Kenmore KW3030 Wet Dry Canister Shop Vacuum User Guide

Kenmore KW3030 Wet Dry Canister Shop Vacuum User Guide

BEFORE USING YOUR NEW VACUUM CLEANER

Read this Use & Care Guide. It will help you assemble and operate your new Kenmore vacuum cleaner most safely and effectively. For more information about vacuum cleaner care and operation, call the Vacuum Cleaner Help Line at 1-844-608-3080 (US) / 1-844-608-3081 (CA). You will need the complete model and serial numbers when requesting information. Your vacuum cleaner’s model and serial numbers are located on the Model and Serial Number Plate. Use the space below to record the model number and serial number of your new Kenmore vacuum cleaner.

PACKING LIST
Your KENMORE INTUITION ® BAGGED UPRIGHT VACUUM CLEANER is packaged with the following parts and components assembled separately in the carton:

• 1 Vacuum Assembly
• 1 Hose
• 1 Base
• 1 Wall Mount Rack
• 1 Round Dusting Brush
• 1 Crevice Tool
• 1 Multi-Surface Floor Nozzle
• 1 Utility Tool
• 1 Reusable Cloth Filter (Pre-installed)
• 1 Foam Wet Filter
• 1 Dust Bag
• 3 Extension Wands
• 2 Casters
• 2 Wheels
• 1 Handle
• 4 Small Screws (Bag)
• 2 Screws (Bag)
• 1 Use & Care Guide

IMPORTANT SAFETY INSTRUCTIONS

Read all the instructions in this guide before assembling or using your vacuum cleaner. Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons, or damage when using your vacuum cleaner, follow basic safety precautions including the following:

• Use your vacuum cleaner only as described in this Use & Care Guide. Use only with the manufacturer’s recommended attachments.
• Disconnect the electrical supply before servicing or cleaning out the brush roll area. Failure to do so could result in the brush roll unexpectedly starting, causing personal injury from moving parts.
• Do not leave the vacuum cleaner when plugged in. Unplug from the outlet when not in use and before performing maintenance.
• To reduce the risk of electrical shock – Do not use it outdoors or on wet surfaces.
• Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
• Do not use a damaged cord or plug. If a vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, immediately discontinue use and call 1-844-608-3080 (US) / 1-844-608-3081 (CA) for assistance.
• Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not handle the plug or vacuum cleaner with wet hands.
• Do not put any objects into openings.
• Do not use any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
• Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not put on chairs, tables, etc. Keep on the floor.
• Do not use a vacuum cleaner to pick up flammable or combustible liquids (gasoline, cleaning fluid, perfumes, etc.), or use in areas where they may be present. The fumes from these substances can create a fire hazard or explosion.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

SAVE THESE INSTRUCTIONS
Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your vacuum cleaner is intended for Household use. Read this Use & Care Guide carefully for important use and safety information. This guide contains safety statements under warning and caution symbols.

VACUUM CLEANER WARRANTY

LIMITED WARRANTY
FOR ONE YEAR from the date of sale this product is warranted against defects in material or workmanship. WITH PROOF OF SALE a defective product will be replaced free of charge. The Kenmore brand is used under license. Direct all claims for warranty service to 1-844-608-3080 (US) / 1-844-608-3081 (CA). This warranty does not cover filters or belts, which are expendable parts that can wear out from normal use within the warranty period. This warranty is void if this product is ever used for other than private household purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Cleva North America, Inc., Greenville SC 29607

EXTENSION CORDS

When using an extension cord with your Wet/Dry Vacuum refer to the following table to determine the required A.W.G. wire size. Before using the cleaner make sure the power cord and extension cord are in good working condition. Make repairs or replacements before using the vacuum cleaner. Only use extension cords that are rated for outdoor use

PARTS AND FEATURES

It is important to know your vacuum cleaner’s parts and features to ensure its proper and safe use. Review these before using your vacuum cleaner.

REPLACEMENT PARTS

To order a replacement part, call 1-877-531-7321 (US) / 1-844-608-3081 (CA).

NOTE:
The hose and accessories for this vacuum are 1-1/4” (32mm) diameter.

Please pay special attention to these hazard alert boxes, and follow any instructions given. WARNING statements alert you to such hazards as fire, electric shock, burns, and personal injury. CAUTION statements alert you to such hazards as personal injury and/or property damage.

ASSEMBLY INSTRUCTIONS

Before assembling the vacuum cleaner, check the PACKING LIST (page 3). Use this list to verify that you have received all the components of your new Kenmore Vacuum Cleaner.

WARNING
Electrical Shock Hazard. DO NOT plug into the electrical supply until assembly is complete. Failure to do so could result in electrical shock or injury. To reduce the risk of electric shock, do not be exposed to rain.

1. Undo the latches.
   
2. Lift the powerhead of the collection tank.
   
3. Remove the contents from inside the collection tank.
   
4. Insert the casters and wheels into the respective sockets on the bottom of the base. Apply pressure until casters and wheels snap into place.
   
5. Turn the collection tank upside down and fit the base assembly onto the tank. Secure the base to the tank with the supplied four small screws. Verify that the base is assembled correctly. Do not over-tighten screws.
   
6. Hold the handle in one hand and align it with openings on top of the motor housing. Push down firmly onto the top of the handle until snaps into position.
   
7. Your vacuum comes ready for dry vacuum cleaning. If the reusable cloth filter is not installed, refer to page 18 for installation instructions.
8. For wet vacuum cleaning, remove the reusable cloth filter, and install the supplied foam wet filter. See page 19 for the foam wet filter installation instructions.
9. Place the powerhead back on the collection tank align the top section with the latches, and snap it into place.
   
10. Insert the large end of the hose into the vacuum port on the collection tank.
    
11. Choose the desired accessory and insert it onto the end of the hose or extension wand.
    
    For your convenience, this vacuum comes with a wall mounting support for storage.
    IMPORTANT!
    • Do not mount the rack over 5 feet from the floor.
    • Do not screw the wall mount rack to drywall only. Secure the screws to a stud.
    • Do not hang from or sit on the vacuum when on a wall mount rack.
    • Do not use the vacuum while it is mounted on the wall mount rack.
    • Empty the collection tank before mounting the vacuum on the wall.
12. Make sure the rack is level and mark the hole locations. Align the two screw holes so that they are over a stud and secure the mount rack to the wall stud with the two screws provided.
    
13. Place the wet and dry vacuum cleaners into the wall-mount rack.
    

OPERATING INSTRUCTIONS

WARNING
Be sure to read, understand, and apply information entitled ‘important safety instructions’. Do not vacuum in areas with flammable gases, vapors, or explosive dust in the air. Flammable gases or vapors include but are not limited to lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol, or aerosol sprays. Explosive dust include but are not limited to coal, magnesium, grain, or gunpowder. To reduce the risk of health hazards from vapors or dust, do not vacuum toxic materials.

CAUTION
Do not vacuum drywall dust or fireplace soot or ash with a standard wet/dry filter. This is a very fine dust that will not be captured by the filter and may cause damage to the motor

NOTE:
To reduce the risk of electric shock, this vacuum cleaner has a polarized plug; one blade is wider than the other. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

DRY VACUUMING OPERATION 

1. Verify that the power cord is disconnected from the outlet.
   
2. To prepare your vacuum for dry vacuuming, make sure the reusable cloth filter completely covers the filter cage against the powerhead. Your wet/ dry vacuum comes with the reusable cloth filter pre-installed.
   
3. Optional: For improved dust filtering, fit the dust bag flange onto the inlet port, taking care not to damage the bag. Dust bag sold separately
   
4. Place the powerhead back on the collection tank and secure it in place using the latches.
   
5. Insert the larger end of the hose into the vacuum port.
6. Choose the desired accessory and insert it onto the end of the hose or extension wand.
   
7. Verify that the switch is in the ‘O’ OFF’ position before plugging the power cord into the outlet. Plug the power cord into the outlet.
   
8. Turn the motor on by flipping the switch to the ‘I’ ON position and begin vacuuming.
   
9. Once you have completed vacuuming, flip the on/off switch to the ‘O’ OFF position and unplug the power cord from the outlet
   • O = OFF I = ON

LIQUID VACUUMING OPERATION

WARNING
Be sure to read, understand, and apply information entitled ‘important safety instructions’. Do not vacuum in areas with flammable gases, vapors, or explosive dust in the air. Flammable gases or vapors include but are not limited to lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol, or aerosol sprays. Explosive dust includes but is not limited to coal, magnesium, grain, or gunpowder. To reduce the risk of health hazards from vapors or dust, do not vacuum toxic materials.

1. Verify that the power cord is disconnected from the outlet. Make sure that the collection tank is clean and free of dust and dirt.
   
2. Remove the reusable cloth filter, then carefully install the foam-wet filter over the filter cage and place the powerhead back on the collection tank.
   
3. Choose the desired accessory and insert it onto the end of the hose or extension wand.
   
4. Verify that the on/off switch is in the ‘O’ OFF position before plugging the power cord into the power outlet. Plug the power cord into the outlet.
   
5. Turn the motor on by flipping the switch to the ‘I’ ON position.
   
6. Once you have completed vacuuming, flip the switch to the ‘O’ OFF position and unplug the power cord from the outlet.
7. After use, empty the collection tank, and clean and dry the inside and outside of the collection tank.

IMPORTANT!
When vacuuming large quantities of liquids, do not immerse the nozzle completely in the liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve that stops the suction action when the collection tank reaches its maximum capacity. You will notice an increase in motor speed.

When this happens, turn off the machine, disconnect from the electrical supply, and drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit the powerhead to the collection tank. After wet vacuuming, turn the machine off and remove plug from the electrical supply. Empty the collection tank, and clean, and dry the inside and outside before storage.

VACUUM MAINTENANCE AND CARE

WARNING
Always disconnect the plug from the outlet before removing the powerhead from the collection tank.

EMPTYING THE COLLECTION TANK

1. Verify that the power cord is disconnected from the outlet.
   
2. Disconnect the hose from the vacuum.
   
3. Undo the latches and remove the powerhead from the collection tank. Place the powerhead on a soft, clean surface upside down.
   
4. Clear all dirt or debris from the collection tank and hose into a proper waste container.
   
5. Clean or replace the filters.
6. Check the hose, accessories, and power cord to verify that they have not been damaged.
7. Place the powerhead back on the collection tank and secure the latches.

NOTE:
The filters included are made of high-quality materials designed to stop small dust particles. The reusable cloth filter should be used for dry pickup only. A dry reusable cloth filter is necessary to pick up dust. If the reusable cloth filter is wet, it will clog quickly and be very difficult to clean. Handle the filter carefully when removing it for cleaning and replacing it. Check the filters for tears or small holes. A small hole can let dust pass through and out of the filter. Do not use a filter with holes or tears; replace it immediately.

STORAGE
Before storing your vacuum, the collection tank should be emptied and cleaned. The accessories should be cleaned and stored so they can be readily available when needed. Store the wet/dry vacuum indoors.

REPAIRS
Repairs for this wet/dry vacuum should be performed only by qualified service personnel using only identical replacement parts.

INSTALLING & CLEANING FOAM WET FILTER

INSTALLING FOAM WET FILTER

1. Verify that the power cord is disconnected from the outlet.
   
2. Remove the powerhead and place in an upside-down position.
3. Carefully slide the foam wet filter down over the filter cage making sure the cage is completely covered.
   
4. Place the powerhead onto the collection tank.

CLEANING FOAM WET FILTER 

1. With the removed powerhead in an upside-down position, carefully remove the foam-wet filter.
   
2. Use a mild soap and water solution to wash the foam-wet filter and rinse with clean water.
   
3. Allow the wet filter to air dry for 24 hours before installing it onto the filter cage.

TROUBLESHOOTING

Review this table to find do-it-yourself solutions for minor performance problems. Any service needed, other than maintenance described in this Use & Care Guide, should be performed by a qualified service agent

WARNING
Always turn off and unplug the vacuum cleaner before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shock or personal injury.

REFERENCE LINK

https://www.kenmore.com/