Flux Ador Infrared Laser Printer User Manual
What’s in the box?
Accessories
- Laser module
- Vent hose
- Clamp
- Power adapter
- Power cord
- USB cable
- Prism Lift x6
Tool
- Hex wrench
Consumables
- Lubricating oil
- Wood piece
Product & Warning labels
Safety Precautions
- Do not let minors operate alone.
- Confirm that the person who intends to operate the machine has read the safety precautions carefully and followed the instructions in the manual.
- Make sure to install the vent hose properly. An exhaust hose missing or not
installed properly will increase the risk of laser, fumes, and dust hazards. - Do not modify the machine without FLUX authorization.
- Do not try to modify, defeat or disassemble safety interlocks.
- Do not place the machine in a humid, splashing rain or direct sunlight space. In case of rain or extreme weather, please stop using the machine and put the vent hose inside.
- Do not place liquid, flammable, or explosive objects near the machine.
- Do not place any living beings in the machine. It is strictly prohibited.
- There are no noise hazard concerns as the Ador’s working level is below 70 dB.
Machine Handling
The Ador weighs 19 kilograms. It is recommended to have two people lift it cooperatively to avoid injury
Fire Hazard
- Do not leave the machine unattended while in use.
- Regularly clean the debris inside the Ador.
- In case of fire, turn off the power immediately and unplug the power cord.
- Always have an accessible, functioning fire extinguisher in the workplace.
- Confirm that the engraving material does not pose any higher risk when burned at high temperatures.
Laser Safety
FLUX Ador is a Class 1 Laser Product and a Consumer Laser Product, complying with the IEC 60825-1:2014 and EN 50689:2021 certifications. The IEC 60825-1:2014 standard categorizes laser systems into eight safety classes: 1, 1C, 1M, 2, 2M, 3R, 3B, and 4. FLUX Ador is the Class 1 Laser Product, the safest among all classes, and aligns with the laser safety standards set by the International Electrotechnical Commission (IEC). EN 50689:2021 is a laser safety standard designed explicitly for consumer laser products. It guarantees that lasers with this certification meet the highest safety standards for consumer use. These assurances are provided through the laser’s enclosed protective housing and interlocks safety devices. For further information, please refer to the safety precautions on the ”Ador Help Center”.
Work Position of Operator
Assembly
Take out the Accessories Box and remove two fastened hand screws Ⓐ on both sides of the X-rails and cushioning materials Ⓑ in the machine. You can keep and place the two removed hand screws at the Ⓒ location.
- Install the Laser Module. Loosen the hand screw Ⓐ on the module adapter Ⓑ.
- Aim the dot Ⓒ on the laser module to the unlock icon Ⓓ on the module adapter and insert it down to the lock icon.
- Press the module with your hand and ensure it’s tightly attached to the module adapter then fastening the hand screw Ⓐ back.
- Install the vent hose.
- Loosen the clamp on the exhaust fan cover using a Phillips screwdriver and remove the cover.
- Remove the cushioning material in the vent hose.
- Insert the clamp on the large end of the vent hose hole, and attach it to the exhaust fan outlet at the rear of the machine.
- Adjust the clamp tightness and fasten it onto the exhaust fan outlet.
- Direct the open end of the vent hose outside the window or connect it to an air purifier.
- Connect the power cord Ⓐ and the power adapter Ⓑ. Connect both ends of the power adapter to the power port Ⓒ at the rear side of the machine and insert the plug into the socket. Switch on the main switch Ⓓ located at the rear of the machine to turn on the machine.
For more information please refer to the “Start” chapter on the “Ador Help Center.”
Setup for the First Use
- Follow the guide on the machine display to select your language.
- Read the Safety Precautions carefully.
- Follow the instruction and run the Start-up Test. Do not skip the Start-up Test if this is the first time using the machine.
- Following the step-by-step instructions, the Start-up Test will guide you through installing the laser module and checking the door interlocks, autofocus, motors, limit switches, and module connection.
- Follow the guide on the machine display to set the Wi-Fi connection (2.4 GHz), or connect with an ethernet cable to your router and select connect later.
- Download the latest stable version of Beam Studio on your computer. https://flux3dp.com/downloadsSelect the language on Beam Studio and follow the Connection Setup.
- Check the ”Ador Help Center” if you encountered any issues running the Start-up Test. Beam Studio for mobile devices: http://studio.flux3dp.com
- Follow the software tutorial. You can initiate it by accessing the tutorial in the ”Help” menu if you accidentally skip it.
Warranty
The latest version of the warranty will be uploaded at the following URL: https://support.flux3dp.com/hc/en-us/categories/202672617 As a FLUX consumer, you benefit under certain conditions from additional warranties. FLUX offers specific consumer warranty benefits which are in addition to, and not instead of, any legal warranties provided by your national consumer law. The duration and conditions related to the legal warranties are provided by respective local laws.
REFRENCE LINK
