Monster MIR7.1082 Multi Color LED Flow Light Strip Operation Manual
Introduction
This Multi-color RB+IC LED flow light strip is easy to install, easy to use, and is ideal for adding ambient backlighting behind your TV or computer monitor for a great movie or gaming experience
Features
- Individual IC -controlled multicolor LEDs create dynamic flowing continuous lighting effects that move up and down the light strip, showing multiple colors at once
- Color changing and flash modes with controllable speed adjustment
- USB powered from any 5V/2A standard USB port
- Self-adhesive backing for easy application
- 13ft (4m) length, ideal for creating ambient backlighting behind a TV or monitor
- Remote control works up to 21 feet away
What’s Included
- 13ft Multicolor RGB+IC LED Flow Light Strip
- Micro USB Power Cable
- IR Remote Control with Battery (1 × 3V battery, CR2025)
- User Manual x1 pc
Safety Instructions
Please read and understand all instructions before using this product. If damage is caused by failure to follow the instructions, this warranty is null and void.
- Keep these instructions.
- Do not drop, puncture, or disassemble this product.
- Do not expose this product to dripping or splashing of drinks or liquids of any kind.
- Avoid long exposure to direct sunlight, which may cause damage.
- Do not expose this product to open flames.
- Do not use the product in a strong magnetic field.
- Use a clean, soft cloth to clean. Do not use any corrosive cleaners/oils to clean.
- Do not attempt to repair the device or open the unit as this will void the warranty.
Get Started
- Clean the surface you intend to stick the LED Light to
- Peel beginning of adhesive backing off and firmly stick LED Light onto the mounting surface (be careful to peel off only the backing and not the adhesive)
- Peel off more of the adhesive backing as you mount the LED Light, pressing and holding each section firmly against the surface
- Remove the tab from the battery compartment of the remote control
- Connect the controller unit to the LED light strip, be sure that the pins are lined up correctly
Connect the Micro USB connector of the power cable to the controller and connect the other end to a 5V 2A USB-A wall charger (not included)
Connect the Micro USB connector of the power cable to the controller and connect the other end to a 5V 2A USB-A wall charger (not included)Installation Notes:
- For best mounting results, place adhesive onto desired surface with ONE attempt. Reapplying multiple times will not guarantee secure mounting onto surface.
- Make sure the desired location is close enough to a power source like a TV’s USB port or a wall outlet with a 2A USB adapter (not included)
- For optimal performance, place IR receiver in a location away from the IR receiver on the TV to avoid interference from the TV remote control signal
- For backlighting a TV or monitor, follow the mounting diagram below:
At a Glance
IR Remote Operation
- Turn on the LED Light by pushing the ON button on the remote control
- Select the desired color or the desired effect by pushing the corresponding button on the remote control
- Set the desired brightness using the buttons to increase/decrease the intensity of color
- Push the OFF button to turn off the LED Light
Changing the remote control battery:
The battery for the remote control has already been installed. Remove the battery pull tab to operate.
- The battery compartment is located on the narrow side of the remote control
- Remove the empty battery and insert a 3V battery, type CR2025, with the positive terminal pointing upwards
- Place the battery compartment back in the remote control so it locks in place
Customer Service
In the event this product becomes defective, please do not return this product to your retailer.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s warranty or authority to operate the equipment. The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed or mobile condition. The minimum separation distance is 20cm.
Battery cautions:
Coin / Button Cell Battery Cautions:
- Keep batteries out of reach or small children or those that require supervision. Should a child, or someone, swallow a battery, consult a physician immediately.
- Dispose of batteries following your local regulations.
- When discarding batteries, insulate the + and – terminals with a piece of insulating tape. When disposed of improperly, lithium batteries may short and pose a hazard.
- Keep batteries away from direct sunlight, high temperature, and high humidity
Specifications
- LED Light (USB): 5V 2A
- output: 9W
- length: 13ft
- remote control: battery 3V coin cell (1 × 3V battery, type CR2025)
DOWNLOAD PDF LINK
6679bb6844d06d42e9d7ba39a8377b8ae472deb55273208968b5e7bb1f5c9214_optim
