Wizard 2 Wired Video Intercom Kit User Manual

Wizard 2 Wired Video Intercom Kit User Manual

Part 1 Indoor Monitor

• A–Ringtone Volume Adjustment
• B–Voice Volume Adjustment
• C–Chroma/Contrast Adjustment
• D–Brightness Adjustment

Features:

1. Soft-Touch button operation
2. Two-Way voice communication
3. Dual door release options
4. Volume, brightness & contrast adjustable
5. Surface mounted
6.  Wire installation

TECHNICAL SPECIFICATIONS

Display	7″ Color TFT LCD Screen
Monitoring Timer	30 seconds
Talk Timer	120 seconds
Ringtone Timer	30 seconds ringing,90 seconds waiting
Power Consumption	<0.5W (standby) and <10W (operating)
Voltage Input to Power Supply	100VAC-240VAC,50/60Hz
Voltage Output from Power Supply	18VDC,1500mA
Operational Temperature Range	-25℃ ~ 65℃

GENERAL NOTES 

1. Do not put an Indoor Monitor in wet areas
2. Do not place the Indoor Monitor on an unstable surface, to prevent malfunction or damage caused by falls.
3. Keep Indoor Monitors out of the reach of small children.
4. Please do not use needles and other sharp objects to press the Indoor Monitor buttons.
5. Please don’t hit, shake or throw. Handle with care.
6. Do not install near any electrical devices, dimmers, ballasts, or high-voltage wiring.

CLEANING AND MAINTENANCE

1. Indoor Monitor is not water-proof and do not use it in high humidity places, like bathrooms.
2. If the screen is dirty, use a soft, dry cloth to gently wipe the screen.

WARNING
Please use the dedicated power supply provided Use any other power supply in this kit by Rongtai. will void the warranty and may cause system damage.

IMPORTANT NOTE
A. The End-of-Line Resistor Jumper
The end-of-line resistor jumper is used to adjust the video on the monitor, which is located on the back side of the monitor, and accessible through the opening in the plastic housing. If your installation has only a single monitor, the end-of-line resistor jumper must remain on the monitor. If your installation has multiple monitors, the end-of-line resistor jumper must remain in place on the monitor which is farthest from the outdoor station, and must be removed from the other monitors.

B. Secondary Door Bell (Option)
A secondary doorbell push button can be connected to a monitor to the terminal located on the back of the monitor marked CN5. This can be used as a notification that a visitor has reached a second door after being let through the first door. When the push button is depressed the monitor will chime twice.

C. Removing Remote Nameplate
Press down on one side of the plastic nameplate cover and then slide the plastic cover towards that side. The opposite side will pop up allowing you to remove it.

Part 2 Outdoor Station

Features:

1. Aluminum alloy panel, vandal resistant
2. Water-resistant
3. Surface-mounted
4. Calling/Talking functions
5. Powered by indoor monitor
6. Backlit call button and name holder

TECHNICAL SPECIFICATIONS 

Camera Type	Color HD CMOS Camera
Camera Viewing Angle	90°
Minimum Illumination	0.1 LUX
Night Light Compensation	4 White LEDs
Power Consumption	<0.1W (standby) , <3W (operating)
Operation Temperature Range	-25℃ ~ 65℃

Part 3 System Description

NOTES:

1. Maximum 3 indoor monitors and 2 outdoor stations
2. Each indoor monitor needs a separate power supply.
3. Each indoor monitor can monitor each of the (up to 2) outdoor stations.
4. Cables of the system: Wire≥0.5mm², from outdoor station
5. To the farthest indoor monitor distance≤70m.

USER OPERATION

Calling
When the ‘CALL’ button is pressed, the indoor monitor(s) show the visitor’s image from the appropriate outdoor station. Press the ‘TALK’

button to talk to the visitor.

Monitoring
When the ‘MONITOR’ button is pressed from any of the indoor monitors, you can visually monitor and hear the sounds around the outdoor station(s). The monitoring function will shut off automatically after 30 seconds, or you can shut it off by pressing the ‘MONITOR’ button again.

Unlocking
Under the standby mode or while talking, press ‘Unlocking’ button 1, and it will activate the dry contact; During a call from an outdoor station ‘Unlocking’ button 2, it will send 13.8V to the door strike.

Ringtone Volume Adjustment (on the monitor)
Adjust this to set the volume of the ringtone.

Voice Volume Adjustment (on the monitor)
Adjust this to set the listening voice volume

Brightness Tone (on the monitor)
Adjust this control to adjust the picture brightness.

Chroma/Color (on the monitor)
Adjust the chroma to get your desired color.

Part 4 System Installation & Connection

SCREW TERMINAL CONNECTIONS 

PLUG-IN HARNESS CONNECTIONS

CONFIGURATION DIAGRAM 

Part 5 Remote Installation Notes

• The proper height of an indoor monitor or outdoor station is between 63″-67″(160-170cm) from the ground. This may vary on each installation. The view range should be actively tested before completion.
• The viewing window of the door camera is about 19.5″ (50cm) vertically and 27.5″ (70cm) horizontally.
• Narrow space may cause feedback echo on the monitor voice function. Direct sunshine can cause blurry or ghost-like pictures on the monitor
• Installing units too close to electrical lines/dimmers/ballasts/or other electrical devices may cause audio and/or video interference.

REFERENCE LINK

https://wizard-tk.com/