Laresar Evol 3 Robot Vacuum Cleaner User Manual

Laresar Evol 3 Robot Vacuum Cleaner User Manual

SAFETY INSTRUCTIONS

Use Restrictions

• This machine is only used for floor cleaning at home. Please do not use it outdoors (such as an open balcony), in non ground areas (such as a sofa), and in commercial or industrial environments.
•  Do not use the machine in suspended environments without protective fences, such as duplex floors, open balconies, and the top of the furniture.
• Do not use the product in an environment where the temperature is above 40°C or below 0°C, or there are liquids and viscous objects on the ground.
• Hang up the ground cable at home before use to avoid dragging the cable when the machine is running.
• Put away the fragile objects and sundries (such as vases and plastic bags) on the ground.

Battery and Charging

•  Do not use any third-party batteries, docking stations, or chargers.
• Do not disassemble, repair, or modify the battery or docking station without permission.
•  Do not place the docking station near heat sources, such as radiators.
•  Do not use a damp cloth or wet hands to wipe or clean the docking station shrapnel.
• Dispose of used batteries properly, and send them to professional recycling agencies.
•  If the power cord is damaged or broken, stop using it immediately and buy a new one through official channels.

Packing List

Basic Parameters

Product Introduction

Remote Control

Sensor and its Structure 

1. Top Cover
2.  Button
3. Bumper
4. Infrared Anti-Collision Sensor
5. Infrared Light Receiving Sensor

1. Cliff Sensor
2. Charging Contact
3. Universal Wheel
4. Side Brush
5. Battery Cover
6. Drive Wheel
7. Rolling Brush
8. Installation Hole for Mopping Cloth Holder

 Electric Control Water Tank and Rag Components

1.  Water Inlet
2. Water Tank Button
3. Mopping Cloth Holder
4.  Mopping Cloth

Charging Station

1. Power Indicator
2.  Signal Transmitting Area
3.  Power Interface
4. Charging Pins

Preparation

Precautions

1. Remove the protection material from both sides of the robot
2. Install side brushes: Put the left brush (L) and right brush (R) against the letters L and R on the bottom respectively; move down for “click” to finish installation.
3. Take out and place the dust collection charging base on a flat floor against the wall and tidy up the redundant wires.
4. Ensure space more than 0.5 m from the left and right to the charging base and 1.5m in front of the charging base.
5. Do not move the charging base at will, avoid direct sunlight on the charing base.
6. Power on and charging: Hold the button to power on the machine. When the indicator is on, put the robot against the charging dock for charging. The voice of “start charging” prompts successful charging.

Use Instructions

• Power on and off the machineTap and hold the button for 3 seconds to power on the machine.Then, the power indicator is on, and the vacuum cleaner enters the standby state. Tap and hold the button for 3 seconds to power off the machine.

Cleaning/Pause
Once the machine powers on, tap the button on the robot or use the controller or the smart APP to start cleaning.

•  The machine cannot clean liquid.
•  If the power is lower than 15%, the machine cannot work. Therefore, charge the machine before cleaning.
• If the power is lower than 15% during cleaning, the machine will automatically return back to the dock for charging.
• Before cleaning, tidy up all kinds of wires on the ground (including the power cord of the dock). Otherwise, the machine may drag the wires while cleaning, which may cause power failures of other electric appliance or damage items or wires.

Charging

• Auto mode: After cleaning, the robot automatically returns to the dock for charging.
• Manual mode: In the pause state, press the button to activate the “return for charging” mode or use the controller or the smart APP for charging.
  

Automatic cleaning
Upon power on, the machine plans its cleaning route in a zigzag way and finishes cleaning the whole room in an orderly and efficient manner. Once cleaning ends, the machine will automatically return to the dock for charging (cleaning mode by default).

Spot cleaning
Use the button on the controller so that the machine will take itself as a center to sweep a round zone with the
diameter of 1.2 m. Upon cleaning, the robot will automatically return to the starting point and stop work.(The direction key on the smart APP can also be used to manually control the machine to the cleaning position.)

Scheduled cleaning
Use the smart APP to set the time for cleaning. The robot will start cleaning automatically at the scheduled time. Upon cleaning, it will return to the dock for charging (7 x 24 h scheduling supported)

Spot cleaning
Use the button on the controller so that the machine will take itself as a center to sweep a round zone with the
diameter of 1.2 m. Upon cleaning, the robot will automatically return to the starting point and stop work.(The direction key on the smart APP can also be used to manually control the machine to the cleaning position.)

Edge cleaning

•  For indoor cleaning, the machine normally sweeps along a fixed object (such as walls). Once cleaning finishes along all sides, it returns to the charging dock.
•  Press the button of on the controller or use the smart APP to quickly enable the side cleaning function.

Routine Maintenance

Roller brush (Recommended cleaning frequency: weekly)

1. Flip the machine, press the buckle on the roller brush cover, and remove the roller brush cover.
2. Remove the roller brush.
3. Use the cleaning brush that comes with the machine to remove.

Side brush (Recommended cleaning frequency: weekly)

1. Flip the machine, and pull out the side brushes vertically
2. Remove the entangled hair and dirt, and then reinstall the side brushes.
3. Align the left side brush (L) and right side brush (R) with the letters L and R on the bottom cover, and press the side brushes to reinstall them.
   

Clean the dust box  

1.  After the machine is used for a long time, remove the filter gauze and HEPA filter.
2. Put the removed pre-filter and dust box under the faucet for washing (the HEPA filter cannot be washed by water).
3.  Remove the water droplets, and dry the filter and dust box thoroughly before use.Press the switch of the dust box, open the dust box, and dump.

Upgrade the firmware
Start the smart phone app, and enter the firmware upgrade page. After the new firmware is detected, follow the
instructions to upgrade the firmware. To upgrade the firmware, the power must be equal to or greater than 50%. It is
recommended that you place the machine on the docking station for upgrade.

Battery

• Machine is equipped with a high-performance rechargeable lithium battery pack. To maintain battery performance, keep the machine in charging state in daily use.
•  If you do not use the machine for a long time, power it off and store it properly.Charge the machine at least once every 3 months to avoid damage to the battery due to excessive discharge.

Common Problems

Troubleshooting

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference.

REFERENCE LINK

https://www.laresar.us/