Morecam J1 Smart Video Doorbell User Instructions

Morecam J1 Smart Video Doorbell User Instructions

 What’s in the box

Meet the doorbell

1. 2MP camera
2. Motion sensor
3. Speakers
4. Doorbell button
5. LED indicator
6. Charging indicator
7. Micro-USB port
8. Reset hole
9. Security screw hole
10. Microphone
11. Power contacts
12. Hardwire terminals
13. Micro-SD card slot
14. 18650 Battery pack
15. Security screw
16. Mounting screw holes

 Meet the Chime

1. Speakers
2. Reset
3. LED Indicator
4. USB Port (Type-A/M)

Battery Installation

The batteries are pre-installed in the doorbell, with an insulation film inserted in the positive poles. Please remove the film and insert the battery pack back to compartment, with positive poles upwards!

NOTE:
Improper battery installation will cause damage to the internal components and may result in serious injury.

Battery Charging

The batteries inside the doorbell are not fully charged in accordance with transportation safety regulations. Please charge the batteries with a USB compatible wall charger (not included) and the provided USB cable for about 8~10 hours prior to installation.

Wi-Fi Set Up

Before you start the Wi-Fi configuration, please note below:

1. The doorbell works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi.
2.  Avoid using special characters or symbols like )(@~!#$%^&*…, either in your Wi-Fi name or password.
3. Perform the configuration near your Wi-Fi router

Launch the ‘CloudEdge’ App and register an account with your mobile phone number or email ID. Start the Wi-Fi configuration, following the in-App instructions or refering to the following guiding steps.

Guiding steps:

Run a Test

After setup, tap on the live view window in the App for a test. Then take your doorbell outside to the installation spot and run a test there. Make sure the installation spot is covered by strong 2.4 GHz Wi-Fi signal.

Note:
If the video quality from the doorbell outside is not as good as it was indoors, you may need to move your router closer to your installation spot, or invest in an Wi-Fi extender.

 Live viewing

1. Quit live viewing
2. Setting menu
3. Volume on/off
4. HD/SD switch
5. Full screen display
6. Stream bit rate
7. Wi-Fi signal status
8. Battery status
9. Screenshot button
10. Speak to the visitor
11. Record on the phone
12. Motion detection on/off
13. Photo Album
14. Video Playback
15. Cloud storage service

Playback

If the Micro-SD card is properly installed, you can playback the video clips taken after detected motions or visitor calls. (Live viewing will not trigger device recording). You can also back up video clips to the cloud, only if you have activated the cloud storage service (7-Days-Free Trial available).

Share Your Device

sharing by account searching

Steps: Settings>>Device Share>>Tap on “Add ”>>Tap on “Account”>>Type in account ID>>Confirm Sharing.

Sharing by QR code scanning
The new users can show their QR codes to the administrator, and share device by QR Code scanning.

Find your QR code: Run CloudEdge App >> Tap on “ ” >> “User Name” >> “My QR Code” >> Let the administrator scan your QR Code

NOTE:

1.  Guide your family members to download and install the CloudEdge App, and register an account prior to device-sharing.
2.  There is no limitation on the number of users sharing one device.
3.  Only the adminstrator got access to the setting menu. Other users can only live view & playback.
4. All users will receive doorbell calls and alarm notifications.
5. Many users can access to the doorbell simultaneously, to live view or playback.

Connect the Chime

1. Supply Power to the Chime
   The chime can be powered by an USB compatible phone charger (DC5V 1A). You can also plug the chime to the USB port on your PC/notebook to supply power.
2. Click reset button:
   Click the RESET button on the wireless chime only once, and you will see the LED indicator flashing blue, indicating the chime is in pairing mode.
3. Press the doorbell button:
   Press the doorbell button, and the Chime will sound to react. Pairing succeeds, and the indicator on the chime will be in solid blue.
   
4.  chime settings:
   You can enter into the chime setting page following below setting steps, so as to mute the Chime Reminder, select ringtones, adjust chime volume or unbind the connection with doorbell.

NOTE:
1. Your doorbell communicates with the chime via Radio Frequency, but not WiFi. You can even do the pairing prior to doorbell configuration.
2. You can add many chimes to one doorbell, and vice versa.
3. Press and hold RESET button on the chime for 5 seconds till the indicator flashes blue 3 times, and you can also release the connection between the chime and its connected doorbell.

Installation

Select location
Your doorbell has 166-degree view angle and 120-degree human detection range. It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance.

Hardwire your doorbell (Optional)
The doorbell works with both 12V ~ 24V AC and 12V DC hardwire power source. Either wire can be connected to either terminal. The cable order doesn’t matter.

1. (Optional) Shut off power at the breaker,remove the old doorbell from the wall and disconnect the wires.
2. Connect the wires to the screw terminals on your mounting bracket. Either wire can be connected to either terminal.
3. (Optional) The nameplate holder can be mounted on the top rear/ bottom rear of the bracket, prior to bracket installation.
4. Drive the screws into the anchors, or directly into your wall until the bracket is tightly fastened on your wall.
5. (Optional) You can also use the provided double-sided tape instead of screws to fix the wall mount on flat surface.
6. Mount the doorbell to the bracket, and secure it with the provided star-shape security screw and screw driver. All set!

Specification

Video doorbell

• Image Sensor: 1/2.7” CMOS (2.0 MP)
• OS: Lite-OS
• Resolution: 1920 × 1080 px
• Stream: HD/SD dual stream
  
• Infrared LED: High power IR LED with ICR
  
• Lense: 1.7 mm/F2.0
  
• Angle of view: 166°
  
• Min. illumin: Digital WDR
  
• WDR: 2-way audio with noise cancellation

Storage:

• Storage Type: Micro SD Card (Max 128G)
  
• Cloud storage: Support
  
• Recording: Triggered by PIR motion sensor

Network:

• Wifi Frequency: 2.4 GHz ~ 2.4835 GHz
• Standards: IEEE 802.11 b/g/n
• Live View Speed: Triggered by PIR motion sensor

Troubleshooting

•  How do I know if I have 2.4G or 5G wifi?
  Please check the user manual of your Router or call the network operator for help.
•  It has to be on same WiFi to see the camera, or is it over internet from anywhere?
  You can view the camera from anywhere, if your camera is well connected to the internet.
• Do any of the recordings get saved to the cloud? Or is it mainly saved in the built-in SD card?
  It supports SD card recording as well as cloud storage. You can activate the cloud storage service in App.
• What happens when the SD is full?
  When the memory card is full, the camera automatically erase the oldest footage
•  Can we have 2 or more doorbells at the same residence?
  Yes, you can add more than one device at the same residence

REFERENCE LINK

https://www.morecam.cn/