GARMIN Bark Limiter Deluxe Series Owner Manual

GARMIN Bark Limiter Deluxe Series Owner Manual

Introduction

 WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other important information.

Device Overviews

Bark Limiter Device

1. Contact points
2. Mode and intensity dial
3. Status LED

Bark Limiter Deluxe Device

1. Contact points
2. Mode and intensity dial
3. Status LED
4. Charging clip contacts (Bark Limiter Deluxe model only)

Attaching the Dog Collar Device to the Collar Strap

1. With the buckle © facing outward, insert the end of the collar strap through the slot 2 on the collar device.
2. Pull approximately two-thirds of the collar strap through the slot.
3. Insert the end of the collar strap through the slot 3 on the opposite side of the device.
4. Pull the strap until it is tight across the front of the device.

Charging the BarkLimiter Deluxe Device

NOTICE
To prevent corrosion, thoroughly dry the contacts on the collar and the surrounding area before connecting the charging clip

Before you put the collar on the dog, remove the charging clip. If you do not remove the clip, it may become detached from the collar and become lost.

You should fully charge the battery before you use the device for the first time. Charging a fully depleted battery takes about two hours. The device will not charge when outside the temperature range of 32° to 104°F (0° to 40°C).

1. Snap the charging clip © onto the device.
2. Plug the small end of the power cable into the mini-USB port” on the charging clip.
3. Plug the other end of the power cable into a power source.
   The status LED is solid red when the collar is charging.
4. After the status LED turns solid green, remove the charging clip from the collar.

Turning On the Dog Collar Device

Rotate the dial away from N.
There is a 30-second delay before the device becomes active.
The status LED indicates the battery charge level for five seconds and turns off. After an additional 25 seconds, the unit is active. The status LED flashes occasionally to indicate that the unit is detecting sound, motion, or vibration.

Turning Off the Dog Collar Device
Rotate the dial to N.

Rotating the Dial

NOTICE
Do not over-rotate the dial. The dial does not rotate past 7.
The dial is intentionally difficult to rotate. This helps to preventVaccidental rotation while the device is in use on the dog. Insert a coin or similar obiect into the slot to rotate the dial.

Bark Correction

When the device is active and properly fitted on the dog, it detects and corrects barks automatically. You can adjust the method and intensity of the corrections.
The status LED flashes briefly when the device detects motion or corrects a bark.

• Short flash Motion was detected, and no correction was applied.
• Long flash A bark was detected, and a correction was applied.

Fitting the Collar on Your Dog

CAUTION
To prevent irritation from the contact points, remove the collar for at least eight hours out of every 24-hour period.
This device is not intended for human use. Do not attempt to use on any person.

NOTICE
Before you put the collar on the dog, remove the charging clip. If you do not remove the clip, it may become detached from the collar and become lost.

In order to properly detect and correct barks, the collar and device must fit the dog properly. If the collar is too loose or positioned incorrectly, bark corrections may be inconsistent.

This can delay or prevent the dog from learning not to bark.

1. Place the collar around the middle of the dog’s neck.
2. Position the device at the front of the dog’s neck, with the status LED facing towards the dog’s chin and the contact points against the throat.
   TIP: The device contact points should be positioned near the dog’s vocal cords. This location varies based on the breed of dog. If the device does not seem to detect the dog’s barks, you should move the device closer to or further from the dog’s body to find the ideal location.
3. Tighten the strap so that it is very snug around the dog’s neck, and fasten the buckle.
   NOTE: The collar should fit tightly and should not be able to rotate or slide on the dog’s neck. The dog must be able to swallow food and water normally. You should observe your dog’s behavior to verify that the collar is not too tight.
4. Wiggle the device to work the contact points through the dog’s coat.
   NOTE: The contact points must have contact with the dog’s skin to effectively detect and correct barks.
5. If the strap is too long, cut off the excess, leaving at least 3 in. (8 cm) to spare.
   TIP: You can mark the hole used to fasten the buckle for future reference.

Changing the Bark Correction Mode and Intensity Level

Rotate the dial to select an option:

• To correct using vibration, select V.
• To correct using automatic intensity, select A.
• To correct using a set intensity level, select 1 to 7.

A higher number indicates a higher intensity level.

Vibration
The device can use a short vibration to correct the dog. When using vibration, no electrical stimulation is used.

Automatic Intensity
The device can set the stimulation intensity level automatically based on the barking behavior of the dog. The device starts at the lowest intensity level and increases the intensity level gradually until the dog stops barking. When the dog is quiet, the intensity decreases over time.

The automatic intensity feature is designed to eliminate excessive nuisance barking. To stop barks more immediately, you should set the intensity level manually.

Choosing the Correct Intensity Level

CAUTION
To prevent irritation from the contact points, remove the collar for at least eight hours out of every 24-hour period.
You can set the stimulation intensity level manually from 1 to 7.

You should choose the lowest intensity level that discourages the dog from barking. If you have never used a bark correction collar with the dog, the dog requires time and experience to learn that the bark is the cause of the stimulation.

1. Set the intensity to the lowest level.
2. For thirty minutes, when the dog barks, observe the dog for a reaction, such as a head shake, neck movement, a change in the way the dog barks, or just a change in expression.
3. If there is no reaction, increase the intensity by one level until the dog has a slight but recognizable reaction to the stimulation.
4. Allow 24 hours for the dog to learn to respond by not barking.
5. If the dog continues barking while wearing the collar, increase the intensity level gradually until you find the level that discourages the dog from barking.

Bark Odometer™

When you turn off the device, the LED flashes red and green to report the number of times the device detected a bark since it was last turned on. This can help you track your dog’s barking behavior.

• Red flash: 10 barks
• Green flash: 1 bark

For example, one red flash followed by four green flashes indicates the device detected 14 barks.

Checking the Bark Odometer

1. Remove the device from the dog.
2. Position the device so that you can see the status LED.
3. Rotate the dial to N.
4. Count the red and green flashes.

Troubleshooting

My device does not seem to be active
When the device is active, the status LED flashes only when the device detects a bark or motion.

• Verify the collar is turned on (page 1).
• Verify the battery is not low (page 3).
• Remove the device from the dog, and shake the device briefly.

When the device is active, the device detects the motion, and the status LED flashes.

My dog is still barking

If the dog continues barking while wearing the device, you can try any of these options to improve the effectiveness of the device.
Tighten the collar until it is very snug.

• Adjust the position of the device on the dog’s neck.
  Wiggle the device to work the contact points through the dog’s coat.
• Gradually increase the intensity level.

Device Information

BarkLimiter Specifications

Bark Limiter Deluxe Specifications

Sleep Mode
To conserve battery life, the device goes into sleep mode when no barks or motion are detected. The
activity level of your dog affects the battery life of the device.

Checking the Battery Charge Level
Rotate the dial away from N.
The color of the status LED indicates the battery charge level for five seconds.

Bark Limiter Battery Replacement Instructions

WARNING: Do not use a sharp object to remove batteries.
CAUTION: Contact your local waste disposal department to properly recycle the batteries.

Bark Limiter Components

Replacing the Bark Limiter Battery

Before you replace the battery, you must remove all dirt, water, and debris from the device. You also need a small Phillips screwdriver.

You must replace the battery with a 3V CR2 lithium battery.

• Remove the four screws from the corners of the back
• Remove the back

The battery comes out with the back plate.

• Remove the
• Install the new battery into the back plate according to the polarity indicators engraved on the back

When properly installed, the battery snaps into the back plate.

• Verify that the gasket is not damaged and that it is completely seated in the groove.
• Replace the back
• Replace the four screws to secure the back

Bark Limiter Deluxe Battery Replacement Instructions

WARNING
This product contains a lithium-ion battery. To prevent the possibility of personal injury or product damage caused by battery exposure to extreme heat, store the device out of direct sunlight.

Do not use a sharp object to remove batteries.

CAUTION: Contact your local waste disposal department to properly recycle the batteries.

Bark Limiter Deluxe Components

Replacing the Bark Limiter Deluxe Battery Assembly
Before you replace the battery, you must remove all dirt, water, and debris from the device. You also need the security screwdriver included with the new battery assembly.

You can purchase a replacement battery assembly at http://buy.garmin.com or from your Garmin dealer. The battery assembly includes a pre-assembled back plate with a gasket, battery, and battery connector.

• Remove the four security screws from the corners of the
• Lift up the battery
• Disconnect the battery connector from the

TIP: You should grip the wires close to the connector and pull the connector outward from the circuit board.

• With the new battery assembly, connect the battery connector to the device.

When properly installed, the connector plug snaps into the port and the top face of the connector plug is flush with the edges of the port.

• Verify that the gasket is not damaged and that it is completely seated in the groove.
• Hold the battery assembly and the device firmly together, and replace all four security screws without
• Verify that the battery assembly and the device are aligned with no gaps.
• Tighten the screws evenly.

Getting More Information

You can find more information about this product on the Garmin® website.

• Goto garmin.com/outdoor.
• Goto garmin.com/learningcenter.
• Go to http://buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement

Registering Your Device

Help us better support you by completing our online registration today.

• Goto http://my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe

DOWNLOAD LINK

https://static.garmin.com/pumac/barklimiter_OM_EN.pdf

https://www.garmin.com/en-US/p/133653