VOYAGE C002-VA-1000 HD Streaming Drone Guide

VOYAGE C002-VA-1000 HD Streaming Drone Guide

PACKAGE CONTAINS:

FEATURES

• The compact fold-in design allows for easy portability
• New obstacles tons Anne raping George Will and the drone to automatical circumvent walls and
• Air pressure sensor locks flight altitude for stable video footage
• Takes video and still shots with an onboard HD Camera
• 6 axis avro for extremely stable flight and maneuverability

REMOTE CONTROL BATTERY INSTALLATION

1. Unscrew and remove the battery cover from the back of the controller.
2. Install 3 fresh “AAA” alkaline batteries into the controller as shown in diagram A. Replace the battery cover and secure it.
3. Turn over the controller and press the power button. If the power indicator turns on you have installed your batteries properly.

Battery Cover
CHARGING THE VA-1000 LI-POLY BATTERY

1. Connect the USB charger to the battery charging socket (see diagram B).
   CAUTION: The USB plug fits the charging socket only in one way. Do not force it. Improper the connection will damage the VA-1000’s battery.
2. Connect the USB end of the cable to your computer’s USB port or a USB wall charger (see diagram C).
3. The indicator light on the USB charger will turn to solid red to indicate that the battery is charging. The red LED indicator will turn off when charging is completed.
4. The average charging time is approximately 50-60 minutes ( via 5.0V – 2A USB wall charger). A fully charged VA-1000 can fly for 5-6 minutes depending on the environment and user input.
   IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!

INSTALL THE VA-1000 BATTERY
Push the fully charged battery into the battery compartment then lock the end with the battery locks. (see diagram D) The battery only fits one way to the battery compartment, do not force it.

HOW TO EXPAND AND FOLD YOUR
VA-1000 Before flying your VA-1000, you need to expand the foldable arms out. Turn your VA-1000 over, bottom side facing you, pull and expand the 4 arms as shown in the diagram below carefully. Make sure the arms are fully expanded to the position. After flying your VA-1000, it is recommended to fold all 4 arms back in. When expanding or folding your VA-1000, make sure to be gentle.(see diagram.

VA-1000 DIAGRAM

CONTROLLER DIAGRAM

WARNING
DO NOT FLY YOUR VA-1000 IN FOUL WEATHER!

FLIGHT PREPARATION

• Verify that there are 3″AAA” batteries inside the remote control unit and that the VA-1000 battery has been fully charged.
• Make sure to be in a large open space preferably a field or a park with an open radius of at least 200 feet.
• Make sure to start your drone on a clean level surface before take-off. Mind. Pick a day with zero wind oriented in ely ligne wild conditions while earning so to rate off.

SYNCING YOUR VA-1000
Important! When syncing your VA-1000 with the controller always make sure that the drone is on a flat-level surface and that your digital trim settings are in the center position.

1. Before starting, make sure that the power on your controller is off and the battery is removed from the VA -1000. Make sure that there are no other 2.4G devices in the area.
2. Insert the battery into the VA-1000 and set it down on a flat-level surface. Press down the power button and hold for a few seconds (see diagram F). The LED lights on the drone should begin to flash.
3. Quickly turn ON the remote and you will notice that the top red LED light on the face of the controller.
4. Push the throttle stick up until it stops and then pull it back down to the bottom (see diagram below). When pushing the stick up or pulling the stick down you should hear a high-pitched beep both ways. The indicating lights on the drone and controller will stop flashing and stay solid. You have successfully synced your VA-1000 and are ready to fly. If this doesn’t happen, repeat steps 1-4.

NOW YOU ARE READY TO FLY!

If you have successfully synced your VA-1000 to your controller as explained on page 4 you are now ready to fly. Before beginning to fly your drone you should familiarize yourself with how to start and stop the rotors, how to use your auto land feature, and how the controls work so please carefully read and familiarize yourself with various control features explained in the next. Once again as a beginner pilot, you should learn how to Control to drive in a log com elmore experience with zero or very light wind. Do not try to fly your

RECOGNIZING THE FRONT & REAR OF THE

VA-1000 Even though the VA-1000 has four rotors there is still a front or “forward” facing direction and a “rear” or backward facing direction. The front and forward-facing direction of the VA-1000 is the side with a camera (see diagram G). The rear and backward-facing direction of the drone is the side with a red light (see diagram G).

AUTOMATICALLY TAKE OFF / LAND
Make sure you have properly synced The VA-1000.

• simply press the Auto Start/Land button, and your VA-1000 will automatically take off.
• To stop or land the VA-1000 just Press the Auto Start/Land button again and the VA-1000 will descend and land automatically (see diagram 1).

Tips:
You also can move the two control sticks simultaneously down inside or outside corners, and hold them till the blades start spinning. Release the control sticks and push the throttle stick slowly to take off manually (see diagram H2).

SPEED SELECT BUTTON
Then you is on your tA-10 sine (sLow sped mode to increase the speed semut Select the speed setting button (see remote diagram on pg 3) you will hear beeping sounds of the controller will show you what speed setting you are on. Speed settings can be set before the flight or during the flight.

FLIGHT CONTROL
Below is a list of basic flight functions for your long-range remote to control the VA-1000. While learning to fly your VA-1000 it is best to start in a large space with the drone facing away from you until you get used to the basic controls. As you master flying your VA-1000 you can move to more advanced maneuvering techniques. Practice makes perfect!

Move the left Throttle stick up to increase the propeller speed and the VA-1000 will accelerate and ascend. Move the left Throttle stick down to decrease the propeller speed and the VA-1000 will decelerate and descend (see diagram l). While in the air, move the left Throttle stick left and the VA-1000 will rotate left.

Move the left Throttle stick right and the VA- 1000 will rotate right (see diagram J). While in -200 will tear for varection Stick up Move the right Direction Control down and the VA-1000 will move backward (see diagram K). While in the air, move the right Direction Control left and the VA-1000 will bank to the left. Move the right Direction Control and the VA-1000 will bank to the right (see diagram L).

FLIGHT PRACTICE
To master flying your aircraft try practicing the exercises shown below, start with simple vertical takeoffs, Inanivers. God/lick and have un rotating-Once those are mastered move on to square and cross

ADJUSTING THE TRIM

NOTE:
The VA-1000 is already properly trimmed and calibrated right out of the box and should not require any trim adjustments before flying. Some more experienced pilots may want to adjust trim settings for their style of flying. After several crashes, you may need to adjust the trim settings for the VA-1000 to be more balanced.

Forward/Backward Trim 

• If your VA-1000 is moving forward or backward automatically, you may need to adjust the FORWARD/BACKWARD TRIM buttons.
• If your VA-1000 drifts forward, push and release the BACKWARD TRIM button repeatedly until the moving stops and proper flight is maintained.
• If your VA-1000 drifts backward, push and release the FORWARD TRIM button in the same manner until the problem is resolved (see diagram M).
• From time to time, you may have to adjust the FORWARD or BACKWARD TRIM buttons to ensure the VA-1000 will hover in mid-air and respond accurately to your commands.

Banking Left/Right Trim

• If your VA-1000 is not steadily hovering and is banking to the left or right automatically, you may need to adjust the LEFT BANK or RIGHT BANK Trim buttons.
• If your VA-1000 banks to the left, push and release the RIGHT BANK TRIM button repeatedly until the banking stops and proper flight is maintained.
• If your VA-1000 banks to the right, push and release the LEFT BANK TRIM button in the same manner until the problem is resolved (see diagram N).
• From time to time, you may have to adjust the LEFT and RIGHT BANK TRIM to ensure the VA-1000 will steadily hover in mid-air and respond accurately to your commands.

NOTE:
The use of the Trim buttons utilizes sounds. A single long Beep indicates the product is center trimmed. When there’s no sound when pressing the trim the product is trimmed to the maximum on a particular side.

CALIBRATING THE VA-1000
NOTE:
Your VA-1000 comes per-calibrated out of the box so you are ready to fly. persevere erase position to assist sed sensors, you may notice that your drone is drifting and can This most likely means that you need to recalibrate your VA-1000. Please follow the simple instructions below.

1. Place the VA-1000 on a flat-level surface
2. Make sure the VA-1000 is on and that the controller is synced (refer to syncing pg 4). Do not start the blades. Instead, move both the throttles and control stick down and to the right corner (see diagram R). You will see the lights on the drone rapidly flash and stop. Once the lights stop flashing you have completed your calibration and are ready to fly!

TROUBLESHOOTING:

If you do not see the lights flash, first remove the battery from the drone then turn it off Put Cheetel mate sic send the way, and the out cour a team. When you tear one ep one it 000 is synced to the controller and you are ready to calibrate

1. HOW TO PERFORM 360° STUNT ROLLS Performing 360° stunt rolls with the VA-1000 is as easy as 1-2-3: 1. Hover the VA-1000 in still position making sure that you have at least 5 feet of clearance above and below the quadrocopter. Set the speed settings to mode 2 or 3, the VA-1000 can not do the stunt in T(Training) mode and speed 1(SLOW).
2. Press the 360 stunt button down and you will enter the stunt roll mode which is indicated by rapid beeping sounds(see diagram S).
3. Determine which direction you want it to flip and quickly push the right control stick in the direction you want to flin your WA 1000 leoo dinaram T)I

NOTE:
To exit the stunt roll mode without a flip, you can press the button again. The beeping sound will stop.

USING YOUR ON-BOARD CAMERA AND VIDEO RECORDER
Your VA-1000 comes equipped with an onboard digital camera(1280×720 pixels, 25 frames per second) that takes both video and still photographs. Now you can have hours of fun creating aerial photography and videos for family and friends.

WHAT YOU WILL NEED TO GET STARTED USING YOUR CAMERA

1. One microSD card (not included).
2. One microSD card reader(included).
3. A Computer with a USB port and Windows Media Player or other Media player that can play AVI files(not included).

FORMATTING YOUR MICRO SD CARD
Before you can begin to take videos or digital photographs you must first format your microSD card. To format your microSD card simply place the microSD card into the included USB SD card reader and plug it into your Deshiope gs dick On the con and log a rocoto toro feat your mira car will appear on your

TAKING DIGITAL PHOTOS

To take photographs short press the CAMERA button of the controller (refer to CONTROLLER DIAGRAM on pg. Sime indicates that a picture has been an “EP” and the red and white LED light on the will lash one.

RECORDING VIDEOS
and Lennie las intel ameras ar ashing to indicate that an I le be and the cam is recording. To stop the video recording, long press the CAMERA button a second time, and you will hear a “beep” indicating that the video recording has stopped and the Camera is in ready mode again.

REMOVING YOUR
microSD CARD To remove your microSD Card push in gently on the back of the SD card with your thumb or forefinger until you hear and feel a”clicking sound”. The microSD card will “pop out” slightly and is ready for removal. Simply grab and pull gently away from the VA-1000’s camera port to remove the card. Always store your microSD card in a clean, safe, and cool environment.

DOWNLOADING AND CLEARING SPACE ON YOUR
microSD CARD Plug your microSD card into the microSD card reader and connect to your computer. It is best to always download all your videos and pictures onto your computer and not store this data on your microSD card. After downloading your photos and videos, follow your computer’s instructions to “delete” files on your microSD card.

LIVE VIDEO STREAMING SETUP

Your VA-1000 comes equipped with an on board digital camera that takes both video and still photographs to your mobile devices. WHAT YOU WILL NEED TO GET STARTED USING YOUR CAMERA 1. One Apple or Android phone* (not included) 2. VIDEO DRONE APP installed (app store or Andriod market available) PHONE HOLDER AND PHONE INSTALLATION Insert the included phone holder hook (a) to the slots on the top of the controller properly, see the illustration below, When you install the phone holder correctly you can use it to hold your phone (see diagram U4)

TROUBLESHOOTING YOUR VA-1000

REPLACING THE PROPELLER BLADES

Your VA-1000S propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing at high-speed may cause damage to your VA-1000’s propellers.

1. The VA- 1000 has four sets blades, two sets blades with indication number A & B on front, and two sets blades with indication number B & A on the rear (see the diagram V).
2. When replacing the propeller blades, make sure to match the indication markings on the blades.
3. Unscrew and take off the damaged blade.
4. Replace with new correct blade.

BLADES GUARD INSTALLATION
Your VA- 1000 come with the blade guard for safety flight, it is recommended for beginners. Simply attached the 4 blade guards to each of landing gea (see the diagram W).

BATTERY WARNINGS

RECHARGEABLE BATTERY:
This VA-1000 uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery properly according to local disposal requirements.

CONTROLLER BATTERIES:
Remote control requires 3 “AAA”batteries (not included). Please read the important battery safety warning below.

• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).
• Do not mix old and new batteries.
• Renargeabie aleatene so e remove ecom the tem before being charged (f removable).
• Rechargeable batteries are only to be charged under adult supervision.
• Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations.
• They balytestine same ot equirent peas tecommended are to be used.
• Batteries are to be inserted with the correct polarity (see inside booklet for diagram).
• Do not dispose batteries in a fire – batteries may leak or explode.

CARE AND MAINTENANCE

• Always remove the batteries from the wireless remote control when it is not being used for an extended period of time.
• To clean, gently wipe the remote control and VA-1000 with a clean damp cloth.
• Keep the toy away from direct heat or sunlight.
• Do not submerge the toy into water. This can damage the unit beyond repair.
• Parental guidance recommended when installing or replacing the batteries.

Limited 90-Day Warranty

AMAX Group USA warrants to the original consumer that this product is free from any electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our warranty center ALONG WITH THE ORIGINAL RECEIPT evidencing that the product was purchased from an approved AMAX retail partner and that the product is still within the 90 day warranty period.

The warranty covers normal consumer use and does not cover damage that occurs in shipment or failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. Removal of any parts/components voids all warranties. This warranty does not cover cost of repairs made or attempted outside by third-party individuals or companies.

Any applicable implied warranties, including warranties of merchantability and fitness, are hereby limited to 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded. Some states do not allow limitations on the duration of implied warranties and do not allow exclusion of incidental or consequential damages, so the above limitations and exclusions in these instances may not apply.

REPAIR/REPLACE PRODUCT

If your product begins to malfunction or stop working, immediately contact our warranty center (contact details listed below). If it is determined that a return is necessary, our warranty department will issue you an RMA number/form and an address to the nearest return center for shipping the product to us. When honoring the warranty, AMAX reserves the right to either repair, replace or refund the product.

IMPORTANT NOTICE:
We will reject and return to sender returns that are not accompanied by an AMAX issued RMA form and RMA number so make sure to contact our warranty center before attempting to return your product!

REPAIR/REPLACE PRODUCT
If your product begins to malfunction or stop working, immediately contact our warranty center (contact details listed below). If it is determined that a return is necessary, our warranty department will issue you an RMA number/form and an address to the nearest return center for shipping the product to us.

When honoring the warranty, AMAX reserves the right to either repair, replace or refund the product. IMPORTANT NOTICE: We will reject and return to sender returns that are not accompanied by an AMAX issued RMA form and RMA number so make sure to contact our warranty center before attempting to return your product!

REFERENCE LINK