Philips TAT3255 Headphones 3000 Series User Manual
Important safety instructions
Hearing Safety
- To avoid hearing damage, limit the time you use headset at high volume and set the volume to a safe level. The louder the volume the shorter the safe listening time is.
Be sure to observe the following guidelines when using your headset.
- Listen at reasonable volumes for reasonable periods of time.
- Be careful not to adjust the volume continuously upwards as your hearing adapts.
- Do not turn up the volume so high that you can’t hear what’s around you.
- You should use caution or temporarily discontinue use in potentially hazardous situations.
- Excessive sound pressure from earphones and headset can cause hearing loss.
- Using headset with both ears covered while driving is not recommended and may be illegal in some areas while driving.
- For your safety, avoid distractions from music or phone calls while in environments.
General information
To avoid damage or malfunction
Caution
- Do not expose headset to excessive heat.
- Do not drop your headset.
- Headset shall not be exposed to dripping or splashing.
- Do not allow your headset to be submerged in water.
- Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
- If cleaning is required use a soft cloth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.
- The integrated battery shall not be exposed to excessive heat such as
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
About operating and storage temperatures and humidity
- The storage temperature is between -10°C to 65 °C. The operation temperature is 45°C (max.) (up to 90% relative humidity).
- Battery life may be shorter in high or low temperature conditions.
Your Bluetooth wireless headset
Congratulations on your purchase, and welcome to Philips! To fully benefit from the product at www.philips. com/welcome. With this Philips wireless headset, you can:
- enjoy convenient wireless handsfree calls;
- enjoy and control wireless music；
- switch between calls and music.
What’s in the box
Other devices
A mobile phone or device (e.g. notebook, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset (see ‘Technical data” on page 10).
Overview of your Bluetooth wireless headset
Get started
Charge the battery
- Before use place the headsets in the charging case and charge the battery for 3 hours for optimum battery capacity and lifetime.
- Use only the original USB charging cable to avoid any damage.
- Finish your call before charging the headset, as connecting the headset for charging will power the headset off.
Charging case
Connect one end of the USB cable into the charging case, and another end into the power source.
- The charging case starts charging.
- Charging process is verified by the blue LED light on the front panel.
- When the charging case is fully charged, the blue light goes on.
Tip
- The charging case serves as a portable backup battery for charging the headset. When the charging case is fully charged, it supports 3 full recharge cycle for the headset.
Headset
Place the headset in the charging case.
- The headset start charging.
- Charging process is veried by white LED lights on the earpieces.
- When the headset is fully charged. the white light goes off.
Tip
- Normally, a full charge takes 2 hours (for the headset or charging case).
Pair the headset with your Bluetooth device at the first time
- Make sure that the headset is fully charged.
- Take both headsets from the charging case, the headset will power on automatically, entering pairing model and Right & Left headset connected.
- here will be a voice “Power on” and a voice “Pairing”. Then, there will be a voice” Right channel” on right headset and “Left Channel” on left headset after paring each other.
- In right headset, it has voice “Pairing” and LED ashes in white and blue. The headset is now in pairing mode and is ready to pair with a Bluetooth device (e.g. a mobile phone).
- Turn on the Bluetooth function of your Bluetooth device.
- Take the right headset (“Master device” ) from the charging case, the earpiece will power on automatically.
- There will be a voice “Power on” from right headset.
- Turn on the Bluetooth function on your device, search for “Philips TAT3215, TAT3255” tap to connect. ( Please refer to P.6 ) Once the pairing succeed, you will hear a voice” connected” And the
- Pair the headset with your Bluetooth device. Refer to the user manual of your Bluetooth device.
- In right headset, it has voice “Connected” and LED stays on for 5 seconds on both headsets. You can use your device to play music or make a call.
Note
- Only Turn the “Left headset channel power on, it cannot connect to Bluetooth device, need to turn on “Right Channel” to pair each other.
The following example shows you how to pair the headset with your Bluetooth device.
- Turn on the Bluetooth function of your Bluetooth device, select Philips TAT3215, TAT3255
- Enter the headset password “0000” (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.
Single headset pairing (Mono mode)
- Take the right headset (“Master device” ) from the charging case, the earpiece will power on automatically. There will be a voice “Power on” from right headset.
- Turn on the Bluetooth function on your device, search for “Philips TAT3215, TAT3255” tap to connect. ( Please refer to P.6 )
- Once the pairing succeed, you will hear a voice” connected” And the indicator light will be off.
Note
- Only Turn the “Left headset channel power on, it cannot connect to Bluetooth device, need to turn on “Right Channel” to pair each other.
Pair the headset with another Bluetooth device
If you have another Bluetooth device that you want to pair with the headset make sure the Bluetooth function in any other previously paired or connected steps in ‘Pair the headset with your Bluetooth device at the rst time’. ‘Pair the headset with your Bluetooth device at the first time’.
Note
- The headset stores 1 device in the memory. If you try to pair more than 2 devices the earliest paired device is replaced by the new one.
Use your headset
Reconnect the headset to your Bluetooth device
- Turn on the Bluetooth function of your Bluetooth device.
- Take both headsets from the charging case, the headset will power on and reconnect automatically.
- If no device is connected, the headset will automatically turns off after 3 mins
- Both headsets are now powered on and are paired with each other automatically.
- The headset will search the last connected Bluetooth device and reconnect to it automatically. If the last connected one is not available, the headset will search and reconnect to the second last connected device.
Tip
- The headset cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
- If you turn on the Bluetooth function of your Bluetooth device after turning on the headset, you have to go to the Bluetooth menu of the device and connect the headset to the device manually
Note
- If the headset fails to connect to any Bluetooth automatically to save the battery life.
- In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the headset to the Bluetooth device manually.
Power On/Off
Manage your calls and music
LED indicator status
Battery LED indicator on headset status
It will show a battery indicator on Bluetooth device after connected to headset.
Battery LED indicator on Charging case
While charging headset, Blue LED will light on
- 4 blue LED lights stay on for 75-100% power
- 3 blue LED lights stay on for 50-75% power
- 2 blue LED lights stay on for 25-50% power
- 1 blue LED lights stay on for 0-25% power
Battery LED indicator on Charging case with USB Type-C cable
While charging headset, Blue LED status as below:
- 4 blue LED stay on for 70-100% power
- 2 blue LED stay on and 3rd LED flashes every second for 50-75% power
- 1 blue LED stays on and 2nd LED flashes every second for 25-50% power
- 1 blue LED ashes every second for 0-25% power
How to wear
Factory reset the headset
If you encounter any pairing or connection issue, you can follow the following procedure to factory reset your headset.
- On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT3215 from the device list.
- Put both headset back to charging case. Hold and press left & right headsets function button for 5 seconds.
- Turn off the Bluetooth function Bluetooth device.
- Take both headsets from the charging case, the headset will power on automatically. There will be a voice “Power on” and a voice ” Pairing”.
- Then, there will be a voice” Right channel” on right headset and “Left Channel” on left headset after paring each other. The LED on Right headset ashes in white and blue for 3 mins. There will be a voice “Connected” from Right Channel.
- Then, the right headset LED earpiece flashes in white and blue for 3 mins.
- To pair the headset with a Bluetooth device, turn on the Bluetooth function of your Bluetooth device, select Philips TAT3215, TAT3255.
Technical data
Headset
- Music time: 6 hours (additional 18 hrs wiht charging case)
- Talk time: 5 hours (additional 15 hrs with charging case)
- Standby time: 80 hours
- Charging time: 2 hours
- Rechargeable lithiumion battery: 50 mAH on each earpiece
- Bluetooth version: 5.1
- Compatible Bluetooth proles:
- HSP (Hands-Free Prole-HFP)
- A2DP (Advanced Audio Distribution Profile)
- AVRCP (Audio Video Remote Control Profile)
- Supported audio codec: SBC
- Frequency range: 2.4 GHz
- Transmitter power: <4 dBm
- Operating range: Up to 10 meters (33 feet)
Charging case
- Charging time: 2 hrs
- Rechargeable Li-ion battery: 500mAh
Note
- Specification are subject to be change without notice.
Notice
Declaration of conformity
Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can nd the Declaration of Conformity on www.p4c.philips.com.
Disposal of your old product and battery
Your product is designed and manufactured with high quality materials and components, which can be recycled and resused
This symbol on a product means that the product is covered by European Directive 2012/19/EU.
This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste .We strongly advise you to take your product service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.
Remove the integrated battery
If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headset.
- Make sure the headset is disconnected from the charging case before removing the battery.
- Make sure the charging case is disconnected from the USB charging cable before removing the battery.
Compliance with EMF
This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
Notice of compliance
The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Trademarks
Bluetooth
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Top Victory Investment Limited is under license. Other trademarks and trade names are those of their respective owners.
Siri
Siri is a trademark of Apple Inc., registered in the U.S. and other countries.
Google and Google Logo are registered trademarks of Google Inc.
DOWNLOAD PDF LINK
https://www.philips.com.sg/c-p/TAT3255PP_00/in-ear-true-wireless-headphones
