Philips-TAT5506-Headphones-5000-Series-FEATURE

Philips TAT5506 Headphones 5000 Series User Manual

Philips-logo

Philips TAT5506 Headphones 5000 Series User Manual

Philips-TAT5506-Headphones-5000-Series-IMG

Important safety instructions

Hearing safety

Philips-TAT5506-Headphones-5000-Series-Fig1

Danger

  • To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is.
  • Be sure to observe the following guidelines when using your headphones.
  • Listen at reasonable volumes for reasonable periods of time.
  • Be careful not to adjust the volume continuously upwards as your hearing adapts.
  • Do not turn up the volume so high that you can’t hear what’s around you.
  • You should use caution or temporarily discontinue use in potentially hazardous situations.
  • Excessive sound pressure from earpieces and headphones can cause hearing loss.
  • Using headphones with both ears covered while driving is not recommended and may be illegal in some areas.
  • For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.
General information

To avoid damage or malfunction:

Philips-TAT5506-Headphones-5000-Series-Fig1Caution

  • Do not expose headphones to excessive heat.
  • Do not drop your headphones.
  • Headphones shall not be exposed to dripping or splashing. (Refer to the IP rating of specic product)
  • Do not allow your headphones to be submerged in water.
  • Do not charge your headphones when the connector or socket is wet.
  • Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.
  • Use a clean, damp cloth to clean your headphones – especially the sound conduits and the microphone holes – regularly and avoid buildup of substances such as sweat or earwax.
  • If any sweat or water droplets are left in the sound conduits, air holes or microphone holes, the sound level will temporarily drop or cut out entirely. This is not a malfunction. Use a soft, damp cloth to dry the headphones thoroughly. Alternatively, remove the earbud tips, turn the sound conduits downward and gently tap the headphones about ve times on a dry cloth or similar to remove any water collected inside.
  • Be sure the headphones are completely dry before charging and using. Avoid using disposable alcohol pads or other substances for cleaning.
  • The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like.
  • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
  • To achieve the specific IP rating, the charging slot cover must be closed.
  • Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion.
  • Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
  • A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
  • Replacement of a battery with an incorrect type risks severely damaging the headphones and the battery (for example, in the case of some lithium battery types).
  • If the headset is not used for a long time, the rechargeable battery will begin to lose its charge. To avoid this loss, please fully charge the battery at least once every three months.
  • To avoid risk of fire, the equipment is supplied only by external power source which output shall comply with PS1 (with output capacity less than 15W).
Operating and storage temperatures and humidity
  • Store in a place where the temperature is between -20°C (-4°F) and 50°C (122 °F) with up to 90% relative humidity.
  • Operate in a place where the temperature is between 0°C (32°F) and 45°C (113 °F) with up to 90% relative humidity.
  • Battery life may be shorter in high or low temperature conditions.

Your True wireless earpieces

Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With these Philips True wireless earpieces you can:

  • Enjoy convenient wireless handsfree calls
  • Enjoy and control music wirelessly
  • Switch between calls and music

What’s in the box

Philips-TAT5506-Headphones-5000-Series-Fig2

Other devices

A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible with the earpieces.

Overview of your True wireless earpieces

Philips-TAT5506-Headphones-5000-Series-Fig3

Charge the battery

Philips-TAT5506-Headphones-5000-Series-Fig4Note

  • Before you use your headphones, place them in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime.
  • Use only the original USB-C charging cable to avoid any damage.
  • Finish your call before charging. Connecting the earpieces to charge will power them off.

Charging Box

Plug one end of the USB-C cable into the charging box and the other end into the power source.

Philips-TAT5506-Headphones-5000-Series-Fig6

Philips-TAT5506-Headphones-5000-Series-Fig5Tip

  • The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it will fully recharge the earpieces 3 times.

Earpieces

Place the earpieces in the charging box.

  • The earpieces start charging and the blue LED light goes on
  • When the earpieces are fully charged, the blue light will go off

Philips-TAT5506-Headphones-5000-Series-Fig7

Philips-TAT5506-Headphones-5000-Series-Fig5Tip

  • Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable.

Wireless charging

The charging box has a built-in wireless charging coil. You can charge the battery by using a wireless charger or another device that functions as a wireless charger.

Philips-TAT5506-Headphones-5000-Series-Fig1Caution

  • Precautions for wireless charging
  • Do not place the charging box on the wireless charger when conductive materials, such as metal objects and magnets, are placed between the charging box and the wireless charger.
  • Keep the charging box away from high temperatures and water sources. The box may get warm during charging. This is normal.

Charging the battery with a wireless charger.

  • Place the earpieces in the charging box
  • Close the charging box cover
  • Place the charging box on the center of the wireless charger
  • When fully charged, remove the charging box from the wireless charger

Philips-TAT5506-Headphones-5000-Series-Fig8

Philips-TAT5506-Headphones-5000-Series-Fig5Tip

  • A full charge takes 4 hours by wireless charging.

How to wear

Select suitable ear tips for optimum fit A tight, secure fit will provide the best sound quality and noise-cancellation.

  • Test which ear tip provides you with the best sound and wearing comfort.
  • sizes provided – large, medium and small.

Philips-TAT5506-Headphones-5000-Series-Fig9

Insert the earpieces

  • Check left or right orientation of the earpieces.
  • Insert the earpieces into the ears and twist slightly until a secure t is achieved.

Philips-TAT5506-Headphones-5000-Series-Fig10

Pair the earpieces with your Bluetooth device for the first time

  • Make sure that the earpieces are fully charged and powered o.
  • Open the top cover from charging box.

Philips-TAT5506-Headphones-5000-Series-Fig11

  • The LEDs on both earpieces flash white and blue alternately
  • The earpieces are now in pairing mode and are ready to pair with a Bluetooth device (e.g. a mobile phone)
  • Turn on the Bluetooth function of your Bluetooth device.
  • Pair the earpieces with your Bluetooth device. Refer to the user manual of your Bluetooth device.

Philips-TAT5506-Headphones-5000-Series-Fig4Note

  • After powering on, if the earpieces cannot nd any previously connected Bluetooth device, it will automatically switch to pairing mode.

The following example shows you how to pair the earpieces with your Bluetooth device.

  • Turn on the Bluetooth function of your Bluetooth device, select Philips TAT5506.
  • Enter the earpieces’ password “0000” (4 zeros) if prompted. For those devices featuring Bluetooth 3.0 or higher, there is no need to enter a password.

Philips-TAT5506-Headphones-5000-Series-Fig12

Single earpiece (Mono mode)

Take either right or left earpiece out from charging box for Mono use. The earpiece will power on automatically. You will hear a voice from the earpieces saying “Power on”.

Philips-TAT5506-Headphones-5000-Series-Fig4Note

  • Take the second earpiece from the charging box and they will pair with each other automatically.

Pair the earpieces with another Bluetooth device

If you want to pair another Bluetooth device with the earpieces, make sure the Bluetooth function in any other previously paired or connected devices is turned off. Long press the button of charging box for about 3 seconds when earpieces flash in white & blue alternately.

Philips-TAT5506-Headphones-5000-Series-Fig4Note

  • The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.

Use your earpieces

Connect the earpieces to your Bluetooth device

  • Turn on the Bluetooth function of your Bluetooth device. Open the charging box cover.
  • The blue LED flashes
  • The earpieces will search the last connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the earpieces will enter pairing mode

Philips-TAT5506-Headphones-5000-Series-Fig5Tip

  • The earpieces cannot connect to more than 1 device at the same time. If you have two paired Bluetooth devices, only turn on the Bluetooth function of the device that you want to connect.
  • If you turn on the Bluetooth function of your Bluetooth device after turning on the earpieces, you have to go to the Bluetooth menu of the device and connect the earpieces to the device manually.

Philips-TAT5506-Headphones-5000-Series-Fig4Note

  • If the earpieces fail to connect to any Bluetooth device within 3 minutes, it will turn o automatically to save the battery life.
  • In some Bluetooth devices, connection may not be automatic. In this case, you have to go to the Bluetooth menu of your device and connect the earpieces to the Bluetooth device manually.

Control ANC (Active Noise Cancellation)

Enable ANC

Different ANC mode can be toggled via double tap on the right earpiece.

  • ANC function is auto active when put into the ear
  • Touch the MFT twice, it will change to awareness mode
  • Touch the MFT twice again, it will turn the ANC function

Philips-TAT5506-Headphones-5000-Series-Fig13

Philips-TAT5506-Headphones-5000-Series-Fig5Tip

  • Removing the earpieces will automatically activate sleep mode. When you put the earpieces back they will return to active mode.

Philips-TAT5506-Headphones-5000-Series-Fig14

Power on/off

Philips-TAT5506-Headphones-5000-Series-Fig15

Manage your calls and music

Philips-TAT5506-Headphones-5000-Series-Fig16

Voice Assistant

Philips-TAT5506-Headphones-5000-Series-Fig17

Earpieces LED indicator status

Philips-TAT5506-Headphones-5000-Series-Fig18

Charging box LED indicator status

Philips-TAT5506-Headphones-5000-Series-Fig19

Reset the earpieces

If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default settings.

  • On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT5506 from the device list.
  • Turn off the Bluetooth function of your Bluetooth device.
  • Return earpieces to charging box and open the lid.
  • Press button on box twice.
  • Follow steps in “Use your earpieces connect the earpieces to your Bluetooth device.”
  • Pair the earpieces with your Bluetooth device, select Philips TAT5506.

If there is no response from the earpieces, you can follow the below step to reset the hardware of your earpieces.

  • Tap and hold multi-function touch for 10 seconds.

Technical data

  • Music play time (ANC on): 7+21 hours
  • Music play time (ANC of): 8+24 hours
  • Standby time: 55 hours
  • Charging time: 2 hours
  • Lithium-ion battery 55 mAh on each earpiece, Lithium-ion battery 550 mAh on charging box
  • Bluetooth version: 5.2
  • Compatible Bluetooth profiles:
  • HFP (Hands-Free Profile)
  • A2DP (Advanced Audio
  • Distribution Profile)
  • AVRCP (Audio Video Remote Control Profile)
  • Supported audio codecs: SBC, AAC
  • Frequency range: 2.402-2.480 GHz
  • Transmitter power: < 10 dBm
  • Operating range: Up to 10 meters (33 feet)
  • Auto power o
  • USB-C port for charging
  • Low battery warning: available

Philips-TAT5506-Headphones-5000-Series-Fig4Note

  • Specifications are subject to change without notice.

Notice

Declaration of conformity

Hereby, MMD Hong Kong Holding Limited declares that the product is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and UK Radio Equipment Regulations SI 2017 No 1206. You can find the Declaration of Conformity on www.philips.com/support.

Disposal of your old product and battery

Philips-TAT5506-Headphones-5000-Series-Fig20Your product is designed and manufactured with high quality materials and components which can be recycled and reused.

Philips-TAT5506-Headphones-5000-Series-Fig21This symbol on a product means that the product is covered by European Directive 2012/19/EU.

This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service center to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Remove the integrated battery

If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces.

  • Make sure the earpieces are disconnected from the charging box before removing the battery.

Philips-TAT5506-Headphones-5000-Series-Fig23

  • Make sure the charging box is disconnected from the USB charging cable before removing the battery.

Philips-TAT5506-Headphones-5000-Series-Fig24

Compliance with EMF

This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

Environmental information

All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (butter) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.

Notice of compliance

The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

  • This device may not cause harmful interference, and
  • This device must accept any interference received, including interference that may cause undesired operation.

Trademarks

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners.

Siri

Siri is a trademark of Apple Inc., registered in the U.S. and other countries.

Google

Google and Google Play are trademarks of Google LLC.

DOWNLOAD PDF LINK

tat5506bk_00_dfu_aen

https://www.philips.com.pk/c-p/TAT5505BK_00/5000-series-in-ear-true-wireless-headphones

Leave a Reply