RCA MD3790FM Swivel Mounts User Manual
Questions?
DISCLAIMER
Voxx Accessories Corp. has extended every effort to ensure to accuracy and completeness of this manual. However, Voxx Accessories Corp. does not claim that the information covers all installation or operational variables. The information contained in this document is subject to change without notice or obligation of any kind. Regarding the information contained herein, Voxx Accessories Corp. makes no representation of warranty, expressed or implied, and assumes no responsibility for the accuracy, sufficiency, or completeness of the information contained in this document.
WARNING INFORMATION
WARNING: FAILURE TO READ, THOROUGHLY UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO PERSONAL PROPERTY, OR VOIDING OF FACTORY WARRANTY! It is the responsibility of the installer to ensure all components are properly assembled and installed using the instructions provided. If you do not understand these instructions or have any questions or concerns, please contact customer service at 1-800-645-7750. Do not attempt to install or assemble this product if the product or hardware is damaged or missing. In the event that replacement parts or hardware are needed, please contact Customer Service at 1-800-645-7750. International customers needing assistance should contact the Dealer from which they purchased the product.
The included hardware is designed for use on vertical walls constructed of wood studs or solid concrete. A wood stud wall is defined as consisting of a minimum of 2×4 wooden studs (2” wide by 4” deep) with a maximum of 5/8” drywall. The included hardware is not designed for use with metal studs or cinderblock walls. If you’re uncertain about the construction of your wall, then please consult a qualified contractor or installer for assistance. For a safe installation, the wall you are mounting to must support 4 times the weight of the total load. If not, then the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure and hardware used in any installation method will safely support the total load.
Tools Required (Not Included)
Package Contents
Mounting Hardware Bags
Attach the mount arms to your TV
IMPORTANT!
Use extra care during this part of the installation. If possible, avoid placing your display facedown as it may damage the viewing surface.
NOTE:
This mount comes with a selection of different bolt diameters and lengths to accommodate a wide variety of display models. Not all of the hardware in the kit will be used. If you cannot find the appropriate bolt size in the kit provided, consult the manufacturer of your display for more information.
- Determine the correct diameter of the bolt to use by carefully trying one of each size (M-A or M-B) from the hardware kit. Do not force any of the bolts – if you feel resistance stop immediately and try a smaller diameter bolt.
- Determine if you need to use spacers.
- A. If the back of your display is flat and the mounting holes are flush with the surface, you probably won’t need to use the spacers.
- B. If the back of your display is curved, or has a protrusion, or if the mounting holes are recessed, you probably will need to use the spacers.
- Attach the mount arms to the back of your display using the bolts identified in Step 1 along with the M-C washers and spacers if needed.
Installation on wood stud
- Use a stud finder to locate two wood studs where you wish to install your mount. Mark both edges of each stud to help identify the exact center. NOTE: You must use the center of each stud to avoid cracking or splitting the wood during installation.
- Place the base of the mount against the wall over the marked studs. Use the included bubble level (C) to make sure the base is level and mark where the four mounting screws will go.
- Drill 4.5 mm (3/16”) pilot holes in the wall 2.2” deep.
- Place the base against the wall over the pilot holes
- Attach the wall mount base and arm to the wall using four of the mounting screws (W-A) and mounting washers (W-C) provided. Do not over-tighten these screws and do not release the wall plate until all screws are in place. Ensure that the wall mount base remains level after all screws are secured.
Installation on concrete
IMPORTANT!
For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and the display. The manufacturer takes no responsibility for failure caused by walls of insufficient strength.
- Place the base of the mount against the wall where you want to install it. Use the included bubble level (C) to make sure the base is level and mark where the five mounting screws will go.
- Drill five 10 mm (3/8”) holes in the wall where you marked, 2.56” deep. Remove any excess dust from the hole.
- Insert a concrete anchor (W-B) into each hole so that it is flush with the concrete surface. A hammer can be used to lightly tap the anchors into place if necessary. NOTE: If the concrete wall is covered by a layer of plaster or drywall, the concrete anchor must pass completely through the layer to rest flush with the concrete surface.
- Place the wall plate against the wall over the inserted anchors and attach it using the mounting screws (W-A) and mounting washers (W-C) provided. Do not over-tighten these screws and do not release the wall plate until all screws are in place.
Place your TV on the mount
- With the help of another person, carefully lift your TV with mounting arms attached and place it on the wall plate. Do not release the display until the mounting arms have securely hooked onto the wall plate.
- Screw the bolts at the bottom of each mounting arm until they touch the wall plate.
12-Month Limited Warranty
To obtain repair or replacement within the terms of the warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), and transportation prepaid, to an approved warranty station. For the location of the nearest warranty station to you, call toll-free to our control office: 1-800-645-4994. This Warranty is not transferable and does not cover products purchased, serviced, or used outside the United States or Canada. The Warranty does not extend to the elimination of externally generated static or noise. This Warranty does not cover damage caused by an AC adapter not provided with the product.
REFERENCE LINK
https://www.rcaaudiovideo.com/wall-mounts/full-motion/
