Pheanoo P15 2.1CH Soundbar with Subwoofer Manual
IMPORTANT SAFETY INSTRUCTIONS
Your Unit is designed and manufactured to operate within defined design limits, and misuse may result in electric shock or fire. To prevent your Unit from being damaged, the following rules should be observed for its installation, use, and maintenance. Please read the following safety instructions before operating your Unit. Keep these instructions in a safe place for future reference.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings.Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. - Protect the power cord from being walked on or pinched, particularly at plugs,convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod,bracket, or table specified by the manufacturer, or sold with the apparatus.
- When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
What’s in the box
USE YOUR SOUNDBAR SYSTEM
How to control your soundbar
POWER Turns on the Sound Bar or sets it to standby mode.
MUTE Turns off the sound temporarily or turns on the sound
VOL+ Increase volume
VOL Decrease volume
RESET(PLAY/PAUSE) Start, pause or resume play in BT Mode Press and hold for about 2 seconds to reset the volume level and switch to the Movie EQ effect.
BASS+ Increase bass level
BASS Decrease bass level
TV ARC Set the input source for the Soundbar to HDMI ARC mode
BT Set the input source for the Soundbar to Bluetooth mode
AUX Set the input source for the Soundbar to AUX mode
OPT Set the input source for the Soundbar to Optical mode
MUSIC Selects MUSIC for the sound effect
MOVIE Selects MOVIE for the sound effect
DIALOGUE Selects DIALOGUE for the sound effect
INDICATOR Turns on/off the indicators on the Bar Speaker.
Remote Control Battery Replacement
| Model | P15 |
| Function | BT/AUX/HDMI(ARC)/OPT |
| Drivers | 2.25″*2 SB+ 4″*1 SW |
| Frequency Response | 45Hz-20KHz |
| Signal-to-Noise Ratio | 107dB |
| lmpedance | 6Ω*2+4Ω*1 |
| Max Output Power | 140W |
| Power lnput | 110V-240V~50Hz/60Hz 1A |
| Bluetooth Version | Version: 5.0 Range: up to 10m |
| Dimensions | Soundbar: 405*97*75mm Subwoofer: 140*200*360mm |
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).
