Ozeri PD4X3-2 4x3razor Pocket 3D Pedometer User Manual
Product Overview
Getting Started
Before using your 3D Pedometer for the first time (or after changing the battery), you will need to set it up so that it is personalized to you by following the instructions below.
- Remove the battery tab from the pedometer by pulling the tab outwards. This will automatically begin the setup process with the TIME screen.
- Program each screen using the Mode and Reset buttons to increase and decrease the digits respectively. Use the Set button to confirm each entry.
- If a button is not pressed within 60 seconds, the pedometer will exit Setup Mode, and the screen will turn off. If this happens, apply a pin to the hole on the back of the pedometer to perform a System Reset.
Programming your Pedometer:
- TIME: Press MODE to switch from 24 HR and 12 HR clock display. Press SET to confirm entry. Continue to program HOUR and MIN as follows. Press MODE to advance by 1. For rapid advance, press and hold MODE for over 2 seconds. Press RESET to decrease by 1. To decrease rapidly, press and hold RESET for over 2 seconds. Press SET to confirm the TIME.
- USA (Imperial) or International (Metric) Symbols: Press MODE to switch from Imperial to Metric units of measurement. NOTE: Changing the unit of measurement will reset the pedometer’s programming and delete all recorded exercise data.
- STRIDE: After programming the CLOCK, the screen will flash the default STRIDE length (default value is 3 feet. Range is 1 to 6 feet). (default value is 70 cm. The range is 30 to 180 cm)
Press MODE to advance by 0.25 feet (or 1 cm). Press RESET to decrease by 0.25 feet (or 1 cm). To advance or decrease rapidly, press and hold MODE or RESET respectively for over 2 seconds. Press SET to confirm your STRIDE. - WEIGHT: After programming the CLOCK, the screen will advance to WEIGHT (default value is 150 lbs. Range is 45 to 350 lbs). (default value is 60 kg. The range is 20 to 160 kg)
Press MODE to advance by 1 lb (or 1 kg). Press RESET to decrease by 1lbs (or 1 kg). and hold MODE or RESET respectively for over 2 seconds. Press SET to confirm your WEIGHT. This completes the programming. Your pedometer will default to the STEP and TIME screen for TODAY.
NOTE:
The pedometer can be reprogrammed at any time (except under TOTAL STEPS & 30 days memory mode) by pressing SET for over 3 seconds. Reprogramming the pedometer will not erase the 30-Day and TOTAL STEP memory.
Memory Mode
Your pedometer can store up to 30 days of data for steps walked, calories consumed, and distance traveled. At 12:00 a.m. the LCD resets to zero and the previous day’s data is automatically stored in memory. Even though the daily memory is reset at midnight, the pedometer will still add each day’s detailed data into its 30-day memory. In addition, the pedometer will also store the steps walked for up to 999,999 steps or 99 days on its TOTAL Step screen. Viewing the data stored in memory:
From either the DISTANCE OR CALORIES screen, press the SET button to view historical data.
Once in Memory Mode, press the MODE button between the STEP, CALORIES, and DISTANCE screens.
Press the RESET button to cycle back into historical data by day.
Total Memory Mode
Total Memory Mode shows the total steps captured for up to 99 days or 999,999 steps. Press the MODE button until the screen displays TOTAL on the bottom right
NOTE:
When the TOTAL MEMORY reaches 999,999 steps and/or 99 days, the pedometer will stop counting steps. A RESET must be performed from the TOTAL MEMORY screen. Please refer to the warm RESET instructions.
Reseting the Pedometer (warm reset)
From any of the following display views, press and hold the RESET button for over 5 seconds to reset the pedometer. All exercise data except TOTAL STEPS & 30 days memory will be reset to zero.
When the TOTAL MEMORY reaches 999,999 steps and/or 99 days, the pedometer will stop counting steps. A TOTAL MEMORY reset must be performed. Switch to the TOTAL MEMORY screen display, then press and hold the RESET button for 5 seconds. This will erase all exercise data stored in the pedometer (excluding TIME, STRIDE, and WEIGHT setup data). Whereas a warm reset only erases exercise data, a cold reset erases all exercise and setup data stored in the pedometer, restoring the pedometer to its original factory-set programming.
Performing a Cold Reset
A cold reset is required if all data needs to be deleted or if the display becomes unrecognizable.
NOTE:
To perform a cold reset, insert a blunted pin into the RESET hole on the back of the pedometer. The pedometer will have to be programmed before use. Please refer to the Setup instructions. The battery needs to be changed when the LCD begins to dim and the screen digits become difficult to read. Refer to the following diagram when changing the battery.
Replacing the Battery
- Remove the screw from the back of the pedometer.
- Pull the battery slot out of the pedometer.
- Replace the battery with a new CR2025 battery
- Program the TIME, STRIDE, and WEIGHT as per the instructions in the GETTING STARTED section.
NOTE:
If the pedometer is not programmed after a cold reset, or if no activity is detected immediately after a cold reset, the pedometer will deactivate. Perform a cold reset again by inserting a blunted pin into the hole on the back of the pedometer. When changing the battery all current data stored under TODAY will be reset to 0. The pedometer will still retain 30 days of historical data as well as the TOTAL step memory.
WARRANTY INFORMATION
Your 4×3 razor Pedometer, by Ozeri, is warranted to the original owner for 1 year from the date of purchase against defects in material and workmanship under normal use and service. Should your Pedometer prove defective within 1 year from the date of purchase, return the defective product, freight prepaid along with an explanation of the claim to “Ozeri.” Please pack your Pedometer carefully to avoid damage in transit.
Under this warranty, Ozeri will repair or replace any parts found to be defective due to a manufacturer’s defect. This warranty extends only to personal use and does not extend to any product that has been used for commercial use, rental use, or use that is not intended. There are no warranties other than that expressly set forth herein. This warranty is not transferable.
Ozeri is not responsible in any way for damages, losses, or inconveniences caused by equipment failure or by user negligence, abuse, or use not in accordance with the “User Guide” or any additional safety, use, or warnings included in the product materials. Further, Ozeri is not liable for incidental or consequential damages of any nature resulting from the use of this product and any liability shall not exceed the purchase price of the product.
REFERENCE LINK
https://ozeri.com/bath-and-personal-care/Ozeri-4x3razor-Pedometer-Activity-Technology/B005G00AH2
