (Fig 5). Replace it with a 60W E14 SES Clear Candle lamp. Take care not to over-tighten the lamp. Refit the rotisserie, fuel bed, and outer glass.
Recycling
For electrical products sold within the European Community. At the end of the electrical products useful life, it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.
After Sales Service
Should you require after-sales service or should you need to purchase any spares, please contact the retailer from whom the appliance was purchased or contact the service number relevant to your country on the warranty card. Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory service. Please retain your receipt as proof of purchase.
REFERENCE LINK
https://vega.am/en/faber-2.html
