Philips TAT1138 Headphones 1000 Series User Manual
Important safety instructions
Hearing safety
Danger
- To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.
Be sure to observe the following guidelines when using your headphones.
- Listen at reasonable volumes for reasonable periods of time.
- Be careful not to adjust the volume continuously upwards as your hearing adapts.
- Do not turn up the volume so high that you can’t hear what’s around you.
- You should use caution or temporarily discontinue use in potentially hazardous situations.
- Excessive sound pressure from earpieces and headphones can cause hearing loss.
- Using headphones with both ears covered while driving is not recommended and may be illegal in some areas.
- For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.
General information
To avoid damage or malfunction:
Caution
- Do not expose headphones to excessive heat.
- Do not drop your headphones.
- Headphones shall not be exposed to dripping or splashing. (Refer to the IP rating of specific product)
- Do not allow your headphones to be submerged in water.
- Do not charge your headphones when the connector or socket is wet.
- Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
- If cleaning is required, use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
- The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
- To achieve the specific IP rating, the charging slot cover must be closed.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
- To avoid risk of fire, the equipment is supplied only by external power source which output shall comply with PS1 (with output capacity less than 15W)
Operating and storage temperatures and humidity
- Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) with up to 90% relative humidity.
- Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) with up to 90% relative humidity.
- Battery life may be shorter in high or low temperature conditions.
- Replacement of a battery with an incorrect type risks severely damaging the headphones and the battery (for example, in the case of some lithium battery types).
Your True wireless earpieces
Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips offers, register your product at www.philips.com/support. With these Philips True wireless earpieces you can:
- Enjoy convenient wireless handsfree calls
- Enjoy and control music wirelessly
- Switch between calls and music
What’s in the box
Other devices
A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible with the earpieces.
Overview of your True wireless earpieces
Get started
Charge the battery
Note
- Before you use your headphones, place them in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime.
- Use only the original USB-C charging cable to avoid any damage.
- Finish your call before charging. Connecting the earpieces to charge will power them off.
- If the headset is not used for a long time, the rechargeable battery will begin to lose its charge. To avoid this loss, please fully charge the battery at least once every three months.
Earpiece
Take out the earpieces and remove the insulation labels. Put the earpieces back into the charging case and close the lid, the earpieces then start charging.
Tip
- Normally, a full charge takes 2 hours (for the earpieces or charging case) by USB cable.
Charging case
Plug one end of the USB-C cable into the charging case and the other end into the power source.
Tip
- The charging case serves as a portable backup battery for charging the earpieces. When the charging case is fully charged, it will fully recharge the earpieces 3 times.
How to wear
Insert the earpieces
- Check left or right orientation of the earpieces.
- Insert the earpieces into the ears and twist slightly until a secure t is achieved.
Pair the earpieces with your Bluetooth device for the first time
- Make sure that the earpieces are fully charged and powered off.
- Open the cover of the charging case. Take the earpieces out.
- The LEDs on both earpieces ash white and blue alternately
- The earpieces are now in pairing mode and are ready to pair with a Bluetooth device (e.g. a mobile phone)
- Turn on the Bluetooth function of your Bluetooth device.
- Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.
Note
- After powering on, if the earpieces cannot nd any previously connected Bluetooth device, it will automatically switch to pairing mode.
The following example shows you how to pair the earpieces with your Bluetooth device.
- Turn on the Bluetooth function of your Bluetooth device, select Philips TAT1138.
- Enter the earpieces’ password “0000” (4 zeros) if prompted. For those devices featuring Bluetooth 3.0 or higher, there is no need to enter a password.
Single earpiece (Mono mode)
Take either right or left earpiece out from charging case for Mono use. The earpiece will power on automatically.
Note
- Voice assistant is disabled in Mono mode.
- Take the second earpiece from the charging case and they will pair with each other automatically.
Pair the earpieces with another Bluetooth device
If you want to pair another Bluetooth device with the earpieces, just press and hold MFB on both earpieces 5 seconds into pairing mode and put back in the charging case, then re-take out from the charging case, discover the second device as per normal pairing.
Note
- The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.
Use your earpieces
Connect the earpieces to your Bluetooth device
- Turn on the Bluetooth function of your Bluetooth device.
- Take out earpieces from the charging box cover.
- The blue LED ashes
- The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earpieces will enter pairing mode
Tip
- The earpieces can’t connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
- If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.
Note
- If the earpieces fail to connect to any Bluetooth device within 3 minutes, it will turn off automatically to save the battery life.
- In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually.
Power on/off
Manage your calls and music
Voice Assistant
Earpieces LED indicator status
Charging box LED indicator status
Reset the earpieces
If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default settings.
- On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT1138 from the device list.
- Turn off the Bluetooth function of your Bluetooth device.
- Take the earpieces out of the charging case and press the button once, then press and hold for 5 seconds.
- Return the earpieces to the charging case.
- Follow steps in “Use your earpieces connect the earpieces to your Bluetooth device.”
- Pair the earpieces with your Bluetooth device, select Philips TAT1138.
Technical data
- Music play time: 5+10 hours
- Charging time: 2 hours
- Lithium-ion battery 30 mAh on each earpiece, Lithium-ion battery 250 mAh on charging box
- Bluetooth version: 5.3
- Compatible Bluetooth profiles:
- HFP (Hands-Free Profile)
- A2DP (Advanced Audio Distribution Profile)
- AVRCP (Audio Video Remote Control Profile)
- Supported audio codecs: SBC
- Frequency range: 2.402-2.480 GHz
- Transmitter power: < 10 dBm
- Operating range: Up to 10 meters (33 feet)
- USB-C port for charging
- Low battery warning: available
Note
- Specifications are subject to change without notice.
Notice
Declaration of conformity
Hereby, MMD Hong Kong Holding Limited declares that the product is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. You can find the Declaration of Conformity on www.philips.com/support.
Disposal of your old product and battery
Your product is designed and manufactured with high quality materials and components which can be recycled and reused.
This symbol on a product means that the product is covered by European Directive 2012/19/EU.
This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.
Remove the integrated battery
If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces.
- Make sure the earpieces are disconnected from the charging box before removing the battery.
- Make sure the charging box is disconnected from the USB charging cable before removing the battery.
Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Notice of compliance
The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Trademarks
Bluetooth
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.
Siri
Siri is a trademark of Apple Inc., registered in the U.S. and other countries.
Google and Google Play are trademarks of Google LLC.
DOWNLOAD PDF LINK
