Kenmore KW4070 Pet Portable Carpet Cleaner User Manual

Kenmore KW4070 Pet Portable Carpet Cleaner User Manual

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions in this guide before assembling or using your carpet cleaner.

WARNING!
Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons or damage when using your carpet cleaner, follow basic safety precautions including the following:

• Use your carpet cleaner only as described in this Use & Care Guide.
• Use only manufacturer’s recommended attachments.
• Fully assemble before operating.
• Operate cleaner only at voltage specified on rating plate.
• Connect to a properly grounded outlet only. See GROUNDING INSTRUCTIONS.
• Do not modify the 3-prong grounded plug.
• Do not leave carpet cleaner when plugged in. Unplug from outlet when not in use and before performing maintenance.
• Do not expose to rain. Store indoors.
• Do not immerse. Use only on carpet moistened by cleaning process.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not use with a damaged cord or plug. If carpet cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped in water, immediately discontinue use and call 1-877-531-7321 (US) / 1-844-608-3081 (CA) for assistance.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run carpet cleaner over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or carpet cleaner with wet hands.
• Do not put any objects into openings.
• Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Keep carpet cleaner on a level surface.
• Do not carry the carpet cleaner while in use.
• Use extra care when cleaning stairs. To avoid personal injury or damage, and to prevent the carpet cleaner from falling, always place carpet cleaner at bottom of stairs or on floor. Do not place carpet cleaner on stairs or furniture, as it may result in injury or damage.
• Do not put carpet cleaner on chairs, tables, etc. Keep unit on the floor.
• Do not use carpet cleaner to pick up flammable or combustible liquids (gasoline, cleaning fluid, perfumes, etc.), or use in areas where they may be present. The fumes from these substances can create a fire hazard or explosion.
• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.
• Do not use or store near hazardous materials.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use carpet cleaner without tanks in place. To reduce the risk of electric shock, always install float before any wet pick-up operation.
• Do not clean over floor electrical outlets.
• Do not use the carpet cleaner to pick up sharp hard objects, small toys, pins, paper clips, etc. They may damage the carpet cleaner or tanks.
• Do not use sharp objects to clean out hose as they can cause damage.
• To help prevent matting and resoiling, avoid contact with carpets until they are dry. Keep children and pets away from carpets until they are completely dry.
• Do not store the carpet cleaner with solution in tanks.
• You are responsible for making sure that your carpet cleaner is not used by anyone unable to operate it properly

CAUTION

To reduce the risk of injury from moving parts – Unplug before servicing.

WARNING

• To reduce the risk of electric shock – Unplug before cleaning or servicing.
• To reduce the risk of electric shock – Use indoors only.

SAVE THESE INSTRUCTIONS

Proper assembly and safe use of your carpet cleaner are your responsibilities. Your carpet cleaner is intended for Household Use. Read this Use & Care Guide carefully for important use and safety information. This guide contains safety statements under warning and caution symbols.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This appliance is for use on a nominal 120- V circuit and has a grounding attachment plug that looks like the plug shown in the illustration. Make sure that the appliance is connected to an outlet having the same configuration as the plug. No adapter should be used with this appliance.

WARNING

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

CARPET CLEANER WARRANTY

LIMITED WARRANTY 

FOR ONE YEAR from the date of sale this product is warranted against defects in material or workmanship. WITH PROOF OF SALE a defective product will be replaced free of charge. The Kenmore brand is used under license. Direct all claims for warranty service to: 1-877-531-7321 (US) / 1-844-608-3081 (CA). This warranty is void if this product is ever used for other than private household purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Cleva North America, Inc., Greenville SC 29607

PARTS AND FEATURES

It is important to know your carpet cleaner’s parts and features to assure its proper and safe use. Review these before using your carpet cleaner.

REPLACEMENT PARTS

Item Part No.(US) Part No.(CA)
3.5” Tough Stain Tool 591033101 591033101
6.5” Wide Path Tool 591033102 591033102
Flexible Hose 671004101 671004101
Handle 671004102 671004102
Wand 671004103 671004103

To order a replacement part, call 1-877-531-7321 (US) / 1-844-608-3081 (CA).

Please pay special attention to these hazard alert boxes, and follow any instructions given. WARNING statements alert you to such hazards as fire, electric shock, burns and personal injury. CAUTION statements alert you to such hazards as personal injury and/or property damage.

ASSEMBLY INSTRUCTIONS

Before assembling the carpet cleaner, check the PACKING LIST (page 2). Use this list to verify that you have received all the components of your new Kenmore Carpet Cleaner.

• Insert the handle into the wand until you hear a ‘click’.

• Insert the wand into the main body until you hear a ‘click’.

• Make sure the upper cord hook is in the proper position as shown. Wrap the power cord loosely around the upper and lower cord hooks.

NOTE: Make sure to wrap the power cord around the upper cord hook first, and then around the lower cord hook to avoid damaging the power cord.

• Lock power cord plug onto the power cord.

WARNING Electrical Shock and Personal Injury Hazard

Wrapping the cord too tightly with excessive stress on the cord may cause  cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

OPERATING INSTRUCTIONS

FILLING THE CLEAN WATER TANK

• Press the clean water tank release button with your thumb, and then lift up the clean water tank from the main body using the carrying handle.

• Open the clean water tank cap. Fill the tank with room temperature tap water and solution. Ensure the correct proportion of water and carpet cleaning solution is used by referring to the solution label. Do not exceed filling the clean water tank over the maximum fill line indicated on the clean water tank.
• Room Temperature Water Cleaning Formula Small area – bottom fill line (0.2 gal liquid) 3 caps Large area – top fill line (0.6 gal liquid) 9 caps

CAUTION
Do not fill with water above 104°F (40°C). Do not heat water or tank in microwave.

FILLING THE CLEAN WATER TANK

NOTE:

• An 8 oz. (236ml) bottle of cleaning formula is provided with this carpet cleaner. Ensure the cleaning formula and water are mixed correctly. Water must be at room temperature. Once depleted, the cleaning formula can be replaced by a high-quality liquid carpet cleaning solution that can be purchased from a local retailer.
• Using more than the recommended amount of cleaning formula may cause excessive foaming. KEEP OUT OF REACH OF CHILDREN. In case of eye contact, thoroughly flush with cold water. If irritation persists, consult a physician.

• Snap the clean water tank cap back into place.

• Align the clean water tank with the wand and slide the tank back into place, pressing down firmly until it feels secure.

USING THE CARPET CLEANER

NOTE:

• Before using the carpet cleaner, use a vacuum to remove loose dirt from area to be cleaned. Test a small hidden area for colorfastness.
• Gently rub surface with a dampened white cloth. Wait 10 minutes and check for color removal with a white paper towel. If color changes, do not use.
• To prevent staining, use plastic or aluminum foil to protect wood or metal surfaces from possible water spray.

• To protect the wood floors underneath rugs or carpet, place waterproof material (e.g. plastic) underneath them before cleaning.

CAUTION
Moving parts! To reduce the risk of personal injury, DO NOT touch the brushrolls when the carpet cleaner is on. Contacting brushrolls while they are rotating can cut, bruise or cause other injuries. Disconnect electrical supply before servicing or cleaning the carpet cleaner. Use caution when operating near children or pets.

• Turn the upper cord hook to either side and down to release the power cord.

• Detach the power cord plug from the power cord.
• Be sure the power cord is locked into the upper locking notch as shown. This will help manage the power cord when operating the carpet cleaner.

• Plug the power cord into a properly grounded outlet located near the floor.

WARNING Personal Injury and Product Damage Hazard

• When any abnormality/failure occurs, stop using the product immediately and disconnect the power plug.
• DO NOT use outlets above counters. Damage from cord to items in surrounding area could occur.

• Turn on the carpet cleaner by pushing the power button with your foot.

NOTE: The brushrolls do not rotate when the carpet cleaner is in the upright locked position.

• Release the handle by placing a foot on the recline button and pulling back to change handle position.

• Tilt the wand back towards you and with the nozzle flush with the floor surface. Press the spray trigger to apply solution while making 2 slow wet passes: 1 forward and 1 back.

• Release the spray trigger. Make 2 slow dry passes: 1 forward and 1 back, to suck up the dirty solution.

NOTE: DO NOT hold down the trigger for this step

CAUTION
Do not allow the carpet cleaner to remain in one spot for any length of time when the brushrolls are turning. Damage to carpet may occur.

NOTE: Do not over-saturate carpet. Be careful not to run over loose objects or edges of area rugs. Stalling the brushrolls may result in premature belt failure.

• Empty the dirty water tank when the dirty liquid reaches the “Max Fill” line and there is a loss in suction. See instructions in the EMPTYING DIRTY WATER TANK (page 16).
• Once you have completed cleaning, push the power button again to turn the carpet cleaner off; unplug the powercord from the power  outlet.

USING THE CARPET CLEANER WITH HOSE & TOOL

• Place the carpet cleaner in the upright locked position.
• Open the flexible hose door. The door flips toward the nozzle cover to open.

• Insert the flexible hose as shown. Make sure the two hose release clips are locked into place. The cleaning solution delivery tube is suggested to face upwards.

• Connect the end of the cleaning solution delivery tube to the cleaning solution outlet on the nozzle and turn clockwise to secure as shown.

• Select the preferred tool and slide it onto the hose end until you hear a ‘click’. To remove: Press the tool release button and pull out the tool. 3.5” Tough Stain Tool: Use for carpet stains, furniture and other hard-to-reach surfaces. 6.5” Wide Path Tool: Use for cleaning stairs and larger furniture areas.

MAINTENANCE AND CARE

Always follow all safety precautions when performing maintenance to the carpet cleaner.

WARNING Electrical Shock and Personal Injury Hazard

Disconnect electrical supply before servicing or cleaning the carpet cleaner. Failure to do so could result in electrical shock or personal injury from carpet cleaner suddenly starting.

CARPET CLEANER INTERIOR CLEANING

• Turn off and unplug carpet cleaner. Fill the clean water tank with warm tap water and then empty it all to rinse. Then fill again with warm tap water. Reinstall the clean water tank to the unit.
• To flush and rinse the carpet cleaner, turn on the unit and press the spray trigger for 15 seconds while making back and forth passes on a section of carpet.
• Release the spray trigger and vacuum up the water.
• Empty the dirty water tank.

CLEANING EXTERIOR AND ATTACHMENTS

• Turn off and unplug carpet cleaner. DO NOT drip water on carpet cleaner.
• To clean exterior, or to reduce static electricity and dust build-up, wipe outer surface with a clean, soft cloth that has been dipped in a solution of mild liquid detergent and water, then wrung dry. Wipe dry after cleaning.

NOTE: Wash attachments in warm soapy water, rinse and air dry. Do not
clean in dishwasher.

CARPET CLEANER STORAGE

WARNING Electrical Shock and Personal Injury Hazard

Wrapping the cord too tightly puts stress on the cord and can cause cord damage. A damaged cord is an electrical shock hazard and could cause personal injury or damage.

• Clean the attachments thoroughly before storing. Place attachments in the accessory bag.
• Gather the cord and wrap it loosely around the cord hooks. Lock plug retainer onto the power cord.
• Empty the clean water tank. Rinse it out before placing back on the unit. Open the clean water tank cap to allow it to air dry.
• Empty the dirty water tank then rinse, clean and dry before placing back on the unit. The wide tank opening is designed to fit your hand inside to thoroughly clean, rinse and dry.
• Store the carpet cleaner in a dry, indoor area at room temperature.

CLEANING TOOLS

It is recommended to clean tools with water after each use.

NOTE: When the tools are worn or broken, replace the tools. To purchase tools, call 1-877-531-7321 (US) / 1-844- 608-3081 (CA).

• Press the tool release button to remove the tool from the hose.

• Press the cover release button on the tool and pull off tool cover. Remove the insert by pulling it off with force, if necessary

• Rinse thoroughly with clean water. Allow the parts to dry before reinstalling.
• DO NOT wash in the dishwasher.
• DO NOT install while damp.
• Reinstall the tool cover and the insert back into place until a click is heard.

TROUBLESHOOTING

Review this table to find do-it-yourself solutions for minor performance problems. Any service needed, other than maintenance described in this Use & Care Guide, should be performed by a qualified service agent.

WARNING

Disconnect electrical supply before performing maintenance to the carpet cleaner. Failure to do so could result in electrical shock or personal injury

PROBLEM

• The cleaner will not run.
• Poor job of dirt pick- up.
• Water escapes from the cleaner.
• Reduced or no spray through nozzle of the cleaner.

POSSIBLE CAUSE

• Unplugged at wall outlet.
• Defective wall outlet.
• The motor is damaged.
• Dirty water tank is not installed correctly.
• Dirty water tank is full.
• Flexible hose door may not be closed tightly in place.
• Brushrolls may be wrapped with hair or debris.
• Nozzle cover is not fully snapped into place.
• The flexible hose is clogged.
• Dirty water tank is full.
• Dirty water tank is not installed correctly.
• Clean water tank is not installed correctly.
• Clean water tank is empty.
• Clean water tank is not installed correctly.

SOLUTION

• Plug in firmly.
• Check with a good appliance or lamp. Be sure the power cord plug is fully plugged into a good wall outlet.
• Call 1-877-531-7321 (US) / 1-844-608-3081 (CA) for assistance.
• Check the dirty water tank for correctinstallation. Ensure it is installed in place.
• Empty the dirty water tank.
• Check the flexible hose door and make sure it is closed tightly.
• Remove obstruction. Follow instructions on page 20.
• Reinstall the nozzle cover. Follow instructions on page 20.
• Clean the hose. Follow instructions on page15.
• Empty the dirty water tank.
• Check the dirty water tank for correct installation. Ensure it is installed in place.
• Check the clean water tank for correct installation. Ensure it is installed in place.
• Fill the clean water tank.
• Check the clean water tank for correct installation. Ensure it is installed in place.

REFRENCE LINK

https://kenmorefloorcare.com/products/kenmore-revitalite-carpet-cleaner.html