HOLMAN CO1606 Drip Irrigation System User Manual
Overview
Package Contents
- Indoor Timer/Pump with 500mm Water Inlet Cable and Filter
- Clear Protective Cover
- USB to USB-C Charging Cable
- 9× 4mm Barbed Drippers
- 1× 4mm Barbed End Plug
- 10m × 4mm Hose
- 10× 4mm Hold-Down Stakes
- Hanger Connector
- Wire Hanger
Additional Functions
- Supply water via a 4mm barbed inlet or standard water bottle cap thread
- By default your Indoor timer is set to ‘nonwatering’ mode.
- To reset your Indoor Timer, hold down
and
for 5 seconds. - Home use: Recharge when battery levels reach 30%
- Holiday use: Keep Indoor Timer on charge
- Approx. 28-day battery life off charge based on: 4×1 minute waterings per day for 28 days
- Inactivity on your Indoor Timer controls for 20 seconds will return to the default system mode displaying the current time.
for 5 seconds.Specifications
| Interval scheduling | 1, 3, 6 or 12 hours, or 1-7 days |
| Watering duration | 5-60 seconds, or 1-60 minutes |
| Dripper flow rate | 0-0.7 L/min |
| Inlet | 4mm barbed or standard water bottle |
| Outlet | 4mm barbed |
| Charge time | 4 hours MAX |
Setup
Charging the Unit
Charge the Indoor Timer before use with the included USB-C Charging Cable. Connect to a USB adaptor or portable charger with a 5v DC output. Vacation warning: battery charge can last for up to 28 days
- Remove the Clear Protective Housing from the Indoor Timer
- Plug the USB-C Charging Cable into the slot located on the side of the Indoor Timer [a]
- The orange LED [b] on the back will be constantly ON during charging. The LED will turn OFF when fully charged.
- Check the display to monitor battery levels [c]. Recharge when the battery levels are indicated as low (30%)
Set Clock
This process is to set the SYSTEM CLOCK for your Indoor Timer ® Your Indoor Timer system time is always in 24-hour format (military time)
- Pressto edit the system clock [a]
- The hour and clock symbol will begin flashing
- Press+or-to adjust the hour [b]
- Pressto selects the minutes. The current minutes will begin flashing
- Press+or-to adjust the minutes [c]
- Pressto confirm the current minutes. The display will return to the home screen [d] with your set SYSTEM CLOCK.
Start Time
This process is to set the START TIME for your watering to begin
- Pressand the timer symbol and START TIME hour [a] will begin flashing.
- Press+or-to adjust the START TIME hour [b]
- Pressto select the minutes. The current START TIME minutes will begin flashing.
- Press+or-to adjust the minutes [c]
- Pressto confirm the START TIME and the WATERING DURATION will begin flashing [d]
START TIME will stop flashing to confirm the time has been set.
Watering Duration
This process is to set the WATERING SCHEDULE for the Indoor Timer. Your Indoor Timer can water every 1, 3, 6, or 12 hours or every 1 to 7 days. If your Indoor Timer has reverted to the home screen, press until
- Press+or-to adjust the hours or days [b]
- Pressto confirm the WATERING SCHEDULE and the display will return to the main menu [c] showing your current schedule.
This process is to set the WATERING SCHEDULE for the Indoor Timer. Your Indoor Timer can water every 1, 3, 6, or 12 hours or every 1 to 7 days. If your Indoor Timer has reverted to the home screen, press until the cycle symbol and WATERING SCHEDULE begin flashing [a]
- Press+or-to adjust the hours or days [b]
- Pressto confirm the WATERING SCHEDULE and the display will return to the main menu [c] showing your current schedule.
Position and Water Source
Place your Indoor Timer in a position that is easily accessible and within reach of your water source. Indoor Timer must be placed at ground level or below all plants
- The Indoor Timer has a 500mm water inlet cable with filter [a], place this in your still water source.
- Utilize the included wire hanger and hanger connector to easily mount or position your Indoor Timer.
- When using a water bottle, remove the attached water inlet cable and fill the source up completely
- Screw the Indoor Timer onto the water bottle until it is secure [b]. Flip over the Indoor Timer so it is face down.
Installation
Setting up Drippers
When setting up drippers, ensure that drippers are no higher than 1.5m above your Indoor Timer.
- Connect one end of the 4mm hose [a] to the barbed outlet [b] on the side of your Indoor Timer
If the hose is difficult to attach, hold the end in boiled water to soften the plastic. - Unravel enough length of hose to reach the middle of your first plant pot
- Cut the hose and insert a barbed dripper [c] into the length of the hose coming from the Indoor Timer.
Ensure that the barbed dripper is inserted all the way into the 4mm hose - Attach the hose to the other end of the barbed dripper [d] and continue to unravel until you reach your next plant
- Place a hold-down stake [e] next to your barbed dripper to hold it in place.
- Again, cut the hose at the desired length and insert your next barbed dripper [f]
- Once all of your barbed drippers are installed, close off your system by inserting the end plug [g] into the last piece of hose [h] 8. Secure the end plug-in position by using a hold-down stake [i]
The end plug will water the last plant that it is placed into ® Tighten or loosen drippers to adjust the flow ® Manually run your system to ensure drippers are working correctly, adjust flow if needed.
Maintenance
Cold Weather
Do not use with freezing cold water. Keep your Indoor Timer out of freezing conditions as this can damage internal components.
Charging
- Home use: Recharge when battery levels reach 30%
- Holiday use: Keep Indoor Timer on charge if away for more than 28 days
- Approx. 28 day battery life off charge based on: 4×1 minute waterings per day for 28 days
We really appreciate having you as a customer, and would like to say thank you for choosing us. We recommend registering your new product on our website. This will ensure we have a copy of your purchase and activate an extended warranty. Keep up to date to with relevant product information and special offers available through our newsletter. www.holmanindustries.com.au/product-registration/
