LiftMaster 888LM MyQ Garage Door Wall Control Panel User Manual

LiftMaster 888LM MyQ Garage Door Wall Control Panel User Manual

COMPATIBLE ACCESSORIES

Security+ 2.0™ Accessories:                                                           MyQ® Accessories:
Model 891LM    1- Button Remote Control                                              Model 823LM Remote Light Switch
Model 893LM     3-Button Remote Control                                             Model 825LM Remote Light Control
Model 890MAX 3-Button Mini MAX Remote Control                         Model 828LM LiftMaster® Internet Gateway
Model 893MA    3-Button MAX Remote Control                                   Model 829LM  Garage Door and Gate Monitor
Model 895MAX  3-Button Premium MAX Remote Control
Model 877LM Wireless Keyless Entry
Model 877MAX Wireless MAX Keyless Entry

INSTALLATION

Install the MyQ® Control Panel in place of the existing door control. If an additional door control is needed, the wireless door control model 885LM can be programmed to the MyQ® Control Panel. To program the 885LM to the MyQ® Control Panel, follow the remote control programming steps.

1.  Disconnect all electrical and battery power (if applicable) to the garage door opener.
2.  Remove the existing door control from the wall.
3.  Note the polarity of the wires connected to the existing door
   control.
4. Connect the wires to the new MyQ® Control Panel. Make sure the polarity is correct.
5.  Mount the MyQ® Control Panel to the wall.
6.  Reconnect power. The yellow command LED and the red learn LED will blink quickly for up to 5 minutes as the control panel recharges.
7.  To test the control panel, press the push bar to activate the garage door opener.

PROGRAMMING

REMOTE CONTROL

1.  Press the MyQ® Control Panel LEARN button twice, the red learn LED will turn on.
2.  Press the button on the remote control that you wish to operate your garage door.

KEYLESS ENTRY

1. Press the MyQ® Control Panel LEARN button twice, the red learn LED will turn on.
2.  Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad.

MyQ® ENABLED ACCESSORIES

1.  Press the MyQ® Control Panel LEARN button twice, the red learn LED will turn on.
2. Press the LEARN button on the MyQ® device.*

Model 825LM
Remote Light Control Light module can be synchronized with the garage door opener light bulbs.

Model 829LM
Garage Door and Gate Monitor Indicates the status of your garage door from inside the home and allows you to close an open garage door from inside the house.

Model 823LM
Remote Light Switch Light module can be synchronized with the garage door opener light bulbs.

INTERNET GATEWAY
The LiftMaster® Internet Gateway gives you control of your garage door from your internet connected computer or mobile device. You must have your internet gateway registered to your customer account at
myliftmaster.com in order to use it with the MyQ® Control Panel.  To program your control panel to the LiftMaster® Internet Gateway:

1.  Go to myliftmaster.com from a computer or mobile device.
2.  Click on “Manage Places>Add New Device>Garage Door Opener” and follow the directions.
3.   The red learn LED will turn on.
4.  The red learn LED will turn off when programming is complete. Once the control panel is learned, it will appear on your screen. You can then name the device (e.g., My Control Panel, etc.).

Model 828LM LiftMaster® Internet Gateway

FUNCTIONS

PUSH BAR
Press the push bar to open/close the door.

LIGHTS
Press the LIGHT button to turn the garage door opener lights on or off.  The LIGHT button will not control the lights when the door is in motion. To change the amount of time the garage door opener lights will stay on:Press and hold the LOCK button until the garage door opener lights flash.

Activate:
Start with the garage door opener lights on.

Deactivate:
Press and hold the LIGHT button until the garage door opener lights turn on, then off again.

TROUBLESHOOTING

• If the yellow command LED does not turn on, reverse the wires connected to the R and W terminals of the control panel. Replace wire if necessary.
•  If yellow and red LEDs are blinking slowly, the control panel is not compatible with your garage door opener.
•  If the yellow and red LEDs are blinking quickly, the control panel is charging, and may take up to 5 minutes to become operational.

ONE YEAR LIMITED WARRANTY

LiftMaster warrants to the first consumer purchaser of this product that is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.

DOWNLOAD PDF

LiftMaster 888LM MyQ Garage Door Wall Control Panel User Manual

REFERENCE LINK

https://www.liftmaster.com