Honeywell RCHC4400WF1004 Camera Manual
Installation
Download the Honeywell Home app.
Note:
Have your Wi-Fi password available before installation.
- Make sure Bluetooth is enabled on your mobile device.
- Search for Honeywell Home in the App Store or Google Play.
- Download the Honeywell Home app.
Launch the Honeywell Home app
- Launch the Honeywell Home app.
- Create an account (if necessary), or sign in to your Honeywell Home account. Tap ADD DEVICE or the plus sign.
- Select the C2 Wi-Fi Camera to install, then follow the instructions in the Honeywell Home app to name the camera and its location.
Connect the power cord
- Plug the power cord’s micro USB end into the camera.
- Plug the power cord’s USB end into the wall outlet adapter, and plug your camera into a power outlet.
- Wait until the LED on the camera blinks blue (about 1 minute), then tap NEXT.
Connect
Connect to mobile device
- Enable Bluetooth on your mobile device.
- The app will look for the camera.
- For One camera, it will connect automatically.
- For more than one camera, the app will prompt you to select one camera at a time. Each camera has a unique MAC ID printed on the back. Use that ID to select the camera you want to connect.
- A QR code will display in the app. To connect your camera to the app, hold the QR code approximately 3-6 inches (7-15 cm) from the camera lens.
- The camera LED turns purple and the camera beeps.
Connect to Wi-Fi
Be sure you are on the same Wi-Fi network you wish to connect your camera to.
- Choose your Wi-Fi network from the list. Tap NEXT.
- Enter your Wi-Fi password, if necessary. Tap DONE. Note: The camera will beep during some steps in this process.
Wi-Fi Connection LEDs
During a Wi-Fi connection, the LED indicates the following.
| LED | Camera state |
| Blinking Green | Connecting to Wi-Fi network. |
| Solid Green | Connected to Wi-Fi network. |
| Solid Red (for 2 seconds) | Connection failed. LED will then turn solid purple. |
| Solid Purple | QR Code scan complete. Go to “Connect to Wi-Fi” on page 3. |
| Blinking Blue | The camera has lost Bluetooth connection. Unplug the camera and plug it back in. See “Connect the power cord” on page 2 for instructions. |
Operation
Honeywell Home app experience
When you launch the application, your Home screen is displayed. All of your devices (cameras, thermostats, water leak detectors, etc.) are displayed. Select a camera from the list to view live video from that camera.
Testing smoke/CO alarm detection
If your smoke or carbon monoxide alarm goes off and your camera is on, it will send you an alert that a smoke or CO alarm has been detected. To test this feature, press and hold the Test button on your smoke/CO detector for at least 5 seconds or 3 cycles of the detector’s alarm. A shorter test might not trigger a sound event. For a list of compatible alarms see Resideo.com.
Camera Overview
Reset
If your Wi-Fi connection fails or you need to connect to a different Wi-Fi network, insert one end of a paperclip into the reset hole. Press and hold it for 10 seconds until you hear a chirp.
SD card
The camera comes with an encrypted 16GB SD card installed. It stores images if the camera’s connection to the cloud is lost. You can replace it with any compatible SD card.
Status LED
The camera has an LED that gives the device status.
| LED | Camera state |
| During installation | |
| Blinking Blue | Powered up. Ready to begin setup. |
| Solid Blue | Connected to app. Ready to complete setup. |
| Solid Purple | QR Code scan complete. Go to Connect to Wi-Fi process. |
| Blinking Green | Connecting to Wi-Fi network. |
| Solid Green | Connected to Wifi network. |
| Solid Red | Setup timed out. Unplug camera, plug it back in, and restart the process. |
| During operation | |
| Blinking Green | Connecting to Wi-Fi network. |
| Solid Green | Connected to Wi-Fi and operating. |
| Blinking Red | Not connected to Wi-Fi. |
FCC Regulations
§ 15.19 (a)(3)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
§ 15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
IC Regulations
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. Contains lithium-ion batteries. Please dispose of it properly and in accordance with local law.
INPUT: 100 V–240 V ~50 Hz–60 Hz, 0.9 A The operation of this equipment is subject to the following two conditions: (1) this equipment or device may not cause harmful interference, and (2) this equipment or device must accept any interference, including interference that may cause undesired operation.
Need help?
- Web: resideo.com
- Phone: 1-800-633-3991
The operation of this equipment is subject to the following two conditions: (1) this equipment or device may not cause harmful interference, and (2) this equipment or device must accept any interference, including interference that may cause undesired operation. The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.
REFERENCE LINK
https://www.manua.ls/honeywell/rth8500d/manual
