Maytronics 8151620 Pool Cleaner User Manual
INTRODUCTION
Thank you for purchasing a Maytronics Robotic Pool Cleaner. We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and cost effective pool cleaning. Its reliable filtration in all pool conditions, active brushing, and all-surface climbing brush enhance maximum pool hygiene. The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technology, long lasting performance and easy maintenance. You and your family will be free to enjoy swimming with full confidence that your pool is completely clean.
SPECIFICATIONS
- Motor protection: IP 68
- Minimum depth: 0.80m/2.6ft
- Maximum depth: 5m/16.4f
Digital switch-mode power supply
- Input – 100-250 AC VOLTS
- 50-60 Hertz
- 180 Watt
- Output – <30 VDC
- IP 54
WARNINGS AND CAUTIONS
Warnings
- Use the originally supplied power supply only
- Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter (ELI)
- Keep the power supply out of standing water
- Position the power supply at least 3.5 m (12 ft) away from the edge of the pool
- Do not enter the pool while the Pool Cleaner is working • Unplug the power supply before servicing
- Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
POOL CLEANER PARTS
Dolphin Explorer Classic 9
Brushes
Power supply unit
Filtration
USING THE POOL CLEANER
The Pool Cleaner is very simple to use. Simply put it into the pool and make sure that it is properly sitting on the floor of the pool. Turn it ON and let it get the job done.
Setup
Before using the Pool Cleaner for the first time perform the following steps:
Unwind the cable and stretch it out completely so that it has no kinks.
Some models arrive with plastic coverings on the brushes. Remove them before use.
Adjusting the handle angle
The robot’s handle should be adjusted and locked diagonally in order to ensure optimum cleaning results. The handle angle can be adjusted also to determine the speed at which the robot advances along the water line.
To adjust the handle angle: A. Press the latch down and hold it in position. B. Move the handle to the desired position and release the latch to hold the handle in place.
Position the power supply so that it is approximately in the middle of the long side of the pool at a distance of 3m/10ft. Attach the floating cable to the power supply by inserting it with the notch on the connector (1) lined up with the groove in the socket on the power supply and turning clockwise (2).
Plug in the power supply and leave it in the OFF position:
Putting the Pool Cleaner into the pool
If your Pool Cleaner is equipped with brushes that contain sponges, dip the brushes in the water and squeeze them so that they will absorb water the first time you use the Pool Cleaner, or if the brushes have dried out between uses. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions. To avoid kinks in the floating cable, place approximately enough cable in the water for the Pool Cleaner to reach the farthest corner of the pool.
Turn the power supply ON. The Pool Cleaner will now operate until it has reached the end of the cleaning cycle
Removing the Pool Cleaner from the pool
Turn OFF and unplug the power supply
Using the floating cable, bring the Pool Cleaner to the pool’s edge. Using the handle remove the Pool Cleaner from the pool.
ROUTINE MAINTENANCE
Cleaning the filters of the cartridges
Unplug the power supply before any servicing activity.
Note: Do not let the filters of the cartridges dry out before cleaning.
- Open the filter covers and remove the cartridges from both sides of the robot.
- Open the clips and remove the filters.
- Clean the filters with a hose.
- Reassembling the filter elements Insert the locating tabs at the bottom of the filter element into their grooves on the base frame then close the “S” clip.
OFF SEASON STORAGE
If the Pool Cleaner will not be in use for an extended period, perform the following storage steps:
- Make sure that no water is left in the Pool Cleaner
- Thoroughly clean the filters of the cartridges and insert them in place
- Roll up the cable so that it has no kinks and place it on the Caddy
- Store the pool cleaner upright on the Caddy in a protected area out of direct sun/rain/frost at a temperature of between 5˚-45˚C / 41˚-113˚F.
TROUBLESHOOTING
If the suggested solutions do not solve the problem contact your dealer:
To move the floats back to their original position: while pressing the release button on the base of the handle float – push the handle float back.
REFERENCE LINK
https://www.maytronics.com/en-us/
